display PONTIAC FIREBIRD 1994 Owners Manual

D
Ignition Switch
With the ignition key in the ignition
switch, you can
turn the switch to five
positions:
Acc (A): Position in which you can
operate your electrical power accessories.
Press in the ignition switch as you
turn
the top of it toward you.
LOCK (B): The only position in which
you can remove the key. This locks your
steering wheel, ignition and automatic
transmission.
If you have an automatic transmission,
tht
ignition switch can’t be turned to
“LOCK’ unless the shift lever is in the
“P’ (Park) position.
Off (C): Unlocks the steering wheel,
ignition and automatic transmission, but
does not send electrical power to any
accessories. Use this position if your
vehicle must be pushed or towed. A
warning tone will sound if you open the
driver’s door when the ignition is in
“Off”
and the key is in the ignition.
Run (D): Position to which the switch
returns after you start your engine and
release the switch. The switch stays in the
“Run” position when the engine is
running. But even when the engine is not
running, you can use “Run” to operate
your electrical power accessories and to
display some instrument panel warning
and indicator lights.
Start (E): Starts the engine. When the
engine starts, release the key. The ignition
switch will return to “Run” for normal
driving.
Note that even if the engine is not
running, “Acc” and “Run” allow you to
operate your electrical accessories, such
as the radio and ventilation fan.
:I
Ley Release Button: If you have a
lanual transmission, your ignition lock
as a key release button.
You must press
le button before you can take your key
ut of the ignition lock.
51 . .
ProCarManuals.com

Trip Odometer
The trip odometer can tell you how far
your vehicle has been driven since you
last set the trip odometer to zero.
To set the trip odometer to zero, press the
knob.
Tachometer
The tachometer displays the engine speed in thousands of revolutions per minute
(rpm).
I NOTICE:
I
Do not operate the engine with the
tachometer in the red area, or engine
damage may occur.
Warning Lights, Gages
and Indicators
This section describes the warning lights
and gages that may be on your vehicle.
The pictures will help you locate them.
Warning lights and gages can signal that
something is wrong before
it becomes
serious enough to cause
an expensive
repair or replacement. Paying attention to
your warning lights and gages could also
save you or others from injury.
Warning lights go on when there may be
or is a problem with one of your vehicle’s
functions.
As you will see in the details
on the next few pages, some warning
lights come on briefly when you turn the
ignition key just to let you know they’re
working. If you are familiar with this
section, you should not be alarmed when
this happens.
Gages can indicate when there may be or
is a problem with one of your vehicle’s
functions. Often gages and warning lights
work together to let you know when
there’s a problem with your vehcle. When
one of the warning lights comes on
and stays on when you are driving, or
when one
of the gages shows there may
be a problem, check the section that tells
you what to do about it. Please follow the
manual’s advice. Waiting to do repairs
can be costly
- and even dangerous. So
please get to know your warning lights
and gages. They’re a big help.
89. .
ProCarManuals.com

Setting the Clock
The clock may be set with the ignition
on or off.
1. Press and hold “HR” until the correct
hour appears.
correct minute appears.
2. Press and hold “MIN” until the
NOTE: There will be
a two second delay
before the clock goes into the time-set
mode.
I
AM/FM Stereo with Cassette
Tape Player
To Play the Radio
Push “POWER” to turn the system on
or off.
Volume
Turn the “VOLUME” knob to adjust
the sound.
AM-FM
Press “AMEM” to get AM, FM1 or
FM2. The lighted display shows your
selection.
%ne
Press “TUNE” to release the knob.
Turn the knob
to choose radio stations.
Push “TUNE’ back
in to store it when
not tuning.
Recall
Press “RECALL” to recall the station
being played or the clock display.
You
can also press “RECALL” to display
the time when
the ignition is off.
Seek
Press “SEEK or A ” and the radio
will tune to
the next lower or higher
station and stay there.
109 ...
ProCarManuals.com

Comfort Controls and Audio Systems
Pushbuttons
The six pushbuttons let you return to
your favorite stations. You can preset
up to 18 stations
(6 AM, 6 FMl and
6 FM2).
1. Press “AM/FM’ to choose AM,
2. Tune in the station.
FM1 or
FM2.
3. Press and hold one of the six
pushbuttons until the display shows
“SET.” Whenever you press that
button, the preset station will
return.
Repeat these steps for each pushbutton.
Steering Wheel Controls
Your vehicle may be equipped with
steering wheel controls for this audio
system. With steering wheel controls,
you can use the buttons
on your
steering wheel to:
Turn the audio system on or off.
Adjust the volume.
Choose AM, FM1 or FM2.
Use the seek and recall functions.
Choose one of the preset stations
on your pushbuttons.
Setting the Tone
Bass:
Slide the “BASS” lever to the
5ght to hear more bass.
I’reble: Slide the “TREBLE’ lever to
:he right to hear more treble.
[f a station is weak and noisy, slide
‘TREBLE’ to the left to reduce the
noise.
Adjusting the Speakers
Balance:
Press “BAL” to release the
knob. Turn the knob to move the sound
between the right and left speakers.
Push “BAL” back in to store
it when
not adjusting.
Fade: Press “FADE” to release the
knob. Turn the knob to move the sound
between the front and rear speakers.
Push “FADE’ back in to store it when
not adjusting.
To Play a Cassette Tape
Your tape player is built to work best
with tapes that are
30 to 45 minutes
long on each side. Tapes longer than
that are
so thin they may not work well
in this player. A cassette symbol will
appear in the upper left corner of the
display whenever a tape is inserted.
The longer side with the tape visible
goes in first. If you hear nothing or
hear just a garbled sound, it may not be
in squarely. Press “EJECT” to remove
the tape and start over.
Once the tape is playing, use “VOLUME,” “FADE,” “TREBLE’
and “BASS” just as you do for the
radio. The arrows show which side of
the tape is playing.
Forward
Press “FWD” to rapidly advance to
another part of the tape. Press “PROG”
or “FWD” again to stop it. The radio will play during this operation.
. . .I10
ProCarManuals.com

Reverse
Press “REV” to rapidly rewind the tape.
Press “PROG’ or “REV” again to stop it.
The radio will play during this operation.
To Play the Next Selection
Press “NEXT” or “SEEK A’’ to hear the
next selection (instead of waiting until the
current selection is finished.)
For “NEXT” to work properly, your tape
must have at least three seconds of silence
between each selection.
The radio will not play during this
operation.
To Replay the Current Selection
Press “PREV” or “SEEK V” to play a
selection again.
For “PREV” to work properly, your tape
must have at least three seconds of silence
between each selection.
The radio will not play during this
operation.
Program
Press “PROG’ to switch from one side of
the tape to the other or to stop the tape
from searching.
Noise Reduction
Press 00 to reduce tape noise. This
symbol will appear in the display.
To Stop the Tape Player
Turn the power off or turn the ignition
key off. The cassette stays in
the
player and will resume playing at the
point where it stopped.
cassette and switch to the radio. Press
“TAPE-PLAY’’ to restart
the cassette
at
the point where it stopped.
e Press “EJECT” to remove the cassette
or stop the cassette and switch to
radio. “EJECT” will work with the
ignition or radio off. Press “EJECT”
to load a cassette when the radio is
off.
0 Press “AMEM” to stop playing the
NOTE: This radio has a “broken tape”
feature that will eject broken or misfed
tapes. Because of this feature, CD:
changers that plug into
the tape deck
will not work in this system.
Theft-Deterrent System
Your audio system is equipped with the
“THEFTLOCK’ theft-deterrent system.
See “Theft-Deterrent System” at the end
of this section.
111 . . .
ProCarManuals.com

Comfort Controls and Audio Systems
AM/FM Stereo with Cassette
Tape Player and Graphic
Equalizer
To Play the Radio
Push “POWER” to turn the system on or
off.
Volume
Turn the “VOLUME’ knob to adjust the
sound.
AM-FM
Press “AMEM’ to get AM, FM1 or FM2.
The lighted display shows your selection.
Tune
Press “TUNE’ to release the knob. Turn
the knob to choose radio stations. Push
“TUNE” back in to store it when not
tuning.
Recall
Press “RECALL” to recall the station
being played
of- the clock display. You can
also press “RECALL,” to display the time
when the ignition is
off.
Seek
Press “SEEK A ” or “SEEK ” to go
to the next lower or higher station and
stay there.
Pushbuttons
The six pushbuttons let you return to
your favorite stations.
To set the
pushbuttons for up to
18 stations
(6 AM, 6 FMl and 6 FM2).
1. Press “AMEM’ to choose AM,
2. Tune in the station.
3. Press and hold one of the six
FM1
or FM2.
pushbuttons until the display
shows
“SET.” Whenever you press that
button, the preset station will return.
. . .112
ProCarManuals.com

Steering Wheel Controls
Your vehicle may be equipped with
steering wheel controls for this audio
system. With steering wheel controls, you
can use the buttons
on your steering
wheel to:
0 Turn the audio system on or off.
Adjust the volume.
Choose AM, FM1 or FM2.
Use the seek and recall functions.
Choose one of the preset stations on
your pushbuttons.
Setting the Tone
Use the levers to set the bass, midrange
and treble until you get the sound you
want. The
“40,” “100,” “250” and
“625” levers adjust the bass.
“1.6K’ is
midrange, and “4K’ and
“l2K’ control
the treble. We suggest setting the “1.6K’
lever in the middle position and then
moving the other levers up or down until
you get the amount of bass and treble you
like.
Adjusting the Speakers
Balance:
Press “BAL” to release the
knob. Turn the knob to move the sound
between the right and left speakers. Push
“BAL” back in to store it when not
adjusting.
Fade: Press “FADE” to release the knob.
Turn the knob to move the sound between
the front and rear speakers. Push “FADE”
back in to store it
when not adjusting.
To Play a Cassette Tape
Your tape player is built to work best with
tapes that are
30 to 45 minutes long on
each side. Tapes longer than that are
so
thin they may not work well in this player.
A cassette symbol will appear in the
upper left corner of the display whenever
a tape is inserted.
The longer side with the tape visible goes
in first. If you hear nothing or hear just a
garbled sound, it may not be in squarely.
Press “EJECT.” to remove the tape and
start over.
Once the tape is playing, use
“VOLUME,” “BAL” and “FADE” just as
you do for the radio. The arrows show
which side
of the tape is playing.
Forward
Press “FWD” to rapidly advance to
another part of the tape. Press “PROG’ or
“FWD’ again to stop it. The radio will
play during this operation.
Reverse
Press “REV” to rapidly rewind the tape.
Press “PROG’ or
“REV” again to stop it.
The radio will play during this operation.
To Play the Next Selection
Press “NEXT” or “SEEK A” to hear the
next selection (instead
of waiting until the
current selection is finished.)
For
“NEXT” to work properly, your tape
must have at least three seconds
of silence
between each selection.
The radio will not play during this
operation.
To Replay the Current Selection
Press “PREV” or “SEEK v” to play a
selection again.
113 ...
ProCarManuals.com

Comfort Controls and Audio Systems
For “PREV” to work properly, your tape
must have at least three seconds of silence
between each selection.
The radio will not play during this
operation.
Program
Press “PROG” to switch from one side of
the tape to the other or to stop the tape
from searching.
Noise Reduction
Press 00 to reduce tape noise. This
symbol will appear in the display.
To Stop the Tape Player
0 Turn the power off or turn the ignition
key
off. The cassette stays in the
player and will resume playing at the
point where it stopped.
Press “AM/FM’ to stop playing the
cassette and switch to the radio. Press
“TAPE-PLAY” to restart the cassette
at
the point where it stopped.
Press “EJECT” to remove the cassette
or stop the cassette and switch to
radio. “EJECT” will work with the
ignition or radio
off. Press “EJECT”
to load a cassette when the radio
is
Off.
NOTE: This radio has a “broken tape”
feature that will eject broken or misfed
tapes. Because of this feature, CD
changers that plug into
the tape deck
will not work
in this system.
Theft-Deterrent System
Your audio system is equipped with the
“THEFTLOCK” theft-deterrent system.
See “Theft-Deterrent System” at the end
of this section.
. . .I14
ProCarManuals.com

AM/FM Stereo with Compact
Disc
Player
To Play the Radio
Push “POWER’ to turn the system on or
Off.
Volume
Turn the “VOLUME’ knob to adjust the
sound.
AM-FM
Press “AM/FM” to get AM, FMl or FM2.
The lighted display shows your selection.
lime
Press “TUNE” to release the knob. Turn
the knob to choose radio stations. Push
“TUNE” back in to store it when not
tuning.
Recall
Press “RECALL” to recall the station
being played or the clock display.
You can
also press “RECALL” to display the time
when the ignition is
off.
Seek
Press “SEEK A ” or “SEEK ” to go to
the next lower or higher station
and stay
there.
Pushbuttons
The six pushbuttons let you return to your
favorite stations. To set the pushbuttons
for
up to 18 stations (6 AM, 6 FM 1 and
6 FM2):
1. Press “A”” to choose AM, FMl
2. Tune in the station.
3. Press and hold one of the six
or FM2.
pushbuttons until the display shows
“SET.” Whenever you press that
button, the preset station will return.
115..
ProCarManuals.com

Comfort Controls and Audio Systems
Steering Wheel Controls
Your vehicle may be equipped with
steering wheel controls for this audio
system. With steering wheel controls, you
can use the buttons on your steering
wheel to:
Turn the audio system on or off.
Adjust the volume.
0 Choose AM, FM1 or FM2.
Use the seek and recall functions.
Choose one of the preset stations on
your pushbuttons.
Setting the Tone
Bass:
Slide the “BASS” lever to the right
to hear more bass.
Treble: Slide the “TREBLE” lever to the
right to hear more treble.
If a station is weak and noisy, slide
“TREBLE’ to
the left to reduce the noise.
Adjusting the Speakers
Balance:
Press “BAL” to release the
knob.
Turn the knob to move the sound
between the right and left speakers. Push
“BAL” back
in to store it when not
adjusting.
Fade: Press “FADE” to release the knob.
Turn
the knob to move the sound between
the front and rear speakers. Push “FADE’
back in to store it when not adjusting.
To Play a Compact Disc
Before you begin, please note: don’t use
the mini-discs that are called “singles.”
They won’t eject. Use full-size compact
discs.
With
the audio system on, insert a disc
into the slot with the label side up. “CD’
will appear on the display and track 1 will
begin to play.
If the disc comes back out and “ERR’
appears on the display, it could be that:
* The disc is upside down.
It is dirty, scratched, or wet.
0 There’s too much moisture in the air.
You are driving on a very rough road.
The temperature is too hot or too cold.
Recall
Press “RECALL” to see what track is
playing. Press it again within five seconds
to see how long it has been playing.
The track number also appears when the
disc is inserted.
To Play the Next Selection
Press “NEXT” or “SEEK A” to hear the
next track now (instead of waiting until
the present track is finished).
If you press and hold this button or press
it more than once, the disc
will advance
further.
To Replay the Current Selection
Press “PREV” or “SEEK v” to hear a
track again.
If you press and hold this button, or press
it more than once,
the disc will return to
previous tracks.
. . .I16
ProCarManuals.com