display PONTIAC BONNEVILLE 2000 Owner's Guide

3-5
Temperature Knob (Passenger's Side)
The passenger's side knob changes the temperature of
the air coming through the system on the passenger's
side of the vehicle. Turn the knob toward the blue area
to decrease the set temperature. Turn the knob toward
the red area to increase the set temperature. When this
knob is adjusted, only the word PASS will be displayed
under the set temperature.
Fan Button
The button with the fan symbol allows you to manually
adjust the fan speed. Press the HIGH side to increase fan
speed and the LOW side to decrease fan speed.
Mode Button
Press this button to manually select the air delivery mode
to the floor, panel or windshield outlets. The system will
stay in the selected mode until the MODE or AUTO
button is pushed.Auto Button
Press the AUTO button to set the system to
automatically control the air delivery mode, fan speed,
A/C and RECIRC operations. Whenever you press
AUTO, the display will change to show the current
driver set temperature, automatic air delivery mode and
fan speed. After five seconds the display will change
back to the EXT (external) temperature outside
the vehicle.
Display
In full AUTO mode, the electronic climate control
system display will show the outside temperature,
labeled EXT for external temperature, and AUTO.
If you press the MODE button to select an air delivery
mode, the display will change to also show you the
current system mode. If you press HIGH or LOW on the
fan button, the display will change to show the selected
fan speed. After five seconds, the display will change
back to show the EXT temperature and the selected
manual setting.

3-6
Automatic Operation
When the system is set for AUTO, your climate control
system will control the air delivery mode, fan speed,
A/C and RECIRC operations. Air will come from
the floor, panel or windshield outlets. The fan speed
will vary as the system maintains the selected
temperature setting.
When AUTO is selected, the A/C operation and air inlet
will be automatically controlled. The air conditioning
compressor will run at outside temperatures over
approximately 40
F (4
C). The air inlet will normally
be set to outside air. If it's hot outside, the air inlet will
automatically switch to recirculated inside air to help
quickly cool down your vehicle.
To find your comfort zone, start with 75
F (24
C)
temperature setting and allow about 20 minutes for the
system to regulate. Turn the TEMP knob up or down to
adjust the temperature setting if necessary. If you choose
the temperature setting of 60
F (15
C), the system will
remain at the maximum cooling setting and fan speed.
If you choose the temperature setting of 90
F (33
C),
the system will remain at the maximum heat setting and
fan speed. Choosing either maximum setting will not
cause the system to heat or cool any faster.Be careful not to cover the sensor located on the top of
the instrument panel near the windshield. This sensor
regulates temperature based on sun load.
The EXT (exterior) temperature sensor is located in the
front of the vehicle behind the grille. The displayed
temperature is most accurate after the vehicle has been
moving for a few minutes. If the vehicle is stopped and
then restarted within 2 1/2 hours, the sensor will be hot
from the engine heat. In this case, the temperature first
displayed will continue to be the previous temperature.
The display will update after the vehicle has been
moving for a few minutes and the sensor has a chance
to cool down to the actual temperature.
To avoid blowing cold air in cold weather, the system
will delay turning on the fan until warm air is available.
The length of delay depends on engine coolant
temperature. Pushing the fan button will override this
delay and change the fan to a selected speed.

3-7
Manual Operation
You may also manually adjust the air delivery mode or
fan speed.
FLOOR: Manually selecting FLOOR mode by
cycling through the MODE settings will deliver air to
the floor outlets.
DEFOG: Manually selecting DEFOG by cycling
through the MODE settings will deliver air to the floor
and windshield outlets.
BI-LEVEL: Manually selecting BI-LEVEL
by cycling through the MODE settings will deliver
warm air to the floor and cooler air to the instrument
panel outlets.
PANEL: Manually selecting PANEL by cycling
through the MODE setting will deliver air to the
instrument panel outlets.
DRIVER PUSH OFF: Press this knob to turn the
system off. Some fresh air will continue to flow through
the vehicle from the FLOOR outlets, and the system will
try to maintain the previously chosen comfort setting.PASSENGER PUSH OFF: Press this knob to cancel
the passenger's set temperature. The passenger's set
temperature will be set equal to the driver's set
temperature. Both the words DRIVER and PASS will be
displayed under the set temperature in the display area.
A/C: Press this button to turn the air conditioning
compressor on and off. When A/C is selected or in
AUTO mode, the system will run the A/C automatically
to cool and dehumidify the air inside the vehicle. If you
select A/C OFF while in FRONT defrost, the A/C OFF
text will flash to let you know this is not allowed. This is
to prevent fogging.
RECIRC: Press this button to limit the amount
of outside air entering your vehicle. You may use this
setting to limit odors entering your vehicle. Press
RECIRC to recirculate inside air until the RECIRC
button is pressed again or the OUTSIDE AIR button
is pressed.
If you select RECIRC while in defrost the RECIRC light
will flash to let you know this is not allowed. This is to
prevent fogging.

3-12
Ventilation Tips

Keep the hood and front air inlet free of ice, snow or
any other obstruction such as leaves. The heater and
defroster will work better, reducing the chance of
fogging your windows.

In cool damp weather, minimize your use of
RECIRC to reduce the chance of fogging
your windows.

When you enter a vehicle with the standard system
in cold weather, select FLOOR mode to supply air
through the floor outlets. Then turn the fan on high
for a few moments before driving away. This will
blow moist air from the intake outlets toward the
floor, not the windshield. It reduces the chance of
fogging your windows. If you have the electronic
system, the AUTO setting will do this for you.
Manual operation of the electronic system in the
FLOOR mode will also supply air through the
floor outlets.

Keep the air path under the front seats clear of
objects. This helps air to circulate throughout
your vehicle.Audio Systems
Your audio system has been designed to operate easily
and give years of listening pleasure. You will get the
most enjoyment out of it if you acquaint yourself with it
first. Find out what your audio system can do and how
to operate all its controls, to be sure you're getting the
most out of the advanced engineering that went into it.
Setting the Clock for Systems with Radio
Data System
Press and hold HR until the correct hour appears. AM
will appear on the display for morning hours. Press and
hold MIN until the correct minute appears. The clock
may be set with the ignition on or off.
To set the clock to the time of a station broadcasting
Radio Data System (RDS) information, press and hold
HR and MIN at the same time until TIME UPDATED
appears on the display. If the time is not available
from the station, NO UPDATE will appear on the
display instead.

3-13 AM-FM Stereo with Cassette Tape Player
with Programmable Equalization and
Radio Data System (RDS) (If Equipped)
Playing the Radio
PWR
-VOL: Press this knob to turn the system on
and off. To increase volume, turn the knob clockwise.
Turn it counterclockwise to decrease volume.SCV: Your system has a feature called
Speed
-Compensated Volume (SCV). With SCV,
your audio system adjusts automatically to make up
for road and wind noise as you drive. Set the volume
at the desired level. Press this button to select MIN,
MED or MAX. Each choice allows for more volume
compensation at faster vehicle speeds. Then, as you
drive, SCV automatically increases the volume, as
necessary, to overcome noise at any particular speed.
The volume level should always sound the same to you
as you drive. If you don't want to use SCV, select OFF.
Finding a Station
AM
-FM: Press this button to switch between AM,
FM1 and FM2. The display shows your selection.
TUNE: Turn this knob to choose radio stations.
SEEK: Press the up or down arrow to go to the next
higher or lower station and stay there. The sound will
mute while seeking.

3-14
SCAN: Press and hold one of the SEEK arrows for two
seconds until the SCAN icon appears on the display and
you hear a beep. Use SCAN to listen to stations for a
few seconds. The radio will go to a station, stop for a
few seconds, then go on to the next station. Press one of
the SEEK arrows again to stop scanning. The sound will
mute while scanning.
PUSHBUTTONS: The six numbered pushbuttons let
you return to your favorite stations. You can set up to
18 stations (six AM, six FM1 and six FM2). Just:
1. Turn the radio on.
2. Press AM
-FM to select the band.
3. Tune in the desired station.
4. Press EQ to select the desired equalization.
5. Press and hold one of the six numbered buttons until
you hear a beep. Whenever you press that numbered
button, the station you set will return and the
equalization that you selected will also be
automatically selected for that button.
6. Repeat the steps for each pushbutton.PRESET SCAN: Press and hold one of the SEEK
arrows for more than four seconds until the PSCAN icon
and the preset number appear on the display. You will
hear a double beep. Use PRESET SCAN to listen to
each of your preset stations for a few seconds. The
radio will go to the first preset station stored on your
pushbuttons, stop for a few seconds, then go on to the
next preset station. Press one of the SEEK arrows again
to stop scanning presets.
Note that PRESET SCAN will skip over presets where
no station is being received at that time to prevent
hearing static.
Setting the Tone
TONE: Press and release this button until the desired
tone control (BASS, MID or TREB) is found. The
SELECT LED indicator will light to show that the tone
control can be adjusted. When using BASS, MID or
TREB, turn the SELECT knob clockwise to increase.
Turn it counterclockwise to decrease. If a station is weak
or noisy, you may want to decrease the treble.
Pressing and holding the TONE button for at least two
seconds will return all tone settings to flat regardless of
tone selected. FLAT will appear on the display.

3-15
EQ: This feature allows you to choose preset bass,
mid and treble equalization settings designed for
different individual listening tastes. Press EQ to select
the desired preset equalization setting. Each time you
press EQ, another setting will appear on the display.
You can preset up to six equalization settings. Just:
1. Turn the radio on.
2. Use the TONE button and the SELECT knob to
select the desired equalization.
3. Press and hold EQ for two seconds. SELECT EQ #
will appear on the display. The EQ icon will flash.
4. Press EQ or turn the SELECT knob to select the
desired EQ number. Each time you press EQ or turn
the SELECT knob, another EQ setting will appear on
the display.
5. Press and hold the EQ button or push the SELECT
knob to store the equalization preset. You will hear a
beep and EQ SAVED will appear on the display.
6. Repeat the steps for each EQ setting.
Note that EQ 5 has been programmed for use with talk
radio, but it can be preset to a different tone.Using RDS Mode
Your audio system is equipped with a Radio Data
System (RDS). RDS mode gives you many useful new
features. With RDS, the radio can:

Seek only to stations with the types of programs you
want to listen to,

seek to stations with traffic announcements,

receive announcements concerning local and
national emergencies, and

receive and display messages from radio stations.
RDS features are only available for use on FM stations
which broadcast RDS information. The RDS features of
your radio rely upon receiving specific RDS information
from these stations. These features will only work when
the RDS information is available. In rare cases, a radio
station may broadcast incorrect information that will
cause the radio features to work improperly. If this
happens, please contact the radio station.
When you are tuned to an RDS station, the station
name will appear on the display, instead of the
frequency. Most RDS stations provide their station
name, the time of day and a Program Type (PTY) for
their current programming.

3-16
TRAF: Press this button to receive traffic
announcements. The traffic announcement brackets will
appear on the display. TRAF will appear on the display
if the tuned station broadcasts traffic announcements.
If the current tuned station does not broadcast traffic
announcements, the radio will seek to a station that
does. When the radio finds a station that broadcasts
traffic announcements, it will stop. If no station is found,
NO TRAFFIC will appear on the display.
When a traffic announcement comes on the tuned radio
station or a related network station, you will hear it,
even if the volume is muted or a cassette tape or
compact disc is playing. If the cassette tape or compact
disc player was being used, the tape or compact disc will
stay in the player and resume play at the point where
it stopped.
INFO: If the current station has a message, INFO will
appear on the display. Press this button to see the
message. If the whole message does not appear on the
display, parts of the message will appear every three
seconds until the message is completed. To see the parts
of the message faster than every three seconds, press this
button again. A new group of words will appear on the
display. Once the complete message has been displayed,
INFO will disappear from the display until another new
message is received.PROG-TYPE: This button is used to turn on and off
Program Type (PTY) select. The P
-TYPE icon will
appear on the display and the SELECT LED indicator
next to the SELECT knob will light. The last selected
PTY will appear on the display for five seconds. Turn
the SELECT knob to select the PTY you want to listen
to. Press SEEK or SCAN to find radio stations of the
PTY you want to listen to. The last PTY selected will
be used for seek or scan modes. If a station with the
selected PTY is not found, NOT FOUND will appear on
the display. If both PROG
-TYPE and TRAF are on, the
radio will search for stations with traffic announcements
and the selected PTY.
To use the PROG
-TYPE interrupt feature, press and
hold this button until you hear a beep on the PTY
you want to interrupt. An ª*º will appear next to the
PTY name, for example CLASSICAL*. When you are
listening to a cassette or compact disc, the last selected
RDS FM station will interrupt play if that selected PTY
format is broadcast.

3-17
PUSHBUTTONS: The six numbered pushbuttons let
you return to your favorite Program Types (PTYs).
These buttons have factory PTY presets. You can set up
to 12 PTYs (six FM1 and six FM2). Just:
1. Press PROG
-TYPE, if it is not already on.
2. Press AM
-FM to select FM1 or FM2.
3. Turn the SELECT knob to select a PROG
-TYPE.
4. Press and hold one of the six numbered buttons until
you hear a beep. Whenever you press that numbered
button, the PTY you set will return.
5. Repeat the steps for each pushbutton.
ALERT!: This type of announcement warns of national
or local emergencies. You will not be able to turn off
alert announcements. ALERT! appears on the display
when an alert announcement plays. When an alert
announcement comes on the tuned radio station, you
will hear it, even if the volume is muted or a cassette
tape or compact disc is playing. If the cassette tape or
compact disc player is playing, play will stop for the
announcement and resume when the announcement
is finished.ALTERNATE FREQUENCY: This feature allows
the radio to switch to a stronger station with the same
program type. Press and hold AM
-FM for two seconds
to turn alternate frequency on. AF ON will appear on the
display. The radio may switch to stronger stations. Press
and hold AM
-FM again for two seconds to turn alternate
frequency off. AF OFF will appear on the display. The
radio will not switch to other stations.
Adjusting the Speakers
BAL
-FADE: This button adjusts balance and fade.
To adjust balance, press this button until BAL appears
on the display. Turn the SELECT knob clockwise for
the right speakers and counterclockwise for the left
speakers. The middle position balances the sound
between the speakers. To adjust fade, press this button
until FAD appears on the display. Turn the SELECT
knob clockwise to adjust the sound to the front speakers
and counterclockwise for the rear speakers. The middle
position balances the sound between the speakers. Press
and hold this button for two seconds to return both fade
and balance to the middle position.

3-18
Playing a Cassette Tape
Your tape player is built to work best with tapes that are
up to 30 to 45 minutes long on each side. Tapes longer
than that are so thin they may not work well in this
player. The longer side with the tape visible should face
out. If the ignition is on, but the radio is off, the tape can
be inserted and will begin playing. If you hear nothing
but a garbled sound, the tape may not be in squarely.
Press EJECT to remove the tape and start over.
While the tape is playing, use the VOL, FAD, BAL,
TREB, MID, BASS, EQ, SEEK and SCAN controls just
as you do for the radio. The display will show TAPE and
an arrow showing which side of the tape is playing. The
tape player automatically begins playing the other side
when it reaches the end of the tape.
Your tape bias is set automatically when a metal or
chrome tape is inserted. If you want to insert a tape
when the ignition is off, first press EJECT or the
RCL knob.
If an error appears on the radio display, the tape won't
play because of an error.TIGHT TAPE is displayed when the tape is tight and the
player can't turn the tape hubs. Remove the tape. Hold
the tape with the open end down and try to turn the right
hub counterclockwise with a pencil. Turn the tape over
and repeat. If the hubs do not turn easily, your tape may
be damaged and should not be used in the player. Try a
new tape to make sure your player is working properly.
BROKEN TAPE is displayed when the tape is broken.
Try a new tape.
WRAPPED TAPE is displayed when the tape is
wrapped around the tape head. Attempt to get the
cassette out. Try a new tape.
If any error occurs repeatedly or if an error can't be
corrected, please contact your dealer. If your radio
displays an error message, write it down and provide it
to your dealer when reporting the problem.
FWD (1): Press this button to advance quickly to
another part of the tape. Press the button again to return
to play. The radio will play the last selected station
while the tape advances. You may select stations during
FWD operation by using TUNE.
While in FWD mode the display will show FREQ and
FWD

. If the radio is playing a RDS station the
display will only show FREQ.