fuel PONTIAC FIREBIRD 1997 User Guide

If the Light Is On Steady Have you recently changed brands of fuel?
You may be able to correct the emission system
malfunction by considering the following:
Did you recently put fuel into your vehicle?
If
so, reinstall the fuel cap, making sure to fully install
the cap, The diagnostic system can determine if the fuel
cap has been left
off or improperly installed. A loose or
missing fuel cap will allow fuel
to evaporate into the
atmosphere.
A few driving trips with the cap properly
installed should turn the light off.
Did you just drive through
a deep puddle of water?
If so, your electrical system may be wet. The condition
will usually be corrected when the electrical system
dries out. A few driving trips should turn the light
off,
Are you low on fuel?
As your engine starts to run
out of fuel, your engine may
not run as efficiently
as designed since small amounts of
air are sucked into the fuel line causing a misfire. The
system can detect
this. Adding fuel should correct this
condition. Make sure to install
the fuel cap properly. It
will take a few driving trips to turn the light off. If
so, be sure to fuel your
vehicle with quality fuel (see
“Fuel” in the Index). Poor fuel quality will cause your
engine
not to run as efficiently as designed. You may
notice this as stalling after start-up, stalling when you
put the vehicle into gear, misfiring, hesitation on
acceleration or stumbling on acceleration. (These
conditions may
go away once the engine is warmed up.)
This will be detected by the system and cause the light
to turn on.
If you experience one or more
of these conditions,
change the fuel brand
you use. It will require at least one
full tank of the proper fuel to turn the light off.
If none
of the above steps have made the light turn off,
have your dealer or qualified service center check the
vehicle. Your dealer has the proper test equipment
and
diagnostic tools to fix any mechanical or electrical
problems that
may have developed.
2-86

Check Gages Light When the gage pointer first indicates EMPTY (E) you
need to get more right away.
CHECK
GAGES
Fuel Gage
I
This warning light will
come on briefly when
YOU
are starting the engine. If
the light comes on and
stays on while you are
driving, check your gages
to see if they are in the
warning areas.
Your fuel gage shows about
how much fuel is in
your
tank. The gage works only
when the ignition switch is
in the RUN position. Here are four concerns some owners have had
about the
fuel gage. All these situations are normal and do not
indicate that anything
is wrong with the fuel gage.
0
0
0
0
At the gas station, the gas pump shuts off before the
gage reads FULL
(F).
It takes more (or less) gas to fill up than the gage
reads. For example, the gage reads
1/2 full, but it
took more (or less) than half
of the tank's capacity to
fill it.
The gage moves
a little when you turn, stop or
speed up.
When you turn the engine off, the gage doesn't go
back to
EMPTY (E).

Air Conditioning (If Equipped)
I
The air conditioning system uses the same controls as
the heating system, except that the air control knob has
two extra settings, described below.
MAX: Provides maximum cooling or quick cool-down
on very hot days. This setting recirculates most of the air
inside your vehicle.
If it is used for long periods of time,
the air may become dry. This setting directs air through
the upper air vents,
A/C: Use for normal cooling on hot days. This setting
cools outside
air and c‘kts it through the upper air vents.
The i-111- conditioner cumpressor operates in MAX, AIC,
BI-LEVEL, BLEND and DEFROST when the outside
temperature is above freezing. When the
air conditioner
is on,
you may sometimes notice slight changes in
your vehicle’s engine speed and power. This is normal
because the system is designed to cycle the compressor
on and
off to keep the desired cooling and help
fuel economy.
Cooling
The air conditioner works best if you keep your
windows closed. On very
hot days, open the windows
just long enough for the hot air to escape.
1. Turn the air control knob to A/C for normal cooling.
For faster cooling, move the
knob to MAX.
2. Turn the temperature control knob to a
comfortable setting.
3. Move the fan control knob to the desired speed.

Once you are moving on the freeway, make certain you
allow a reasonable following distance. Expect to move
slightly slower at night.
When you want to leave
the freeway, move to the proper
lane well in advance.
If you miss your exit, do not,
under any circumstances, stop
and back up. Drive on to
the next exit.
The exit ramp can
be curved, sometimes quite sharply.
The exit speed is usually posted.
Reduce
your speed according to your speedometer, not
to your sense of motion. After driving for any distance
at higher speeds, you may tend to think you are going
slower
than you actually are,
Before Leaving on a Long Trip
Make sure you’re ready. Try to be well rested. If you
must start when you’re not fresh
-- such as after a day’s
work
-- don’t plan to make too many miles that first part
of the journey. Wear comfortable clothing and shoes you
can easily drive in,
Is your vehicle ready for a long trip? If you keep it
serviced and maintained, it’s ready
to go. If it needs
service, have it done before starting out. Of course,
you’ll find experienced and able service experts in
Pontiac dealerships all across North America.
They’ll be
ready and willing to help if you need it.
Here are
some things you can check before a trip:
0
a
a
a
a
0
Windshield Washer Fluid: Is the reservoir full? Are
all windows clean inside and outside?
Wiper Blades: Are they in good shape?
Fuel, Engine Oil, Other Fluids: Have you checked
all levels?
Lamps: Are they all worlung? Are the lenses clean?
Tires: Th’ey are vitally important to a safe,
trouble-free trip.
Is the tread good enough for
long-distance driving? Are the tires all inflated to the
recomended pressure?
Weather Fureecasts: What’s the weather outlook
along your route? Should you delay
your trip a short
time to avoid a major storm system?
Maps: Do you have up-to-date maps?
4-22

A CAUTION: ..
Snow can trap exhaust gases under your vehicle.
This can cause deadly CO (carbon monoxide) gas
to get inside.
CO could overcome you and kill
you. You can’t see
it or smell it, so you might not
know it is in your vehicle. Clear away snow from
around the base of your vehicle, especially any
that
is blocking your exhaust pipe. And check
around again from time to time to be sure snow
doesn’t collect there.
Open
a window just a little on the side of the
vehicle
that’s away from the wind. This will help
keep
CO out.
Run your engine only as long as you must. This saves
fuel. When you run the engine, make
it go a little faster
than just idle. That
is, push the accelerator slightly. This
uses less fuel for the heat that you get and it keeps the
battery charged. You will need a well-charged battery to
restart the vehicle, and possibly for signaling later
on
with your headlamps. Let the heater run for awhile.
Then, shut the engine
off and close the window almost
all the way to preserve the heat. Start the engine again
and repeat this only when you feel really uncomfortable
from the cold. But do
it as little as possible. Preserve the
fuel as long as you can. To help keep warm, you can get
out of the vehicle and do some fairly vigorous exercises
every half hour or so until help comes.
4-29

Loading Your Vehicle
cm OCCUPANTS VEHICLE CAP. WT.
TIRE-LOADING INFORMATION -.
FRT. CTR. RR. TOTAL LBS. KG
MAX. LOADING & GVWR SAME AS VEHICLE
CAPACITY WEIGHT XXX COLD TIRE
TIRE SIZE SPEED PRESSURE
RTG PSI/KPa
FRT.
RR.
SPA.
IF TIRES ARE HOT, ADD 4PS1/28KPa
SEE OWNER'S MANUAL FOR ADDITIONAL
I'NFORMATION
Two labels on your vehicle show how much weight it
may properly
carry. The Tire-Loading Information l'abel
found on the driver's
door tells you the proper size,
speed rating and recommended inflation pressures for
the tires on your vehicle. It also gives you important
information about the number of people that can be in
your vehicle and the total weight that you can carry,
This weight is called the vehicle capacity weight and
includes the weight of all occupants, cargo, and all
nonfactory-installed options.
MFB BY GENERAL MOTORS CORP
DATE GVWW GAWR FRT GAWR RR
THIS VEHICLE CONFORMS TO ALL APPLI-
CABLE U.S. FE:DERAL MOTOR VEHICLE
SAFETY,
BUMPER, AND THEFT PREVENTION
STANDARDS IN EFFECT ON THE DATE OF
MANUFACTURE SHOWN ABOVE.
The other label is the Certification label, found on the
rear edge of the driver's door. It tells you the gross
weight capacity of your vehicle,
called GVWR (Gross
Vehicle Weight Rating). The GVWR includes the weight
of the vehicle, all occupants, fuel and cargo. Never
exceed
the GVWR for your vehicle, or the Gross Axle
Weight Rating
(GAWR) for either the front or rear axle.
And, if you do have a heavy load, you should spread
it out. Don't ca more than 100 lbs. (45 kg) in your
rear area.

Towing a Trailer
If you don’t use the correct equipment and drive
properly, you can lose control when you pull a
trailer. For example, if the trailer
is too heavy, the
brakes may not work well
-- or even at all. You
and your passengers could be seriously injured.
Pull
a trailer only if you have followed all the
steps in this section.
Ask your Pontiac dealer for
advice and information about towing
a trailer
with your vehicle.
NOTICE:
Pulling a trailer improperly can damage your
vehicle and result in costly repairs not covered by
your warranty.
To pull a trailer correctly, follow
the advice in this part, and see your Pontiac
dealer
for important information about towing a
trailer with your vehicle.
Your vehicle can tow a trailer if it is equipped with the
3800 and 5.7L engines and proper trailer towing
equipment.
To identify what the vehicle trailering capacity
is for your vehicle,
you should read the inforrnation in
“Weight of the Trailer” that appears later in
this section.
But trailering is different than just driving your vehicle by
itself. Trailering means changes in handling, durability and
fuel economy. Successful, safe trailering
takes correct
equipment, and it has to be used properly.
That’s the reason for this part. In it are many
time-tested, important trailering tips and safety rules.
Many of these are important for your safety and
that of
your passengers. So please read this section carefully
before
you pull a trailer.
4-32

Section 6 Service and Appearance Care
Here you will find information about the care of your Pontiac. This section begins with service and fuel information,
and then it shows how to check imDortant fluid and lubricant levels. There is also technical information about your I
vehicle, and a part devoted to its appearance care.
6-2 Service
6-3 Fuel
6-5 Fuels in Foreign Countries
6-6 Filling Your Tank
6- 8 Checking Things Under the Hood
6- 12 Engine Oil
6-18 Air Cleaner
6-22 Automatic Transmission Fluid 6-27 Manual Transmission Fluid
6-29 Engine Coolant
6-3
3 Power Steering Fluid
6-35 Windshield Washer Fluid
6-36 Brakes
6-40 Battery
6-4
1 Bulb Replacement 6-49
6-58
6-5
8
6-6 1
6-63
6- 64
4-65
6-66
6- 67
6-68
6-68
6-68
6-73
6-73
Tires
Appearance Care Cleaning the Inside
of Your Pontiac
Care
of Safety Belts
Cleaning the Outside
of Your Pontiac
Aluminum
or Chrome Wheels
Tires
Underbody Maintenance
Appearance Care Materials Chart
Vehicle Identification Number (VIN)
Service Parts Identification Label
Electrical System
Replacement
Bulbs
Capacities and Specifications
6-1

You can be injured and your vehicle could be
damaged if you try to
do service work on a
vehicle without knowing enough about it.
Be sure you have sufficient knowledge,
experience, the proper replacement parts
and tools before you attempt any vehicle
maintenance task.
Be sure to use the proper nuts, bolts and
other fasteners. “English” and (‘metric”
fasteners can be easily confused.
If you use
the wrong fasteners, parts can later break
or fall off. You could be hurt.
Adding Equipment to the Outside of
Your Vehicle
Things you might add to the outside of your vehicle can
affect the airflow around it. This may cause wind noise
and affect windshield washer performance. Check with
your Pontiac dealer before adding equipment
to the
outside
of your vehicle.
Fuel
The 8th digit of your vehicle identification number
(VIN) shows the code letter for your engine. You will
find the
VIN at the. top left of your instrument panel.
(See “Vehicle Identification Number” in the Index.)
If you have the 3800 engine (VIN Code K), use regular
unleaded gasoline rated at
87 octane or higher.
If you have the 5.7L engine (VIN Code I?), use premium
unleaded gasoline rated at
91 octane or higher for best
performance. You may use middle grade or regular
unleaded gasolines, but your vehicle may not accelerate
as well.

At a minimum, the gasoline you use should meet
specifications
ASTM D4814 in the United States and
CGSB 3.5-M93 in Canada. Improved gasoline
specifications have been developed by the American
Automobile Manufacturers Association
(AAMA) for
better vehicle performance and engine protection.
Gasolines meeting the AAMA specification could
provide improved driveability and emission control
system protection compared to other gasolines,
Be sure the posted octane for premium is at least
91 (at least 89 for middle grade and 87 for regular).
If the octane is less than
87, you may get a heavy
knocking noise when
you drive. If it’s bad enough,
it can damage your engine.
If you’re using fuel rated at the recommended octane
or higher and you still hear heavy knocking, your
engine needs service.
But dm9t worry if you hear a little
pinging noise when you’re accelerating
or driving up a
hill. That’s normal, and you don’t have
to buy a higher
octane fuel
to get rid of pinging. It’s the heavy, constant
knock that means you have
a problem. If
your vehicle is certified
to meet California Emission
Standards (indicated on the underhood tune-up label), it
is designed to operate on fuels that meet California
specifications. If such fuels are
not available in states
adopting California emissions standards, your vehicle
will operate satisfactorily
on fuels meeting federal
specifications, b’ut emission control system performance
may be affected. The malfunction indicator lamp
on
your instrument panel may turn on and/or your vehicle
may fail
a smog-check test. If this occurs, return to your
authorized Pontiac dealer for diagnosis to determine
the
cause of failure. In the event it is determined that the
cause of the condition is the type of fuels used, repairs
may not be covered by your warranty.
Some gasolines that
are not reformulated for low
emissions contain
an sctane-enhancing additive called
methylcyclopentadienyl manganese tricarbonyl (MMT);
ask your service station operator whether or not his fuel
contains
MMT. General Motors does not recommend the
use of such gasolines. If fuels containing MMT are used,
spark plug life may be reduced and your emission
control system performance may
be affected. The
malfunction indicator lamp on your instrument panel
may turn
on. If this occurs, return to your authorized
Pontiac dealer for service.
6-4