display Peugeot Traveller 2016 User Guide

32
Engine oil level
indicator
on versions fitted with an electric oil gauge,
information on the oil level is displayed in the
instrument panel for a few seconds when the
ignition is switched on, at the same time as the
service information.The level read will only be correct if
the vehicle is on level ground and the
engine has been off for more than
30


minutes.
Oil level correct
This is indicated by a message in the
instrument panel.
Oil level incorrect
This is indicated by a message in the
instrument panel.
If the low oil level is confirmed by a check using
the dipstick, the level must be topped-up to
avoid damage to the engine.
Oil level indicator fault
This is indicated by a message in the
instrument panel. Contact a Pe ugeoT d ealer
or a qualified workshop.
Dipstick
There are 2 marks on the
dipstick:
-

A
= max; never exceed this
level,
-

B
= min; top-up the level via
the oil filler, using the grade
of oil suited to your engine.
To locate the dipstick and the oil filler
cap for the Diesel engine
, refer to the
corresponding section.
Instruments

33
Traveller-VP_en_Chap01_instruments-de-bord_ed01-2016
AdBlue® fluid range
indicators
once the AdBlue® tank is on reserve or after
detection of a fault with the SCR emissions
control system, when the ignition is switched
on, an indicator displays an estimate of the
distance that can be covered, the range, before
engine starting is prevented.
In the event of simultaneous system fault and
low AdBlue
® level, the shortest range figure is
the one displayed.
In the event of the risk of non-starting related to a lack of AdBlue®
The engine start prevention system
required by regulations is activated
automatically once the AdBlue
® tank is
e m pt y.
Remaining range greater than 1 500 miles (2 400 km )
Pressing this button will display the remaining
range.
F

T
hen select "Diagnostic".
Above 3 000 miles (5 000 km), the value is not
specified. When switching on the ignition, there is no
automatic display of range in the instrument
panel.
The range is then displayed temporarily. You can access this information in the touch
screen, if your vehicle has one. F

Sel
ect the "Driving" menu.
Remaining range between 350 and 1500 miles (600 and 2 400 km)
When switching on the ignition, this warning
l amp comes on, accompanied by an
audible signal and the display of a message
(e.g.:
"Top up emissions additive: Starting
prevented in 900 miles") indicating the
remaining range expressed in miles or
kilometres.
When driving, the message is displayed every
200 miles (300 km) until the fluid has been
topped-up.
go t

o a P
e
ugeo
T d
ealer or a qualified
workshop to have the AdBlue
® topped-up.
You can also top-up the tank yourself.
F

Sel

ect " OPTIONS ".
For more information on AdBlue
® and
the SCR system , and in particular on
topping-up the AdBlue
®, refer to the
corresponding section.
1
Instruments

34
Remaining range between 0 and 350 miles (0 and 600 km)
When switching on the ignition, this warning
lamp flashes, accompanied by an audible
signal and the display of a message
(e.g. "Top up emissions additive: Starting
prevented in 350 miles") indicating the
remaining range expressed in miles or
kilometres.
When driving, the message is displayed every
30 seconds until the fluid has been topped-up.
go t
o a P
e
ugeo
T d
ealer or a qualified
workshop to have the AdBlue
® topped-up.
You can also top-up the tank yourself.
ot

her wise you will not be able to restart your
engine. Breakdown related to a lack of AdBlue
®
When switching on the ignition, this
warning lamp flashes, accompanied
by an audible signal and the display
of the message "Top up emissions
additive: Starting prevented".
The AdBlue
® tank is empty: the system required
by regulations prevents engine starting.
To be able to start the engine,
we recommend that you call on a
P
e

ugeo
T d
ealer or a qualified
workshop for the top-up required.
If you carry out the top-up yourself, it
is essential to add at least 3.8 litres of
AdBlue
® to the tank.
For more information on AdBlue
® and
the SCR system , and in particular on
topping-up the AdBlue
®, refer to the
corresponding section.
Instruments

35
Traveller-VP_en_Chap01_instruments-de-bord_ed01-2016
Starting prevented
ev
ery time the ignition is switched on, these
warning lamps come on, accompanied by an
audible signal and the display of the message
"
em

issions fault: Starting prevented".You have exceeded the authorised
driving limit: the starting prevention
system inhibits engine starting.
To be able to start the engine, you must call on
a P
e

ugeo
T d
ealer or a qualified workshop.
In the event of a fault with the SCR emissions control system
A system that prevents engine starting is activated automatically from 650 miles (1 100 km) after confirmation of a fault with the SCR emissions
control system. Have the system checked by a Pe ugeoT d ealer or a qualified workshop as soon as possible.
If it is a temporary fault, the alert
disappears during the next journey,
after self-diagnosis of the SCR system.
In the event of the detection
of a fault
These warning lamps come on, accompanied
by an audible signal and the display of the
message "
em

issions fault".
The alert is triggered when driving when the
fault is detected for the first time, then when
switching on the ignition for subsequent
journeys, while the fault persists. During an authorised driving phase (between
650 miles and 0 miles) (1 100 km and 0 km)
If a fault with the SCR system is confirmed
(after 30 miles (50 km) covered with the
permanent display of the message signalling
a fault), these warning lamps come on,
accompanied by an audible signal and the
display of a message (e.g.: "
em

issions fault:
Starting prevented in 150 miles") indicating
the remaining range expressed in miles or
kilometres.
While driving, the message is displayed every
30 seconds while the fault with the SCR system
persists.
The alert is repeated when switching on the
ignition.
You should go to a P
e

ugeo
T d
ealer or a
qualified workshop as soon as possible.
ot

her wise, you will not be able to restart your
engine.
1
Instruments

36
Distance recorders
The total and trip distances are displayed for
thirty seconds when the ignition is switched off,
when the driver's door is opened and when the
vehicle is locked or unlocked.When travelling abroad, you may
have to change the units of distance:
the display of road speed must be in
the official units (miles or km) for the
country. The change of units is done via
the screen configuration menu, with the
vehicle stationary.
Total distance recorder
It measures the total distance travelled by the
vehicle since its first registration.
Trip distance recorder
It measures the distance travelled since it was
reset to zero by the driver. F

W
ith the ignition on, press this
button until zeros appear.
Instruments

38
System that gives you information on the current journey (range, fuel consumption…).
Tr i p c o m p u t e r
Display of information
F Press the button on the end of the wiper control stalk to display the different trip
computer tabs in turn. F
o
r
, depending on equipment, press the
thumbwheel on the steering wheel .-
T
he current information with:
●
t
he range,
●
t
he current fuel consumption,
●
t
he Stop & Start time counter.
Tr i p s "1" and "2" are independent but their use
is identical.
For example, trip "1" can be used for daily
figures, and trip "2" for monthly figures.
-
Trip
"2" with:
●
t
he average speed,
●
t
he average fuel consumption,
●
t
he distance travelled,
f

or the second trip.
- Trip
"1" with:
●
t
he average speed,
●
t
he average fuel consumption,
●
t
he distance travelled,
f

or the first trip.
Depending on equipment, a 2
nd trip is available.
Instruments

39
Traveller-VP_en_Chap01_instruments-de-bord_ed01-2016
Trip reset
With LCD text instrument panel
F When the trip is displayed, press the button on the end of the wiper control stalk .F
o
r
, depending on equipment, press the
thumbwheel on the steering wheel for
more than two seconds.
F
W
hen the desired trip is displayed, press
the reset button in the instrument panel for
more than two seconds.
With LCD text or matrix
instrument panel
1
Instruments

40
A few definitions
Range
(miles or km)
The distance which can still be
travelled with the fuel remaining in
the tank (related to the average fuel
consumption over the last few miles
(kilometres) travelled).
This value may vary following a change
in the style of driving or the relief,
resulting in a significant change in the
current fuel consumption.
When the range falls below 20 miles (30 km),
dashes are displayed. After filling with at least
8 litres of fuel, the range is recalculated and is
displayed when it exceeds 60 miles (100 km). If dashes are displayed continuously
while driving in place of the digits,
contact a P
e

ugeo
T d
ealer or a
qualified workshop. This function is only displayed from
20 mph (30 km/h).
Current fuel
consumption
(mpg or l/100 km or km/l)
Calculated over the last few seconds.
Average fuel consumption
(mpg or l/100 km or km/l)
Calculated since the last trip reset.
Average speed
(mph or km/h)
Calculated since the last trip reset.
Distance travelled
(miles or km)
Calculated since the last trip reset.
Stop & Start time
counter
(minutes / seconds or hours /
minutes)
If your vehicle is fitted with Stop & Start, a time
counter calculates the time spent in ST
oP
m

ode during a journey.
It resets to zero every time the ignition is
switched on.
Instruments

41
Traveller-VP_en_Chap01_instruments-de-bord_ed01-2016
use this button to confirm.
us
e this button to quit.
us

e the buttons on either side of the touch
screen for access to the menus, then press the
virtual buttons in the touch screen.
Menus
Driving .
Allows certain functions to be switched
on and off and their settings adjusted.
Telephone.
Radio Media
.
Connected navigation . Settings
.
Allows configuration of the display
and the system.
Connectivity .
Adjust volume/Mute.
o

n/
of
f.
Touch screen
As a safety measure, the driver must
only carry out operations requiring
sustained attention with the vehicle
stationary. For more information on the touch
screen, refer to the Audio and
telematics section.
1
Instruments

43
Traveller-VP_en_Chap01_instruments-de-bord_ed01-2016
ButtonCorresponding function Comments
Vehicle settings
To deactivate/activate a
function, press
o
F
F/
oN.
T

o modify a setting (lighting
duration, ...) or find additional
information, press the symbol
for the function. Access to other functions with settings that can be adjusted.
Select or deselect the tabs at the bottom of the touch screen to sort the display of the desired
functions.
-

L
ighting:
-
"

Directional headlamps": activation/deactivation of the directional headlamps.
-
"gu

ide-me-home lighting": activation/deactivation of the automatic guide-me-home lighting.
-
"

Welcome lighting": activation/deactivation of the exterior welcome lighting.
-
"

Mood lighting": activation/deactivation of the interior mood lighting.
-

A
ccess:
-

"
Hands-Free Access": activation/deactivation of the motorized opening and closing of a side
door by the hands-free system,
-

"
Locks your vehicle after the motorized closing of a side door, using hands-free access.":
activation/deactivation of the locking of your vehicle after the motorized closing of a side door
by the hands-free system.
-

A
ssistance (driving aids):
-

"
Rear wiper in reverse": activation/deactivation of the operation of the rear wiper in reverse.
-

"
Recommended speed display": activation/deactivation of the speed limit recognition system,
allowing a speed setting to be given to the cruise control or speed limiter.
-
"

Collision risk alert and automatic braking": activation/deactivation of collision risk alerts.
-
"

Fatigue Detection System": activation/deactivation of the driver fatigue detection system.
Diagnostic List of current alerts.
Parking sensors Activation/Deactivation of the function.
Adjust speed settings Memorisation of speed settings for the speed limiter or active cruise control.
1
Instruments