light PONTIAC FIREBIRD 1994 User Guide

Features and Controls
NOTICE:
If you put things in the hatchback
area, be sure they won’t break the
glass when you close it. Never slam
.the hatch down. You could break the
glass or damage the defogger grid
(if equipped).
Theft
Vehicle theft is big business, especially in
some cities. Although your Pontiac has a
number of theft-deterrent features, we
know that nothing we put on it can make
it impossible to steal. However, there are
ways you can help.
Key in the ignition: If you walk away
from your vehcle with the keys inside,
it’s an easy target for joy riders or
professional thieves
- so don’t do it.
When you park your Pontiac and open
the driver’s door, ydu’ll heai a tone
reminding you to remove your key from
the ignition and take it with you, Always
do this. Your steering wheel will be
locked, and
so will your ignition. If you
have an automatic transmission, taking your key out also locks your transmission.
And remember to lock the doors.
Parking at Night: Park in a lighted spot,
close all windows and lock your vehicle.
Remember to keep your valuables out of
sight. Put
them in a storage area, or take
them with you.
... 48
ProCarManuals.com

Features and Controls
I rl SECUIITY
The ignition key must be clean and dry
before it’s inserted in the ignition or the
engine may not start. If the engine does
not start and the “SECURITY” light stays on when you
try to start the vehicle, the
key may be dirty or wet. Turn the
ignition
off.
Clean and dry the key. Wait about three
minutes and try again. The security light
will remain on during this time. If the
starter still won’t work, and the key
appears to be clean and
dry, wait about
three minutes and try another ignition key.
At this time, you may also want
to check
the fuses (see “Fuses and Circuit
Breakers” in the Index). If the starter
won’t work with the other key, your
vehicle needs service.
If your vehicle
does start, the first ignition key may be
... 50
Faulty. See your Pontiac dealer or a
locksmith who can service the
PASS-Key@II.
[f you accidentally use a key that has a
Jamaged or missing resistor pellet, the
starter won’t work and the security light
will flash. But you don’t have to wait
three minutes before trying another
ignition key.
See your Pontiac dealer or a locksmith
who can service the PASS-Key@II to
have a new key made.
If you’re ever driving and the
“SECURITY’’ light comes on and stays
on, you will be able to restart your engine
if you turn it
off. Your PASS-Key@ I1
system, however, is not working properly
and must be serviced by your Pontiac
dealer. Your vehicle is not protected by
the PASS-Key% system.
If you lose or damage a PASS-Key@ I1
ignition key, see your Pontiac
dealer or a locksmith who can service
PASS-Key% to have a new key made.
In
an emergency, call the Pontiac Roadside
Assistance Program on
1-800-ROADSIDE
or 1-800-762-3743.
New Vehicle
“Break-Zn”
NOTICE:
Your modem Pontiac doesn’t need an
elaborate “break-in.” But it will per-
form better in the long run if you fol-
low these guidelines:
Keep your speed at
55 mph (88
km/h) or less for the first 500
miles (804 km).
Don’t drive at any one speed
-
fast or slow - for the first 500
miles (804 km). Don’t make
full-throttle starts.
Avoid malung hard stops for the
first 200 miles (322 km) or
so.
During this time your new brake linings aren’t yet broken in. Hard
stops with new linings can mean
premature wear and earlier
replacement. Follow this
“brealung-in” guideline every
time you get new brake linings.
ProCarManuals.com

D
Ignition Switch
With the ignition key in the ignition
switch, you can
turn the switch to five
positions:
Acc (A): Position in which you can
operate your electrical power accessories.
Press in the ignition switch as you
turn
the top of it toward you.
LOCK (B): The only position in which
you can remove the key. This locks your
steering wheel, ignition and automatic
transmission.
If you have an automatic transmission,
tht
ignition switch can’t be turned to
“LOCK’ unless the shift lever is in the
“P’ (Park) position.
Off (C): Unlocks the steering wheel,
ignition and automatic transmission, but
does not send electrical power to any
accessories. Use this position if your
vehicle must be pushed or towed. A
warning tone will sound if you open the
driver’s door when the ignition is in
“Off”
and the key is in the ignition.
Run (D): Position to which the switch
returns after you start your engine and
release the switch. The switch stays in the
“Run” position when the engine is
running. But even when the engine is not
running, you can use “Run” to operate
your electrical power accessories and to
display some instrument panel warning
and indicator lights.
Start (E): Starts the engine. When the
engine starts, release the key. The ignition
switch will return to “Run” for normal
driving.
Note that even if the engine is not
running, “Acc” and “Run” allow you to
operate your electrical accessories, such
as the radio and ventilation fan.
:I
Ley Release Button: If you have a
lanual transmission, your ignition lock
as a key release button.
You must press
le button before you can take your key
ut of the ignition lock.
51 . .
ProCarManuals.com

Features and Controls
When starting your engine in very cold
weather (below 0°F or
- 18”C), do this:
1.
2.
With your foot off the accelerator
pedal, turn the ignition key to “Start”
and hold it there. When the engine
starts, let go of the key. Use the
accelerator pedal to maintain engine
speed, if you have to, until your
engine has
run for a while.
If your engine still won’t start (or
starts but then stops), it could be
flooded with too much gasoline.
Try
pushing your accelerator pedal all the
way to the floor and holding it there
as you hold the key
in “Start” for
about three seconds. If the vehicle
starts briefly but then stops again, do
the same thing, but this time keep the
pedal down for five or six seconds.
This clears
the extra gasoline from
the engine.
NOTICE:
Your engine is designed to work with
the electronics in your vehicle. If you
add electrical parts or accessories,
you could change the way
the fuel
injection system operates. Before
adding electrical equipment, check
with your dealer. If you don’t, your
engine might not perform properly.
If you
ever have to have your vehicle
towed, see the part of this manual
that tells how to do it without
damaging your vehicle. See “Towing
Your Vehicle” in the Index.
Driving through Deep
Standing Water
NOTICE:
If you drive too quickly through deep
puddles or standing water, water can
come in through your engine’s air
intake and badly damage your
engine. If you can’t avoid deep
puddles or standing water, drive
through them very slowly.
Performance Mode Switch
(Option)
This switch lets you change from a
normal driving mode to a performance
mode. When you start the engine, the switch will be in normal mode. For
general driving conditions, use the
normal mode. It will remain
in normal
unless you select the “PERFORM”
feature.
For a firmer shift and increased
performance, you may choose the
“PERFORM, mode. The light in the
center
of the switch will light up when
selected. The switch will then remain in
“PERFORMANCE’ mode until the
engine is shut off, when it will go back to
normal mode.
... 54
ProCarManuals.com

Your six-speed manual transmission
has a feature that allows you to safely
shift into
“R’ (Reverse) while the vehicle
is rolling (at less than 3 mph). You will be
“locked-out” if you try to shift into “R”
(Reverse) while your vehicle is’ moving
faster than
3 mph.
If you have turned your ignition off and
wish to park your vehicle in Reverse, you
will have to move the shift lever quickly
to the right, “crashing” through the high
load spring and then into gear.
SKIP
SHIFT
;kip Shift Light (5.7L LT1 Engine)
Yhen this light comes on, you can only
hift from
“1” (First) to “4” (Fourth) gear
nstead of “1” (First) to “2” (Second)
gar. This helps you to get
the best
lossible fuel economy.
’his light will come on under these
onditions:
The engine coolant temperature is greater than 170°F (77”C),
You are going
15-20 mph
(24-32
km/h), and
You are
at 35% throttle or less. When this
light
is on, the gear shift lever
will let you shift from
“1” (First) gear to
“4”(Fourth) gears only. Once you are
in
“4” (Fourth) gear, you can press the
clutch again and shift into another gear.
Follow the shift speeds in this chart when
the
“SKIP SHIFT” light is on.
Computer Aided Manual Transmission
Shift Speeds:
1st to 4th. . , . , . . 15 mph (24 km/h)
4th to 5th ...... 25 mph (40 km/h)*
5th
to 6th ...... 40 mph (64 km/h)**
Each time you come to
a stop, the
engine’s Electronic Control Module
(EGM) determines when to activate the
“SKIP SHIFT” upshift system. Use
“2”
(Second) gear only when you accelerate
very quickly from’a stop.
You can then
follow the full gear shift pattern.
*30 mph (48 km/h) when accelerating
to highway speeds.
**45 mph (72 km/h) when accelerating
to highway
speeds.
61 ’. , . ProCarManuals.com

Parking
Parking Brake
The parking brake uses the brakes on the
rear wheels.
To set the parking brake: Hold the brake
pedal down and pull up on the parking brake lever. If the ignition is on, the brake
system warning light will come on.
To release the parking brake: Hold the
brake pedal down.
Pull the parking brake
lever up until you can push in the release
button. Hold the release button in as you
move the brake lever all the way down.
NOTICE:
Driving with the parking brake on
can cause your rear brakes to over-
heat. You may have to replace them,
and you could also damage other
parts of your vehicle.
If you are towing a trailer and are
parking on any hill:
See “Towing a
Trailer” in the Index. That section shows
what to do first to keep the trailer from
moving.
63 ...
ProCarManuals.com

I Tilt Wheel
1 tilt steering wheel allows you to adjust
he steering wheel before you drive.
r'ou can also raise it to the highest level tc
$ve your legs more room when you exit
md enter the vehicle.
?o tilt the wheel, hold the steering wheel
md pull the lever. Move the steering
vheel to a comfortable level, then release
he lever to lock the wheel in place.
I The Turn
Signal'Headlight Beam
Lever
'he lever on the left side of the steering
dumn includes your:
Turn Signal and Lane Change
Indicator
Headlight HigNLow Beam and
Passing Signal
Windshield Wipers
Windshield Washer
Cruise Control (Option)
rurn Signal and Lane Change
ndicator
'he turn signal has two upward '(for
Light) and two downward
(for Left)
lositions. These positions allow
'you to
ignal a turn or a lane change.
b signal a turn, move the lever dl the
day up or down. When the turn is
inished, the lever will return
utomatically.
69 ...
ProCarManuals.com

Features and Controls
A green arrow on the instrument panel
will flash in the direction of the turn or
lane change.
To signal a lane change, just raise or
lower the lever until the green arrow start
to flash. Hold it there until you complete
your lane change. The lever will return b!
itself when you release it.
As you signal a turn or a lane change, if
the arrows don’t flash but just stay on, a
signal bulb may be burned out and other
drivers won’t see your turn signal.
If a bulb is burned out, replace it to help
avoid an accident. If the green arrows
don’t go on at all when you signal a turn,
check the fuse (see “Fuses” in the Index)
and for burned-out bulbs.
feadlight High/Low Beam
’0 change the headlights from low beam
3 high or high to low, pull the turn signal
:ver all the way toward you. Then
:lease it. When the high beams are on,
lis blue light on the instrument panel
lso will be on.
Windshield Wipers
fou control the windshield wipers by
urning the band
with the wiper symbol
In it.
;or a single wiping cycle, turn the band to
‘MIST.” Hold it there until the wipers
;tart, then let go. The wipers will stop
ifter one cycle. If
you want more cycles,
lold the band on “MIST” longer.
You can set the wiper speed for a long or
;hort delay between wipes. This can be
iery useful in light rain or snow. Turn the
>and to choose the delay time. The closer
:o “LO,” the shorter the delay.
... 70
ProCarManuals.com

Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase your
speed. When you take your foot
off the
pedal, your vehicle will slow down to the
Cruise Control speed you set earlier.
Using Cruise Control on Hills
How well your Cruise Control will work
on hills depends upon your speed, load,
and the steepness
of the hills. When going
up steep hills, you may have to step on
the accelerator pedal to maintain your
speed. When going downhill, you may
have to brake or
shift to a lower gear to
keep your speed down.
Of course,
applying the brake takes you out
of
Cruise Control. Many drivers find this to
be too much trouble and don’t use Cruise
Control on steep hills.
ro Get Out of Cruise Control
:here are several ways to turn off the
3ruise Control:
I. Step lightly on the brake pedal or pus1
the clutch pedal, if you have a manual
transmission;
OR
!. Move the Cruise switch to “OFF.”
:o Erase Speed Memory
Yhen you turn off the Cruise Control or
he ignition, your Cruise Control set speec
nemory is erased.
kaction Control System and Cruise
lontrol
f your traction control system engages
vhile your Cruise Control
is set, Cruise
lontrol will disengage. Your speed will
le
set in memory, though. When Cruise
lontrol engages again, use
“WA”
Resume/Accelerate) to go back to your
et speed.
”‘ 1. 2. 4>
fa...
ProCarManuals.com

Features and Controls
Operation of Lights
Although your vehicle’s lighting system
(headlights, parking lights, fog lamps,
side marker lights and taillights) meets
al
applicable federal lighting requirements,
certain states and provinces may apply
their own lighting regulations that may
require special attention before you
operate these lights.
For example, some jurisdictions may
require that you operate your fog lamps
only when your lower beam headlights
are
also on, or that headlights be turned
on whenever
you must use your
windshield wipers. In addition, most
jurisdictions prohibit driving solely with
parking lights, especially at dawn or dusk.
It is recommended that you check with
your own state or provincial highway
authority for applicable lighting
regulations.
Main Light Control
The main light control is a knob that
works these lights:
Headlights
Taillights
Parking lights
License lights
Sidemarker lights
Instrument panel lights
Turn the knob to
-v to turn on your
headlights and okbpoperating lights.
Turn the knob to
p$ to turn on your
parking lights without your headlights.
Turn the knob to “OFF” to turn
off the
lights.
‘I
’
II
Crightness Control
’his switch controls the brightness of
‘our instrument panel lights.
Turn the
witch to brighten or dim the lights. If you
~rn the switch all the way up to .w ,
‘our courtesy lights will come on.
Lights On Reminder
f you turn the ignition “Off’ and leave
he lights on, you will hear a chime when
IOU open the driver’s door.
ieadlight Doors
The headlight doors are designed to open
vhen
you turn the headlights on and close
vhen you turn the headlights off. The
leadlight doors can be opened without
. . .76
ProCarManuals.com