brake light PONTIAC FIREBIRD 1994 User Guide

Features and Controls
Fuel Gage
four fuel gage shows about how much
bel is in your tank. The fuel gage works
mly when the ignition switch is in the
‘Run” position. When the gage pointer
‘Irst indicates
“E,” you still have a little
uel left (about one to two gallons), but
IOU need to get more right away.
3ere are four concerns some owners
lave had about the fuel gage. All these
iituations are normal and do not indicate
:hat anything is wrong with the fuel gage.
,..go
At the gas station, the gas pump shuts
off before the gage reads “E”
It takes more (or less) gas to fill up
than the gage reads. For example, the
gage reads
1/2 full, but it took more
(or less) than half of the tank’s
capacity to fill it.
The gage moves
a little when you
turn, stop or speed up.
When you turn the engine
off, the
gage doesn’t go back to
“E.”
Brake System Warning Light
Your Pontiac’s hydraulic brake system is
divided into two parts. If one part isn’t
working, the
other part can still work and
stop you. For good braking, though, you
need both pws working well.
If the warning light comes on, there could
be a brake problem. Have your brake
system inspected right away.
This light should come on as you start the
vehicle. If it doesn’t come on then, have
it
fixed so it will be ready to warn you if
there’s a problem.
ProCarManuals.com

If the light comes on while you are driving, pull
off the road and stop
carefully.
You may notice that the pedal is
harder to push. Or, the pedal may
go
closer to the floor. It may take longer to
stop. If the light is still on,
or if the
anti-lock brake system warning light is
flashing, have the vehicle towed for
service. (See “Anti-Lock Brake System
Warning Light” and “Towing Your
Vehicle” in
the Index.) The brake
system warning light will also
come on when you set your parlung
brake, and it will stay on if your parking
brake doesn’t release fully. If
it stays on
after your parking brake
is fully released,
it means
you have a brake problem.
Anti-Lock Brake System Warning
Light
With anti-lock, this light will come on
when you start your engine and it will
stay on for three seconds. That’s normal.
If the light doesn’t come on, have it fixed
so it will be ready to warn you if there is a
problem.
If the light flashes when you’re driving,
you don’t have anti-lock brakes and
there’s a problem with your regular
brakes. Pull
off the road and stop
carefully.
You may notice that the pedal is
harder to push. Or, the pedal may go
closer to the floor. It may take longer to
stop. Have the vehicle towed for service.
(See “Towing
Your Vehicle” in the
Index.)
91 ...
ProCarManuals.com

Features and Controls
-
I
1:
4
i;
S
S
1
S
C
s
C
S
1
t
... 92
ABS
INOP
f the anti-lock brake system warning
ight stays on longer than normal after
rou’ve started your engine, turn the
gnition
off. Or, if the light comes on and
tays on when you’re driving, stop as
oon as possible and turn the ignition
off.
rhen start the engine again to reset the
‘ystem. If the light still stays on, or
:omed on again while you’re driving,
rour Pontiac needs service. If the light is
In but not flashing and the regular brake
,ystem warning light isn’t on, you still
lave brakes, but you don’t have anti-lock
wakes.
TCS
OFF
kaction Control System Warning
,ight (Option)
men the traction control system is off,
he “TCS OFF” light will come on. This
ight will also come on for three seconds
:ach time you start your vehicle as a bulb
:heck and if there’s a system failure. See
‘Traction Control System” in the Index.
The traction control system will shut
lown partially due to brake overheating
)ut the “TCS OFF” light will not come
m. If there is throttle relaxer overheating,
he “TCS
OFF” light will illuminate
md the system will shut down. Once
werything cools
off, the system will
)perate normally again.
ProCarManuals.com

When this warning light is on, the system
will not limit wheel spin. Adjust your
driving accordingly.
Low Traction Light
When your anti-lock system is adjusting
brake pressure to help avoid a braking
skid, the “LOW TRAC” light will appear
on your instrument cluster. If you have
the traction control system, this light will
also come on when the system is limiting
wheel spin. Slippery road conditions may
exist if this light comes on,
so adjust your
driving accordingly. The light will stay
or
for a few seconds after the anti-lock
system stops adjusting brake pressure or
the traction control system stops limiting
wheel spin. The “LOW TRAC” light also
comes
on briefly, as a bulb check, when
the engine is started.
Sngine Coolant Temperature Gage
’his gage shows the engine coolant
emperature.
If the gage pointer moves
nto the red area, your engine is too, hot!
t means that your engine coolant fias
werheated. If you have been operiting
‘our vehicle under normal driving-
onditions, you should pull off the road,
top your vehicle and turn
off the engine
s soon as possible.
IOT COOLANT CAN BURN
YOU
iADLY!
n “Problems on the Road,” this manual
hows what
to do. See “Engine
Iverheating” in the Index.
93 ...
ProCarManuals.com

Features and Controls
I
Voltmeter
You can read battery voltage on your
voltmeter.
If it reads less than 11 volts or
more than
16 volts while your engine is
running, and it stays there, you may have
a problem with the electrical charging
system. Have it checked right away.
Driving with the voltmeter reading in a
warning zone could drain your battery.
If you idle your engine for a while, the
voltmeter reading might move into the
yellow zone.
If the reading stays in the
yellow zone while you are driving, you
may have a problem with the electrical
charging system. Have it checked. While
the voltmeter reads in the yellow zone,
your battery may not be able
to power
certain electrical accessories, like
ABS.
... 94
:If this happens, your “ABS INOP’ light
will come on. See “Anti-Lock Brake
System Warning Light” in this
part.)
[f you must drive a short distance with the
voltmeter reading in a warning zone, turn
~ff all your accessories, including your
:omfort control and audio systems.
Malfunction Indicator Lamp
(Service Engine Soon Light)
A computer monitors operation of your
fuel, ignition and emission control
systems. This light should come on when
the ignition is on, but the engine is not
running, as a check to show you it is
working.
If it doesnot come on at all,
have it fixed right away.
If it stays on, or
it comes on while you are driving, the
computer is indicating that you have a
problem. You should take your vehicle in
for service soon.
ProCarManuals.com

This is a mistake. Your brakes may not
have time to cool between hard stops. Your brakes will wear out much faster if
you do a lot of heavy braking. If you
keep pace with the traffic and allow
realistic following distances, you will
eliminate a lot of unnecessary braking.
That means better braking and longer
brake life.
If your engine ever stops while you’re
driving, brake normally but don’t pump
your brakes. If you do, the pedal may get
harder to push down. If your engine stops,
you will still have some power brake
assist. But you will use it when you brake.
Once the power assist
is used up, it make
take longer to stop and the brake pedal
will be harder to push.
mti-Lock Brakes (ABS)
[our Pontiac has an advanced electronic
lraking system that will help prevent
kidding.
ABS
INOP
This light on the instrument panel will go
on when you start your vehicle.
When you start your vehicle, or when you
begin to drive away, you may hear a
momentary motor or clicking noise. And
you may even notice that
your brake
pedal moves a little while
this is going on.
This is the
ABS system testing itself. If
there’s a problem with the anti-lock brake
system, the anti-lack brake system
warning light will stay on or flash.
129 ...
ProCarManuals.com

Your Driving and the Road
Here’s how anti-lock works. Let’s say
the road is wet. You’re driving safely.
Suddenly an animal jumps out in front
You slam on the brakes. Here’s what
happens with ABS.
A computer senses that wheels are
slowing down. If one of the wheels is
about to stop rolling, the computer will
separately work the brakes at each front
wheel and at the rear wheels.
The anti-lock system can change the
brake pressure faster than any driver
could. The computer is programmed to
make the most of available tire and road
conditions.
of you.
. . .I30
You can steer around the obstacle while
braking hard.
As you brake, your computer keeps
receiving updates
on wheel speed and
controls braking pressure accordingly.
Remember: Anti-lock doesn’t change the
time you need to get your foot
up to the
brake pedal. If you get too close to the vehicle
in front of you, you won’t have
time to apply your brakes if that vehicle
suddenly slows or stops. Always leave
enough room up ahead to stop, even
though you have anti-lock brakes.
To Use Anti-Lock
Don’t pump the brakes. Just hold the
brake pedal down and let anti-lock work for
you. You may feel the system
working, or you may notice some noise,
but this is normal. When your anti-lock system is adjusting brake pressure to help
avoid a braking skid, the “LOW TRAC”
light will come on. See “Low Traction
Light” in the Index.
Traction Control System (Option: LT1
V8 Engine)
Your vehicle may have a traction control
system that limits wheel spin. This is
especially useful in slippery road
conditions. The system operates only
if
it
senses that one or both of the rear wheels
are spinning or beginning to lose traction.
When this happens, the system works the
rear brakes and reduces engine power (by
closing the throttle and managing spark)
to limit wheel spin.
The “LOW TRAC” light will come on
when your traction control system is
limiting wheel spin. See “Low Traction Light” in the Index.
You may feel the
system working, or you may notice some
noise, but this is normal.
The traction control system may operate
on dry roads under some conditions, and
you may notice a reduction
in acceleration
when this happens. This is normal and
doesn’t mean there’s a problem with your vehicle. Examples of these conditions
include a hard acceleration in a turn, or
an abrupt upshift or downshift.
ProCarManuals.com

Your Driving and the Road
Passing
The driver of a vehicle about to pass
another on a two-lane highway waits for
just the right moment, accelerates, moves
around the vehicle ahead, then goes back
into the right lane again. A simple
maneuver?
Not necessarily! Passing another vehicle
on a two-lane highway is a potentially
dangerous move, since the passing
vehicle occupies the same lane as
oncoming traffic for several seconds.
A
miscalculation, an error in judgment, or a
brief surrender to frustration or anger can
suddenly put the passing driver face to
face with the worst of all traffic accidents
- the head-on collision.
So here are some tips for passing:
“Drive ahead.” Look down the road,
to the sides, and to crossroads for
situations that might affect your
passing patterns. If you have any
doubt whatsoever about making a
successful pass, wait for a better time.
Watch for traffic signs, pavement
markings, and lines. If you can see a
sign up ahead that might indicate a
turn or an intersection, delay your
pass.
A broken center line usually indicates
it’s all right to pass
(providing the road ahead is clear).
Never cross a solid line
on your side
of the lane or a double solid line, even
if the road seems empty of
approaching traffic.
Do not get too close to the vehicle you
want to pass while you’re awaiting an
opportunity. For one thing, following
too closely reduces your area of
vision, especially if you’re following a
larger vehicle. Also, you won’t have
adequate space if the vehicle ahead
suddenly slows or stops. Keep back a
reasonable distance.
When it looks like a chance to pass is
coming up, start to accelerate but stay
in the right lane and don’t get too
close. Time your move
so you will be
increasing speed as the time comes to
move into the other lane. If the way is
clear to pass, you will have a “running
start” that more than makes up for the
distance you would lose by dropping
back. And if something happens to
cause you to cancel your pass, you
need only slow down and drop back
again and wait for another
opportunity. 0
0
0
If other cars are lined up to pass a
slow vehicle, wait your turn. But take
care that someone isn’t trying to pass
you as you pull out to pass the slow
vehicle. Remember to glance over
your shoulder and check the blind spot.
Check your mirrors, glance over your
shoulder, and start your left lane
change signal before moving out of
the right lane to pass. When you are
far enough ahead of the passed vehicle
to see its front in your inside mirror,
activate your right lane change signal
and move back into the right lane. (Remember that your right outside
mirror is convex. The vehicle you just
passed may seem to be farther away
from you than it really is.)
Try not to pass more than one vehicle
at a time on two-lane roads. Reconsider
before passing the next vehicle.
Don’t overtake a slowly moving
vehicle too rapidly. Even though the
brake lights are not flashing, it may be
slowing down or starting to turn.
If you’re being passed, make it easy
for the following driver
to get ahead
of you. Perhaps you can ease
a little to
the right.
. . .I34
ProCarManuals.com

Hitches
It’s important to have the correct hitch
equipment. Crosswinds, large trucks
going by, and rough roads are a few
reasons why you’ll need the right hitch.
Here are some rules to follow:
0
0
Will you have to make any holes in
the body of your vehicle when you
install a trailer hitch? If you do, then
be sure to seal the holes later when
you remove the hitch. If you don’t
seal them, deadly carbon monoxide
(CO) from your exhaust can get into
your vehicle (see “Carbon Monoxide”
in the Index). Dirt and water can,
too.
The bumpers on your vehicle are not
intended for hitches.
Do not attach
rental hitches or other bumper-type
hitches to them. Use only a
frame-mounted hitch that does not
attach to the bumper.
Safety Chains
You should always attach chains between
your vehicle and your trailer. Cross the
safety chains under the tongue of the
trailer
so that the tongue will not drop to
the road if it becomes separated from the
hitch. Instructions about safety chains
may be provided by the hitch manufacturer or
by the trailer
, 1.
manufacturer. Follow the manufacturer’s
recommendation for attaching safety
chains. Always leave just enough slack
so
you can turn with your rig. And, never
allow safety chains to drag on the ground.
Trailer Brakes
If your trailer weighs more than 1,000
pounds (450 kg) loaded, then it needs its
own brakes
- and they must be adequate.
Be sure to read and follow the instructions
for the trailer brakes
so you’ll be able to
install, adjust and maintain them properly.
Because you have anti-lock brakes, do not
try to tap into your vehicle’s brake
system. If
YOU do, both brake systems
won’t work well, or at all.
Driving with a Trailer
Towing a trailer requires a certain amount
of experience. Before setting out for the
open road, you’ll want to get to know
your rig. Acquaint yourself with the feel
of handling and braking with the added
weight
of the trailer. And always keep in
mind that ’the vehicle you are driving is
now a good deal longer and not nearly as
responsive
as your vehicle is by itself. Before you
start, check the trailer hitch
and platform, safety chains, electrical
connector, lights, tires and mirror
adjustment. If
the trailer has electric
brakes,
start your vehicle and trailer
moving and then apply the trailer brake
controller by hand to be sure the brakes
are working. This lets you check your
electrical connection at the same time.
During your trip, check occasionally to
be sure that the load is secure,. and that
the lights and any trailer brakes are still
working.
Following Distance
Stay at least twice as far behind the
vehicle ahead as you would when driving
your vehicle without a trailer.,,This can
help
you avoid situations that’.require
heavy braking and sudden turns.
Passing
You’ll need more passing distance up
ahead when you’re towing a trailer. And,
because you’re a good deal longer, you’ll
need to go much farther beyond the
passed vehicle before you can return to
your lane.
147 ...
ProCarManuals.com

Your Driving and the Road
Backing Up
Hold the bottom of the steering wheel
with one hand. Then, to move the trailer
to the left, just move that hand to the left.
To move the trailer to the right, move
your hand to the right. Always back up
slowly and, if possible, have someone
guide you.
Making 7hms
When you’re turning with a trailer, make
wider turns than normal.
Do this so your
trailer won’t strike soft shoulders, curbs,
road signs, trees, or other objects. Avoid
jerky or sudden maneuvers. Signal well in
advance.
Thrn Signals When Towing a Trailer
When you tow a trailer, your vehicle has
to have a different turn signal flasher and
extra wiring. The green arrows on your
instrument panel will flash whenever you signal a turn or lane change. Properly
hooked up, the trailer lights will also
flash, telling other drivers you’re about to
turn, change lanes or stop. When
towing a trailer, the green arrows
on your instrument panel will flash for
turns even
if the bulbs on the trailer are
burned out. Thus, you may think drivers
behind you are seeing your signal when
they are not. It’s important to check
occasionally to be sure the trailer bulbs
are still working.
Driving on Grades
Reduce speed and shift to a lower gear
before you start down a long or steep
downgrade. If you don’t shift down, you
might have to use your brakes
so much
that they would get hot and no longer
work well.
On a long uphill grade, shift down and
reduce your speed to around
45 mph
(70 km/h) to reduce the possibility of
engine and transmission overheating.
If you are towing a trailer and you
have an automatic transmission with
Overdrive, you may prefer to drive in
“D”
instead of Overdrive (or, as you need to, a
lower gear). Or,
if you have a manual
transmission with fifth (or sixth) gear and
you are towing a trailer, it’s better not to
use fifth (or sixth) gear. Just drive in
fourth gear (fifth gear if you have a six-speed manual transmission) or, as you
need to, a lower gear.
Parking on Hills
You really should not park your vehicle,
with a trailer attached, on a hill. If
-
something goes wrong, your rig could
start to move. People can be injured, and
both your vehicle and the trailer can be
damaged.
But if you ever have to park your rig on a
hill, here’s how to do it:
1. Apply your regular brakes, but don’t
shift into
“P” (Park) yet, or into gear
for a manual transmission.
2. Have someone place chxks under the
3. When the wheel chocks are in place,
release the regular brakes until the
chocks absorb the load. trailer wheels.
4. Reapply the regular brakes. Then
apply your parking brake, and then shift to
“P” (Park), or “R” (Reverse)
for a manual transmission.
5. Release the regular brakes.
. . .I48
ProCarManuals.com