Disconnect the battery PEUGEOT RCZ 2012 Owners Manual
[x] Cancel search | Manufacturer: PEUGEOT, Model Year: 2012, Model line: RCZ, Model: PEUGEOT RCZ 2012Pages: 336, PDF Size: 14.1 MB
Page 38 of 336
36
Service overdue
For 7 seconds after the ignition is switched on, the spanner fl ashes
to
indicate that the service must be carried out as soon as possible.
Example:
the service is overdue by 300 miles.
For 7 seconds after the ignition is switched on, the central screen indicates:
The spanner remains
on
in the small screen
to indicate that a service should have been
carried out.
The distance remaining may be weighted by the time factor,
depending on the driver's driving habits.
Therefore, the spanner may also come on if you have exceeded
the one year service interval.
Service indicator zero reset
Retrieving the service information
You can access the service information at any time.
This information appears when running through the manual check
procedure.
)
Briefl y press the "CHECK/000"
button.
The service information is displayed for a few seconds on the
instrument panel central screen, then disappears.
Following this operation, if you wish to disconnect the battery, lock
the vehicle and wait at least fi ve minutes for the zero reset to be
registered. After each service, the service indicator must be reset to zero.
The procedure for resetting to zero is as follows:
)
switch off the ignition,
)
press and hold the "CHECK/000"
button,
)
switch on the ignition; the distance recorder display begins a
countdown,
)
when the instrument panel central screen indicates "=0"
, release
the button; the spanner disappears from the small screen.
Page 56 of 336
54
Folding the key
)
First press this button to fold the key.
LOCATING YOUR VEHICLE
REMOTE CONTROL PROBLEM
Following disconnection of the vehicle battery, replacement of the
remote control battery or in the event of a remote control malfunction,
you can no longer unlock, lock or locate your vehicle.
)
First of all, use the key in the lock to unlock or lock your vehicle.
)
Then, reinitialise the remote control.
If the problem persists, contact a PEUGEOT dealer as soon as
possible.
Reinitialisation
)
Switch off the ignition.
)
Turn the key to position 2 (Ignition on)
.
)
Press the closed padlock immediately for a few seconds.
)
Switch off the ignition and remove the key from the ignition switch.
The remote control is fully operational again.
Changing the battery
Battery ref.: CR1620 / 3 volts.
If the battery is fl at, you are informed by illumination of this
warning lamp, accompanied by an audible signal and an alert
message in the screen.
)
Unclip the casing using a coin at the notch.
)
Slide the fl at battery out of its location.
)
Slide the new battery into its location observing the original
direction.
)
Clip the casing.
)
Reinitialise the remote control.
This function allows you to identify your vehicle from a
distance, particularly in poor light. Your vehicle must be
locked.
)
Press the closed padlock on the remote control.
This will switch on the courtesy lamps and the direction indicators will
fl ash for a few seconds.
Page 66 of 336
64
BOOT
OPENING
)
Press this button for more than two seconds to unlock
the boot lid. The boot lid opens slightly.
)
Lift the boot lid.
This action also unlocks the doors and the fuel fi ller fl ap.
Using the manual control; vehicle unlocked
)
Press the opening control above the number plate.
)
Lift the boot lid.
CLOSING
)
Lower the boot lid using one of the interior grab handles.
)
If necessary, press the top of the boot lid to close it fully.
If the boot lid is not closed correctly:
- when the engine is running
, this warning lamp comes on,
accompanied by a message in the screen for a few seconds,
When selective unlocking is activated, the boot can also be
opened by a second press on the open padlock on the remote
control.
Using the remote control
Emergency locking
If the central locking system fails (fl at battery), you are advised to
disconnect the battery.
- when the vehicle is moving
(speed above 6 mph (10 km/h)), this
warning lamp comes on, accompanied by an audible signal and a
message in the screen for a few seconds.
Page 156 of 336
154
CHECKS
BATTERY
PARTICLE EMISSION FILTER (DIESEL)
On a new vehicle, the fi rst particle fi lter regeneration operations
may be accompanied by a "burning" smell, which is perfectly
normal.
Following prolonged operation of the vehicle at very low speed or
at idle, you may, in exceptional circumstances, notice the emission
of water vapour at the exhaust on acceleration. This does not
affect the behaviour of the vehicle or the environment.
The battery does not require any maintenance.
However, check that the terminals are clean and correctly
tightened, particularly in summer and winter.
When carrying out work on the battery, refer to the "Battery"
section for details of the precautions to be taken before disconnecting
the battery and following its reconnection.
The start of saturation of the particle emissions fi lter is
indicated by the temporary illumination of this warning lamp,
accompanied by an audible signal and a message on the risk
of blockage of the particle emissions fi lter.
As soon as the traffi c conditions permit, regenerate the fi lter by driving
at a speed of at least 40 mph (60 km/h) until the warning lamp goes off.
If the warning lamp stays on, refer to the "Additive level" section.
Unless otherwise indicated, check these components in accordance
with the servicing and warranty booklet and according to your engine.
Otherwise, have them checked by a PEUGEOT dealer or a qualifi ed
workshop.
AIR FILTER AND PASSENGER COMPARTMENT FILTER
Refer to the servicing and warranty booklet for details of
the replacement intervals for these components.
Depending on the environment (e.g. dusty atmosphere)
and the use of the vehicle (e.g. city driving), replace them
twice as often if necessary
.
A clogged passenger compartment fi lter may have an adverse effect
on the performance of the air conditioning system and generate
undesirable odours.
Replace the oil fi lter each time the engine oil is changed.
Refer to the servicing and warranty booklet for details of the
replacement interval for this component.
OIL FILTER
Page 173 of 336
8/
PRACTICAL INFORMATION
BATTERY
The battery is located under the bonnet.
For access to it:
)
open the bonnet using the interior release lever, then the exterior
safety catch,
)
remove the plastic cover for access to the two terminals,
)
wait 2 minutes after switching off the ignition before disconnecting
the battery,
)
unclip the fusebox to remove the battery, if necessary.
STARTING USING ANOTHER BATTERY
)
Connect the red cable to the positive terminal (+) of the fl at
battery A
, then to the positive terminal (+) of the slave battery B
.
)
Connect one end of the green or black cable to the negative
terminal (-) of the slave battery B
.
)
Connect the other end of the green or black cable to the earth
point C
on the broken down vehicle.
)
Operate the starter, let the engine run.
)
Wait until the engine returns to idle and disconnect the cables.
ACCESS TO THE BATTERY
The batteries contain harmful substances such as sulphuric
acid and lead. They must be disposed of in accordance with
regulations and must not, in any circumstances, be discarded with
household waste.
Take used remote control batteries and vehicle batteries to a
special collection point.
Page 174 of 336
172
DISCONNECTING / RECONNECTING THE
CABLES
To avoid discharging the battery, do not leave the vehicle lighting
on repeatedly with the ignition off (refer to the "Energy economy
mode" paragraph).
It is advisable to disconnect the battery if the vehicle is to be left
unused for more than one month.
Do not disconnect the terminals while the engine is running.
Do not charge the batteries without disconnecting the terminals
fi rst.
Before disconnecting the battery
Wait 2 minutes after switching off the ignition before disconnecting
the battery.
Retract the active spoiler then close the windows and the doors
before disconnecting the battery.
Following reconnection of the battery
Following reconnection of the battery, switch on the ignition
and wait 1 minute before starting to permit initialisation of the
electronic systems. However, if slight problems remain following
this operation, contact a PEUGEOT dealer or a qualifi ed
workshop.
Referring to the corresponding section, you must yourself
reinitialise:
- the remote control key,
- the electric windows and the automatic partial opening of the
door windows,
- the GPS satellite navigation system.
)
Raise the locking tab D
fully.
)
Position the open clip E
of the cable on the positive terminal (+) of
the battery.
)
Press vertically on the clip E
to position it correctly against the
battery.
)
Lock the clip by lowering the tab D
.
CHARGING THE BATTERY USING A BATTERY
CHARGER
)
Disconnect the battery from the vehicle.
)
Follow the instructions for use provided by the manufacturer of the charger.
)
Reconnect starting with the negative terminal (-).
)
Check that the terminals and connectors are clean. If they are
covered with sulphate (whitish or greenish deposit), remove them
and clean them.
Do not force the tab as locking will not be possible if the clip is not
positioned correctly.
Start the procedure again.
Page 303 of 336
301
FREQUENTLY ASKED QUESTIONS
QUESTIONANSWER SOLUTION
With the engine off, the system switches off after a few minutes of use.When the en
gine is switched off, the system's operating time depends on
the battery charge.
The switch-o
ff is normal: the system switches to economy mode and
switches off to prevent discharging of the vehicle's battery.
Start the vehicle's engine to increase the batterycharge.
Pla
yback of my USB memory stick starts only
after a very long wait (around 2 to 3 minutes).Some fi les supplied with the memor
y stick may greatly slow down access
to reading the memory stick (multiplication by 10 of the catalogue time). Delete the fi les supplied with the memory stickand limit the number of sub-folders in the fi le structure on the memory stick.
When I connect m
yiPhone as telephone and
to the USB port at thesame time, I am unable
to play the music fi les. When the iPhone connects automaticall
y as a telephone, it forces the
streaming function. The streaming function takes the place of the USBfunction which is then not useable, there is a period without sound of the
track being played with AppleÆ players.Æ
Disconnect and reconnect to the USB port (the USB function takes priority over streaming).