oil change PONTIAC FIREBIRD 1998 Owners Manual

Have you recently changed brands of fuel?
If so, be sure to fuel your vehicle with quality fuel (see
“Fuel” in the Index). Poor fuel quality will cause your
engine not to run as efficiently as designed. You may
notice this as stalling after start-up, stalling when you
put the vehicle into gear, misfiring, hesitation on
acceleration or stumbling on acceleration. (These
conditions may go away once the engine is warmed up.)
This will be detected by the system and cause the light
to turn on.
If you experience one or more of these conditions,
change the fuel brand you use. It will require at least one
full tank of the proper fuel to turn the light off.
If none of the above steps have made the light turn off,
have your dealer or qualified service center check the
vehicle. Your dealer has the proper test equipment and diagnostic tools to fix any mechanical or electrical
problems that may have developed.
Oil Pressure Gage
\*
0
/
0 120
3800 V6 Engine 5.7L VS Engine
One of these gages may tell you there could be a
problem with
your engine oil pressure.
The engine oil pressure gage shows the engine oil pressure
in psi (pounds per square inch) in the United States, or kpa
(kilopascals)
in Canada, when the engine is running. On
the 5.7L V8 engine, oil pressure should be 20 to 80 psi
(140 to 550 Pa). On the 3800 V6 engine, the oil pressure
should be between 20 and 120 psi (140 to 827 Wa). It
may vary with engine
speed, outside temperature and oil
viscosity, but readings above the red area show the normal
operating range. Readings
in the red area tell you that the
engine is low
on oil, or that you might have some other oil
problem. See “Engine Oil” in the Index.

When to Add Engine Oil What Kind of Engine Oil to Use
If the oil is at or below the ADD line, then you’ll
Oils recommended for your vehicle can be identified
need to add at least one quart of oil. But you must
by looking for the “Starburst” symbol. This symbol
use the right kind. This part explains what kind of oil
indicates that the oil has been certified by the American
to use. For crankcase capacity, see “Capacities and
Petroleum Institute
(API). Do not use any oil which
Specifications” in the Index.
does not carry this Starburst symbol.
NOTICE:
Don’t add too much oil. If your engine has so
much oil that the oil level gets above the
cross-hatched area that
shows the proper
operating range, your engine could be damaged.
Be sure to fill it enough to put the level somewhere in
the proper operating range. Push the dipstick all the
way back in when you’re through.
AAAA
-.v-
If you change your own
oil, be sure you use oil
that
has the Starburst
symbol on the front
of the
oil container. If you have
your oil changed for you,
be sure the oil put into
your engine
is American
Petroleum Institute certified
for gasoline engines.
You should also use the proper viscosity oil for your
vehicle,
as shown in the following chart:
6-14

RECOMMENDED SAE VISCOSITY GRADE EH61NE OILS
HWI BEST FUEL ECONOMY AND COLD STARTIWB, SELECT THE LOWEST
S4€ YISCBSITT 8RllM OIL FOR THE EXPECTED TEMPERANURE RANGE.
HOT
WEATHER
COLD
111 SAE I low-30
PREFERRED mbovs OOF (-16’C)
WEATHER
DO NOT USE SAE 2OW-50 OR AMY OTHER GRADE OIL NOT RECOMMENDED
3800 V6 Engine
As shown in the chart, if you have the 3800 engine,
SAE low-30 is best for your vehicle. However, you
can use
SAE 5W-30 if it’s going to be colder than
60°F (16°C) before your next oil change. When it’s
very cold,
you should use SAE 5W-30. These numbers
on
an oil container show its viscosity, or thickness. Do
not use other viscosity oils, such as SAE 20W-50.
I NOTICE:
Use only engine oil with the American Petroleum
Institute Certiaed For Gasoline Engines
‘‘Starburst” symbol. Failure to use the
recommended oil can result in engine damage not
covered
by your warranty.
GM Goodwrench@ oil meets all the requirements for
your vehicle.
If you are in an area where the temperature falls below
-20°F (-29”C), consider using either an SAE SW-30
synthetic oil or an SAE OW-30 oil. Both will provide
easier cold starting and better protection for
your engine
at extremely low temperatures.
6-16

Engine Oil Additives
Don’t add anything to your oil. Your dealer is ready to
advise if you think something should be added.
When to Change Engine Oil
If any one of these is true for you, use the short tripjcity
maintenance schedule:
0
0
0
0
0
Most trips are less than 5 to 10 miles (8 to 16 km).
This is particularly important when outside
temperatures
are below freezing.
Most trips include extensive idling (such as frequent
driving in stop-and-go traffic).
Most trips are through dusty areas.
You frequently tow a trailer or use
a carrier on top
of your vehicle.
The vehicle is used for delivery service, police,
taxi or other commercial application.
Driving under these conditions causes engine oil to
break down sooner. If any one of these is true for your
vehicle, then you need to change your oil and filter every
3,000 miles (5 000 km) or 3 months -- whichever
occurs first. If
none of them is true, use the long triphighway
maintenance schedule. Change the oil and filter every
7,500 miles (1 2 500 km) or 12 months -- whichever
occurs first. Driving a vehicle with a fully warmed
engine under highway conditions causes engine
oil to
break down slower.
What to Do with Used Oil
Did you know that used engine oil contains certain
elements that may be unhealthy for your skin and could
even cause cancer? Don’t let used
oil stay on your skin
for very long. Clean your skin and nails with soap and
water, or a good hand cleaner. Wash or properly throw
away clothing or rags containing used engine oil. (See
the manufacturer’s warnings about the use and disposal
of oil products.)
Used oil can be a real threat
to the environment. If you
change your own oil, be sure to drain all free-flowing
oil from the filter before disposal. Don’t ever dispose
of oil by putting it in the trash, pouring it on the ground,
into sewers,
or into streams or bodies of water. Instead,
recycle it by taking it to a place that collects used oil. If
you have a problem properly disposing
of your used oil,
ask your dealer, a service station or a local recycling
center for help.
6-17

If you have the 5.7L V8 engine (with the WS6 option),
your air cleaner will be located over the radiator near the
front of the engine.
To remove the filter, remove the screws (located on the
rear edge of the air cleaner), lift the
air cleaner and
remove the filter.
Automatic Transmission Fluid
When to Check and Change
A good time to check your automatic transmission fluid
level is when
the engine oil is changed.
Change both the fluid and filter every
15,000 miles
(25 000 km) if the vehicle is mainly driven under one
or more
of these conditions:
0 In heavy city traffic where the outside temperature
regularly reaches
90°F (32°C) or higher.
In hilly or mountainous terrain.
Uses such as high performance operation.
When doing frequent trailer towing.
0 Uses such as found in taxi, police or delivery service.
If you
do not use your vehicle under any of these
conditions, change the fluid and filter every
50,000 miles (83 000 km).
See “Scheduled Maintenance Services” in the Index.
6-20

3. Check both sides of the dipstick, and read the lower
level.
The fluid level must be in the COLD area for a
cold check or in the
HOT area or cross-hatched area
for a hot check.
4. If the fluid level is in the acceptable range, push the
dipstick back in all the way.
How to Add Fluid
Refer to the Maintenance Schedule to determine what
kind
of transmission fluid to use. See “Recommended
Fluids and Lubricants” in the Index.
Add fluid only after checking the transmission fluid
while it is hot. (A cold check is used only as a
reference.) If the fluid level
is low, add only enough of
the proper fluid to bring the level up to the
HOT area
for a hot check. It doesn’t take much fluid, generally less than one pint
(0.5 L). Don’t ove@ZZ.
I NOTICE:
We recommend you use only fluid labeled
DEXRON@-111, because fluid with that label is
made especially for your automatic transmission.
Damage caused
by fluid other than DEXRON-I11
is not covered by your new vehicle warranty.
After adding fluid, recheck the fluid level as
described under “How to Check.”
When the correct fluid level is obtained, push the
dipstick back in all the
way.
Manual Transmission Fluid
When to Check
A good time to have it checked is when the engine
oil is changed. However, the fluid in your manual
transmission doesn’t require changing.
6-24

A 50/50 mixture of water and DEX-COOL@
coolant will:
0 Give freezing protection down to -34°F (-37°C).
0 Give boiling protection up to 265 “F (1 29°C).
Protect against rust and corrosion.
Help keep the proper engine temperature.
Let the warning lights and gages work as
they should.
NOTICE:
When adding coolant, it is important that you
use only DEX-COOL@ (silicate-free) coolant.
If coolant other than DEX-COOL is added to
the system, premature engine, heater core or
radiator corrosion may result.
In addition, the
engine coolant
will require change sooner -- at
30,000 miles (50 000 km) or 24 months,
whichever occurs first. Damage caused by the
use of coolant other than DEX-COOL@
is not
covered by your new vehicle warranty.
What to Use
Use a mixture of one-half clean water (preferably
distilled) and one-half
DEX-COOL@ coolant which
won’t damage aluminum parts. If you use this mixture,
you don’t need to add anything else.
I A CAUTION:
Adding only plain water to your cooling system
can
be dangerous. Plain water, or some other
liquid like
alcohol, can boil before the proper
coolant mixture will. Your vehicle’s coolant
warning system is set
for the proper coolant
mixture. With plain water or the wrong mixture,
your engine could get too hot but you wouldn’t
get the overheat warning. Your engine could
catch fire and
you or others could be burned.
Use a
50/50 mixture of clean water and
DEX-COOL@ coolant.
6-28

Don’t use any of these unless this manual says you can.
In many uses, these will damage your vehicle:
Alcohol
Laundry Soap
0 Bleach
Reducing Agents
Cleaning the Inside of Your Vehicle
Use a vacuum cleaner often to get rid of dust and loose
dirt. Wipe vinyl, leather, plastic and painted surfaces with a
clean, damp cloth.
Your dealer has two cleaners, Multi-Purpose Interior
Cleaner and Capture Non-Solvent
Dry Spot and Soil
Remover for cleaning fabric and carpet. They will clean
normal spots and stains very well. You can get
GM-approved cleaning products
from your dealer. (See
“Appearance Care and Materials” in the Index.)
Here are some cleaning tips:
0 Always read the instructions on the cleaner label.
Clean up stains as soon as you can -- before they set.
Carefully scrape off any excess stain.
Use a clean cloth or sponge, and change to a clean area
0 If a ring forms after spot cleaning, clean the entire
often.
A soft brush may be used if stains are stubborn.
area immediately or it
will set.
Using Multi-Purpose Interior Cleaner
on Fabric
1. Vacuum and brush the area to remove any loose dirt.
2. Always clean a whole trim panel or section. Mask
3. Mix powdered cleaner following the directions on
4. Use suds only and apply with a clean sponge. Don’t
5. As soon as you’ve cleaned the section, use a sponge
6. Wipe cleaned area with a clean, damp towel or cloth.
7. Wipe with a clean cloth and let dry.
surrounding trim along stitch or welt lines.
the container label to
form thick suds.
saturate the material and don’t rub it roughly.
to remove the suds.
Special Fabric Cleaning Problems
Stains caused by such things as catsup, coffee (black),
egg, fruit, hit juice,
milk, soft drinks, vomit, urine and
blood
can be removed as follows:
1. Carefully scrape off excess stain, then sponge the
2. If a stain remains, follow the multi-purpose interior
soiled area with cool water.
cleaner instructions described earlier.

Capacities (Approximate)
Air Conditioning? ............. See the refrigerant
Automatic Transmission information label under the hood.
Drain and
Refill ......
Overhaul
VIN Engine Code K .
VIN Engine Code G .
Cooling System
VIN Engine Code K
....... 5 quarts (4.7 L)*
... 8.8 quarts (8.3 L)*
. 10.8 quarts (10.2 L)*
With Manual
With Automatic
VIN Engine Code G
Transmission ............ 12.5 quarts (1 1.8 L)
Transmission ............ 12.3 quarts (1 1.6 L)
With Manual
Transmission
...
With Automatic Transmission
.....
. . 15.3 quarts (14.5 L)
. . 15.1 quarts (14.3 L)
Crankcase
Oil and Filter Change
3800 V6 (VIN K) ......... 4.5 quarts (4.3 L)**
5.7L V8 (VIN G) ......... 5.5 quarts (5.2 L)**
Fuel Tank ................ 15.5 gallons (58.7 L)
Manual Transmission
Five-Speed
................ 3.4 quarts (3.2 L)*
Six-Speed ................... 4 quarts (3.8L)*
Rear Axle Lubricant ............ 1.75 quarts (1.7L)
Not all air conditioning refrigerants are the same.
If the air conditioning system in your vehicle needs
refrigerant, be sure the proper refrigerant is used. If
you’re not sure, ask your Pontiac dealer.
* Recheck fluid level after filling. See “Automatic
Transmission
Fluid” or “Manual Transmission Fluid”
in the Index.
** Recheck the oil level after filling. See “Engine Oil”
in the Index.
6-69

I
KEEP ENGINE OIL
AT THE PROPER I
LEVEL AND CHANGE AS
RECOMMENDED
I
Have you purchased the GM Protection Plan? The Plan
supplements your new vehicle warranties. See your
Warranty and Owner Assistance booklet, or
your
Pontiac dealer for details.
Introduction
Your Vehicle and the Environment
Proper vehicle maintenance not only helps to keep your
vehicle in good working condition, but also helps the
environment. All recommended maintenance procedures
are important. Improper vehicle maintenance can even
affect the
quality of the air we breathe. Improper fluid
levels or the wrong tire
inflation can increase the level
of emissions from your vehicle.
To help protect our
environment, and to keep your vehicle in good
condition, please maintain your vehicle properly.
7-2