ECO mode PONTIAC FIREBIRD 1997 Owners Manual

AlarmRanic Mode Operation
The driver’s door will unlock automatically when
UNLOCK is pressed.
If UNLOCK is pressed again
within five seconds, the passenger door will also unlock.
All doors will lock when
LOCK is pressed.
The hatch will unlock when the button with the trunk
symbol is pressed twice within five seconds, as long as
the ignition is turned to the
OFF position. If the ignition
is on, the trunk symbol button will only work if the
transmission is in
PARK (P) for an automatic
transmission, or if the parking brake is set on a manual
transmission.
The system will turn on the interior lamps for about
40
seconds (or until the ignition switch is turned to the
RUN position), when you unlock the doors or hatch.
The interior lamps will go
off when you lock the doors.
Operating the key chain transmitter may interact with
the Vehicle and Content Theft-Deterrent System
(if you
have this option). See “Vehicle and Content
Theft-Deterrent System” in the Index.
If your vehicle is equipped with the Vehicle and Content
Theft-Deterrent System, you will have a fourth button
on your key chain transmitter. This button
is the panic
button. If you are involved in a panic situation, press
this button and your vehicle’s horn will sound and the
parking lamps will flash. This will draw needed
attention to you and your vehicle. To turn this feature
off, either push the panic button again or turn the
ignition to on. Note: This feature will not work if your
ignition is on
or if the key fob is 30 feet (9 m) or more
away from your vehicle.
Transmitter Range
The range of your Remote Keyless Entry system should
be about 3 feet (1 m) up to 30 feet (9 m). At times you
may notice a decrease in the range. This is normal for
any Remote Keyless Entry system. If the transmitter
does not work, or you have to stand closer to your
vehicle than normal for the transmitter to work:
0 You may have to replace the battery in
your transmitter. See
the instructions for
battery replacement.
You may be too far from your vehicle. Check your
distance,
You may have to stand closer to your
vehicle in rain or snow.
2-7

Arming the System
The alarm system can be
armed to detect break-ins
by locking your vehicle
using the key chain
transmitter or by locking
the
doors with the power door
lock switch.
Passive arming is also available,
if you would like the
system to
am all by itself after the doors have been
closed for a short time. When the system
is armed, a red
light will flash briefly once every two seconds. (Note:
If
you return to your vehicle and the red light is flashing
two
brief flashes every two seconds, the system is armed
and the shock sensor had triggered a two minute alarm.
If the red light is flashing three times every two seconds,
the system
is armed and there was an intrusion that
sounded the alarm).
Horn chirps and parking lamp
flashes can be
set to your choice.
Remote Keyless Entry Transmitter Locking
If all the doors are closed, locking the vehicle with the
transmitter will immediately arm the system. The horn
will chirp twice and the
parking lamps will flash,
confirming that the system
is armed. If any door is open
when the transmitter
LOCK button is pressed, the
system goes into an armed wait mode, waiting for the
doors
to close. Once they are closed, the system will
arm, chirp the horns twice and flash the parking lamps.
If the hatch
is open or ajar at the time the system is
arming, the
horn will only chirp once.
Power Door Lock Switch Locking
If any door is open when the power door lock switch is
pressed, the system goes into an armed wait mode,
waiting for the doors to close. Once they are closed, the
system will arm and flash the parking lamps.
If all of the
doors are closed when the lock switch is pressed, the
system assumes
you are inside the vehicle, so it will not
arm. Note: Locking the doors
by using the manual door
locks will
not arm the system.
2-14

To program features, your vehicle must be in the
programming mode. Follow these steps:
1.
2.
3.
4.
5.
Put your key in the ignition.
Turn the ignition to the
RUN pos’ition to disarm the
Vehicle and Content Theft-Deterrent System.
Turn the ignition
to the OFF position.
Remove the RADIO
fuse. This fuse is in the main
fuse block, located on the left side of your
instrument panel. See “Fuses and Circuit Breakers”
in the Index.
Put the ignition in the
ACC position:
You should hear
a chime to verify that the system is
in programming mode.
If the chime sounds once,
you will be able
to program Exit Lighting, Delayed
Illumination, Last Door Closed Locking and Lockout
Prevention only.
If the chime sounds twice and your
vehicle is equipped with the Vehicle and Content
Theft-Deterrent System,
you will also be able to set
Remote
Lock Control Verification, Arming Method,
Arming Verification, Driver’s Door Delay and Shock
Sensor Enable.
Exit Lighting and Delayed Illumination
Exit Lighting: Your interior lights will come on for
up to
25 seconds when the key is removed from the
ignition switch.
Delayed Illumination: Your interior lights will stay
on
for up to 25 seconds when entering your vehicle and up
to five seconds when leaving your vehicle.
Your vehicle comes with both features enabled (Mode
4).
To change the factory setting, do the following:
1. Turn the courtesy lamps on by turning the instrument
panel brightness control knob all the way up.
2. Count the number of chimes you hear. The number of
chimes tells you which mode your vehicle is set for.
3. Turn the courtesy lamp switch to off.
4. Turn the courtesy lamp switch from on to off until
you hear the number of chimes that correspond to the
mode selection
you want.
Mode 1: Both Off
Mode 2: Delayed Illumination Only
Mode 3: Exit Lighting Only
Mode 4: Both On
2-18

Last Door Closed Locking and
Lockout Prevention
Your vehicle comes with this feature set in Mode 2. This
means that your power door locks will not lock when
the keys are in the ignition and a door is open. To
change the factory setting, do the following:
1. Press the LOCK switch on the door.
2. Count the number of chimes you hear. The number of
chimes tells you which mode your vehicle is set for.
3. Press the LOCK switch on the door until you hear
the number
of chimes that correspond to the mode
selection you want.
Mode 1: Both O€€ (Doors will 1ocWunlock when you
press the power door lock switch).
Mode 2: Lockout Prevention Only (If you leave your
keys in the ignition and get out the driver’s door, you
won’t be able
to lock the doors with the power door
lock switch).
Mode 3: Last Door Closed Locking Only (If the power
door lock switch is used to lock the vehicle while any
door is open, you will hear three chimes. The doors will
not lock until after all doors are closed).
Mode 4: Both On (This combines Mode 2 and 3).
Remote Keyless Entry Lock Verification
Your vehicle comes with this feature set in Mode 5. This
means that when you
use the key chain transmitter to
lockhnlock your vehicle, your parking lamps will flash
briefly upon the first push
on LOCK. Your horn will
sound briefly, your parking lamps will flash briefly upon
the second push on LOCK and your parking lamps will
flash briefly upon any push on UNLOCK.
To change the
factory setting, do the following:
1. Press the UNLOCK switch on the Remote Keyless
2. Count the number of chimes you hear. The number
of chimes tells you which mode your vehicle is
set for.
Entry transmitter.
3. Press the UNLOCK switch on the Remote Keyless
Entry transmitter until you hear the number
of
chimes that correspond to the mode selection
you want.
2-19

Mode 1: All Off (The headlamps will not flash and the
horn will not sound
to provide you feedback that a
lock/ud~& command has been received by the Remote
Lock Control transmitter).
Mode 2: Horn and LampdLamps (Your horn will sound
briefly and your parking lamps will flash when you
press
LOCK on the key chain transmitter. Only your
parking lamps will flash when you press
UNLOCK).
Mode 3: Horn and Lamps (Your horn will sound briefly
and your parking lamps will flash every time you push
LOCK and
UNLOCK).
Mode 4: Lamps (Your parking lamps will flash every
time
you push LOCK and UNLOCK),
Mode 5: Lamps/Horn and Lamps/Lamps (Your
lamps will flash
upon the first push on LOCK, your
lamps will flask and
your horn will sound upon the
second push on
LOCK and your lamps will flash upon
any push on
UNLOCK).
Theft-Detlerrent Arming Method
Your vehicle comes with this feature set in Mode 3. This
means that both your key chain transmitter and the
power door lock switch will actively arm the system.
To
change the factory setting, do the following:
1. Press the UNLOCK switch on the door.
2. Count the number of chimes you hear. The number of
chimes tells you which mode your vehicle is set for,
3. Press the UNLOCK switch on the door until you
hear the number
of chimes that correspond to the
mode selection
you want.
Mode I: Alarm System Off (The system will not arm).
Mode 2: Key Chain Transmitter Lock (When you lock
your doors using the Key Chain Transmitter, the system
will arm itself).
Mode 3: Key Chain TransmittedPower Door Lock
Switch
(If you use either the Key Chain Transmitter or
the power door
lock switch to lock the doors, the system
will arm itself).
Mode 4: Passive arming and Remote Lock Control
Transmitter/Power Door Lock Switch Arming
(The
system will arm itself after all doors are closed plus
arming per;mg&
3).
2-20

Driver’s Door Alarm Delay and Shock
Sensor Enable
Your vehicle comes with this feature set in Mode 4.
This means that if you open the driver’s door using
your key, the alarm will not sound
for eight seconds.
Also the shock sensor, able
to detect sharp blows to
your vehicle, is active.
To change the factory setting, do
the following:
1. Turn the parking lamps
on and off,
2. Count the number of chimes you hear. The number
of chimes tells you which mode your vehicle is
set for.
3. Turn the parking lamps on and off until you hear the
number of chimes that correspond to the mode
selection you want.
Mode 1: Zero Delay and Shock Sensor Disabled (The
alarm will sound immediately
if the driver’s door is
opened with your
key and the shock sensor will not be
available to measure sharp blows to your vehicle).
Mode 2: Eight Second Delay and Shock Sensor
Disabled (The alarm will sound eight seconds after the
driver’s door is opened with your key and the shock
sensor will not be available to measure sharp blows to
your vehicle),
Mode 3: Zero Relay and Shock Sensor Enabled (The
alum will sound immediately after the driver’s door is
opened with your key and the
shock sensor will be
available
to measure sharp blows to your vehicle).
Mode 4: Eight Second Delay and Shock Sensor Enabled
(The alarm will
sound eight seconds after the driver’s
door is
opened with your key and the shock sensor will
be available to measure sharp
blows to your vehicle).
Leaving Programming Mode
When programming is done, turn the ignition switch to
the
OFF position and replace the RADIO fuse.
2-22

This feature is for improved traction only ,when the road
surface is slippery and is not intended for continuous use
or when the vehicle is stuck in sand, mud, ice, snow or
gravel. Always use
NORMAL for normal road
conditions. You may press the 2ND GEAR START
switch again to turn
off this feature. The light on the
switch will
go out. Whenever you start your vehicle, the
transmission is in the NORMAL
mode.
Manual Transmission
5-Speed
1 3 5
2 4 R
This is your shift pattern.
Here’s how to operate
your transmission:
FIRST (1): Press the clutch pedal and shift into
FIRST (1). Then slowly let up on the clutch pedal as
you press the accelerator pedal.
You can shift into FIRST (1) when you’re going less
than
20 mph (32 km/h). If you’ve come to a complete
stop and it’s
hard to shift into FIRST (l), put the shift
lever in NEUTRAL
(N) and let up on the clutch, Press
the clutch pedal back down. Then shift into FIRST
(1).
SECOND (2): Press the clutch pedal to the floor as
you let up on the accelerator pedal and shift into
SECOND
(2). Then, slowly let up on the clutch pedal as
you press the accelerator pedal.
THIRD (3), FOURTH (4), and FIFTH (5): Shift into
THIRD
(3), FOURTH (4) and FIFTH (5) the same way
you
do for SECOND (2). Slowly let up on the clutch
pedal as
you press the accelerator pedal.
To Stop, let up on the accelerator pedal and press the
brake pedal. Just before the vehicle stops, press the
clutch pedal and the brake pedal, and shift to
NEUTRAL
(N),
NEUTRAL (N): Use this position when you start or
idle your engine.
2-32

Ventilation Tips
a Keep the hood and front air inlet free of ice, snow or
any other obstruction (such
as leaves). The heater
and defroster will work far better, reducing the
chance
of fogging the inside of your windows.
When you enter
a vehicle in cold weather, turn the
fan control
knob to the right for a few moments
before driving
off. This helps clear the intake ducts
of snow and moisture, and reduces the chance of
fogging
the inside of your windows.
Keep the air path under the rront sems clear of
objects. This helps air to circulate throughout
your vehicle.
Audio Systems
Your Delco@ audio system has been designed to operate
easily and give years
of listening pleasure. You will get
the most enjoyment out
of it if you acquaint yourself
with it first. Find out what your Delco system can do
and how to operate all its controls,
to be sure you’re
getting the most out o’f the advanced ‘engineering that
went into it.
If you have power door locks, your vehicle has a feature
called Retained Accessory Power
(RAP). With RAP,
you can play your audio system even after the ignition is
off. See “Retained Accessory Power” in the Index.
Setting the Clock for All Systems
Press and hold HR until the correct hour appears. Press
and hold MIN until the correct minute appears. There
will
be a two-second delay before the clock goes into
time-set mode, and the colon on the display will blink
while
in this mode.
3-6

Playing a Compact Disc
PREV
(1): Press this button to go back to the start of
the current track if more than eight seconds have played.
Press PREV again to go to the previous track
on
the disc.
NEXT (2): Press this button to advance to the next track
on the disc.
PROG (3): Press this button to select the next disc in
the magazine.
If a CD cannot be played, its number
will be skipped when selecting discs while using the
PROG button.
RANDOM (4): Press this button to enter the random
play mode.
RDM will appear on the display. While in
this mode, the tracks on the discs will be played in
random order.
If you press PRQG or SEEK while in the
random mode, discs and tracks will be scanned
randomly. Press this button again to turn
off the random
feature and return to normal operation.
REV (5): Press and hold this button to quickly reverse
within
a track. As the CD reverses, elapsed time will be
displayed to help you find the correct passage.
FWD (6): Press and hold this button to quickly advance
within
a track. As the CD advances, elapsed time will be
displayed to help you find the correct passage.
RECALL: Press this button to see what track is
currently playing. Press
RECALL again within five
seconds to see how long the track has been playing.
EL
TM will appear on the display when in elapsed time
mode. When a new track starts to play, the track number
will also appear.
Press RECALL a third time and the
time
of day will be displayed.
SEEK: Press the SEEK down arrow while playing a CD
to go back to the start of the current track if more than
eight seconds have played.
If you press it again, the
changer will
go to previous tracks. Press the SEEK up
arrow and it will go to the next higher track on the disc.
TAPERLAY: Press this button to play a CD if you
have
a magazine loaded in the changer and the radio is
playing.
To return to the radio while a CD is playing,
press
AM-FM. You can also press this button to switch
between
a cassette tape and CD, if both are loaded.
3-18

Replacing Brake System Parts
The braking system on a modern vehicle is complex. Its
many parts have to be of top quality and work well
together if the vehicle is to have really good braking.
Vehicles we design and test have top-quality
GM brake
parts in them, as your Pontiac does when
it is new.
When you replace parts
of your braking system -- for
example, when your brake linings wear down and you
have to have new ones put in
-- be sure you get new
genuine
GM replacement parts. If you don’t, your
brakes may no longer work properly. For example, if
someone puts in brake linings that are wrong for your
vehicle, the balance between your front and rear brakes
can change
-- for the worse. The braking performance
you’ve come
to expect can change in many other ways if
someone puts in the wrong replacement brake parts.
Battery
Every new Pontiac has a Delco Freedom@ battery. You
never have to add water to one of these. When it’s time
for a new battery, we recommend a Delco Freedom
battery. Get
one that has the replacement number shown
on the original battery’s label.
Vehicle Storage
If you’re not going to drive your vehicle for 25 days
or more, take off the black, negative
(-) cable from
the battery. This will help keep your battery from
running down.
Batteries have acid that can burn you and gas
that can explode. You can be badly hurt if you
aren’t careful. See
‘‘Jump Starting” in the Index
for tips on working around a battery without
getting hurt.
I 1
Contact your dealer to learn how to prepare your vehicle
for longer storage periods.
Also, for your audio
system, see “Theft-Deterrent
Feature”
in the Index.
6-40