remote start PONTIAC G6 2007 User Guide

Temperature Control:Turn the center knob
clockwise or counterclockwise to increase
or decrease the temperature inside your vehicle.
When it’s cold outside 0°F (−18°C) or lower,
use the engine coolant heater, if the vehicle has
one, to warm air faster in your vehicle. An
engine coolant heater warms the engine coolant
that is used to warm the inside of your vehicle. For
more information, seeEngine Coolant Heater on
page 128.
#(Air Conditioning):Press this button to turn
the air conditioning system on or off. When
the air conditioning button is pressed, an indicator
light comes on to indicate that the air conditioning
is activated.
The air conditioning system removes moisture from
the air, so sometimes a small amount of water drips
underneath the vehicle while it is idling or after the
engine is turned off. This is normal.
Maximum Air Conditioning
On hot days, open the windows to let hot inside
air escape; then close them. This helps to reduce
the time it takes for your vehicle to cool down.
It also helps the system to operate more efficiently.For quick cool down on hot days, do the following:
1. Select the
Cvent mode.
2. Select the highest fan speed.
3. Select
#air conditioning.
4. Select the
?recirculation mode.
5. Select the coolest temperature.
Using these settings together for long periods of
time can cause the air inside of your vehicle
to become too dry. To prevent this from
happening, after the air in your vehicle has cooled,
turn the recirculation mode off.
If your vehicle has the remote start feature, it will
turn on using the last settings selected on the
climate control before the vehicle was turned off.
The fan and air delivery knobs can be used during
remote start. The buttons will not work until the
ignition is turned on by the key.
The climate control system changes back to
manual operation when the vehicle key is
turned to ON.
184

Rear Window Defogger
The rear window defogger uses a warming grid to
remove fog or frost from the rear window.
window defogger on or off. An indicator light
comes on to indicate that the rear window
defogger is on. Be sure to clear as much snow as
possible from the rear window.
If driving below 50 mph (80 km/h), the rear window
defogger turns off about 15 minutes after the
button is pressed. If turned on again, the defogger
only runs for about seven and one-half minutes
before turning off. The defogger can also be turned
off by pressing the button again or by turning off
the engine.If your vehicle’s speed is maintained above
50 mph (80 km/h), the rear window defogger
remains on once the button is pressed.
If your vehicle has the remote start feature, the
rear defogger automatically turns on if it is
cold outside. When the vehicle transitions out of
the remote start mode, the rear defogger turns off.
SeeRemote Keyless Entry System Operation
on page 101.
Notice:Do not use anything sharp on the
inside of the rear window. If you do, you could
cut or damage the warming grid, and the
repairs would not be covered by your warranty.
Do not attach a temporary vehicle license,
tape, a decal or anything similar to the
defogger grid.
186

Be careful not to cover the sensor located on
the top of the instrument panel near the
windshield. This sensor regulates air
temperature based on sun load, and also turns
on your headlamps.
Also be careful not to cover the sensor grille
on the lower right side of the climate
control faceplate. This senses the inside
vehicle temperature needed for proper
regulation.
To avoid blowing cold air at start-up in cold
weather, the system delays turning on the fan
until warm air is available. The length of
delay depends on the engine coolant
temperature. Turning the fan knob overrides
this delay and change the fan to a selected
speed.
If your vehicle has the remote start feature, the
climate control display initially shows “AS” in place
of the temperature to indicate the remote start
has been activated. The remote start system turns
on using the last temperature selected before
the vehicle was last turned off.For best performance, turn the fan and mode
knobs to the AUTO position. The fan speed and
air delivery modes will change to achieve the best
comfort.
If the outside air temperature is below 45°F and
the air delivery mode knob is set to AUTO,
the automatic climate control system starts in the
defrost mode to clear the window.
The automatic climate control changes back to
manual operation by turning the vehicle on with
the key.
Manual Operation
You can manually adjust the air delivery mode or
fan speed.
9(Off):Select this position on the fan knob to
turn off the entire climate control system.
Outside air will still enter the vehicle, and be
directed to the oor. This direction can be changed
by changing the mode position. The temperature
can also be adjusted using either the up or
down arrow temperature buttons.
9(Fan):Turn the knob with the fan symbol to
manually adjust the fan speed.
188

Defogging and Defrosting
You can use either defog or front defrost to clear
fog or frost from the windshield.
-(Defog):Use to clear the windows of fog or
moisture. Turn the mode knob to this position
to select this setting. This setting delivers air to the
oor and windshield outlets.
0(Defrost):Turn the mode knob to this position
to defrost the windshield. The system automatically
controls the fan speed if AUTO mode is selected.
If the outside temperature is 40°F (4°C) or
warmer, the air conditioning compressor
automatically runs to help dehumidify the air and
dry the windshield. The air conditioning indicator
light blinks three times if you try to turn off
the compressor while in this mode.
Rear Window Defogger
The rear window defogger uses a warming grid to
remove fog from the rear window.
<(Rear):Press this button to turn the rear
window defogger on or off. An indicator light above
the button comes on to indicate that the rear
window defogger is activated.If driving below 50 mph (80 km/h), the rear window
defogger will turn off about 15 minutes after the
button is pressed. If turned on again, the defogger
will only run for about seven and one-half
minutes before turning off.
If your vehicle’s speed is maintained above
50 mph (80 km/h), the rear window defogger
remains on once the button is pressed.
If your vehicle has the remote start feature, the
rear defogger automatically turns on if it is
cold outside, but the indicator light does not come
on. When the vehicle transitions out of remote
start mode the rear defogger turns off.
Notice:Do not use a razor blade or sharp
object to clear the inside rear window. Do not
adhere anything to the defogger grid lines
in the rear glass. These actions may damage
the rear defogger. Repairs would not be
covered by your warranty.
Outlet Adjustment
Rotate the instrument panel outlets and move the
louvers on the outlets to change the direction
and amount of airow in your vehicle.
191

Passenger Airbag Status Indicator
Your vehicle has the passenger sensing system.
Your instrument panel has a passenger airbag
status indicator.
When the ignition key is turned to ON or START,
the passenger airbag status indicator will light
ON and OFF, or the symbol for on and off,
for several seconds as a system check. If you use
remote start to start your vehicle, if you have
this feature, you may not see the system check.
Then, after several more seconds, the status
indicator will light either ON or OFF, or either the
on or off symbol to let you know the status of
the right front passenger’s frontal airbag.If the word ON or the on symbol is lit on the
passenger airbag status indicator, it means that
the right front passenger’s frontal airbag is enabled
(may inate).
{CAUTION:
If the on indicator comes on when you have
a rear-facing child restraint installed in the
right front passenger’s seat, it means that
the passenger sensing system has not
turned off the passenger’s frontal airbag. A
child in a rear-facing child restraint can be
seriously injured or killed if the right front
passenger’s airbag inates. This is
because the back of the rear-facing child
restraint would be very close to the
inating airbag. Do not use a rear-facing
child restraint in the right front passenger’s
seat if the airbag is turned on.
United StatesCanada
197

AV (Average) SPEED:Press the information
button until AV SPEED is displayed. This shows the
vehicle’s average speed in miles per hour (mph) or
kilometers per hour (km/h).
Press and hold the enter button while AV SPEED is
displayed to reset the average vehicle speed.
OIL LIFE:Press the information button until
OIL LIFE is displayed. The engine oil life system
shows an estimate of the oil’s remaining useful life.
It shows 100% when the system is reset after
an oil change. It will alert you to change the oil on
a schedule consistent with your driving conditions.
Always reset the engine oil life system after an oil
change. SeeEngine Oil Life System on page 328.
In addition to the engine oil life system monitoring
the oil life, additional maintenance is recommended
in the Maintenance Schedule in this manual. See
Scheduled Maintenance on page 431andEngine
Oil on page 325.Personalization
MENU:Press this button while the ignition is ON to
scroll through each of the personalization options in
the following order. To avoid excessive drain on the
battery, it is recommended that the headlamps are
turned off. If the vehicle is moving faster than 2 mph
(3 km/h), the personalization menu options are not
available, except for the UNITS option. All of the
personalization options may not be available on
your vehicle. Only the options available display on
the DIC.
Oil Life Reset
Units Selection (English/Metric)
Remote Start Capability
Horn Chirp During Remote Keyless Entry
Locking
Horn Chirp During Remote Keyless Entry
Unlocking
Exterior Light Flash During Remote Keyless
Entry Locking or Unlocking
Delayed Locking
Automatic Vehicle Unlocking: Specic Doors
211

TRUNK AJAR:This message displays when the
trunk lid is not closed completely. Make sure
that the trunk lid is closed completely. SeeTrunk
on page 113for more information.
DIC Vehicle Personalization
The following personalization options may appear
on your vehicle’s audio display by pressing the
MENU button:
OIL LIFE RESET:When this option is displayed,
you can reset the engine oil life system. To
reset the system, seeEngine Oil Life System on
page 328.
UNITS:When UNITS appears on the display,
press the enter button to move between METRIC
or ENGLISH. When you have made your
choice, press the MENU button to record your
selection. The initial setting from the factory
is English for the United States and metric for
Canada.
If you choose English, all information will be
displayed in English units. For example, distance
in miles and fuel economy in miles per gallon
is displayed.If you choose metric, all information will be
displayed in metric units. For example, distance in
kilometers and fuel economy in liters per
100 kilometers is displayed.
The unit measurement will also change the trip
odometer, temperature, and average fuel economy
displays.
REMOTE START:If your vehicle has this feature,
the remote start option can be enabled or
disabled. When REMOTE START appears on the
display, press the enter button to move between
OFF and ON. When you have made your
choice, press the MENU button to record your
selection. The initial setting from the factory is ON.
LOCK HORN:If your vehicle has Remote
Keyless Entry (RKE), this option which allows the
vehicle’s horn to chirp every time the lock
button on the RKE transmitter is pressed, can be
enabled or disabled. When LOCK HORN
appears on the display, press the enter button to
move between ON and OFF. When you have
made your choice, press the MENU button
to record your selection. The initial setting from
the factory is OFF.
216

xSEEKw:Press the down arrow to go to the
start of the current track if more than eight seconds
have played. If this arrow is pressed more than
once, the player continues moving backward
through the CD.
Press the up arrow to go to the start of the next
track. If this arrow is pressed more than once, the
player continues moving forward through the CD.
If either arrow is held or pressed for more than
two seconds, the CD enters CD scan mode and the
CD plays the rst 10 seconds of each track. Press
either arrow again to stop scanning.
DISP (Display):Press this knob to see how long
the current track has been playing. T, the track
number, and the elapsed time of the track appears
on the display. To change the default on the
display, time or elapsed time, press the knob until
you see the desired display, then hold the knob
for two seconds. The radio produces one beep and
the selected display is now the default. Pressing
this button also displays text on commercially
recorded CDs (if available).AUTO TONE/AUTO EQ (Automatic
Equalization):Press this button to select the
desired equalization setting while playing a
CD. The equalization is automatically recalled
whenever a CD is played. For more information,
see AUTO TONE/AUTO EQ listed previously
in this section.
BAND:Press this button to listen to the radio
while a CD is playing. The inactive CD remains
safely inside the radio for future listening.
SRCE (Source):Press this button to play a CD
or to access a remote device (if installed)
while listening to the radio.
EJECT /
Z(Eject):Press this button to eject a
CD. Eject may be activated with either the
ignition or radio off. CDs may be loaded with the
ignition and radio off if this button is pressed rst.
230

To play the tracks on all of the CDs that are
loaded, in random order, press and hold the
RDM button for more than two seconds.
A beep sounds, RANDOM ALL CDS, and
RDM displays. Press RDM again to turn
off random play. RANDOM OFF displays and
RDM disappears from the display.
xSEEKw:Press the down arrow to go to the
start of the current track, if more than eight seconds
have played. Press the up arrow to go to the
beginning of the next track. If either arrow is held or
pressed more than once, the player continues
moving backward or forward through the CD.
To scan the current CD, press and hold either
SEEK arrow for more than two seconds. The CD
goes to the next track, plays the rst 10 seconds,
then goes to the next track. Press either SEEK
arrow again to stop scanning.
To scan all of the CDs loaded, press and hold either
SEEK arrow for more than four seconds. The CD
goes to the next CD, plays the rst 10 seconds of
the rst track, then goes to the next CD. Press
either SEEK arrow again to stop scanning.DISP (Display):Press this knob to switch
between time, temperature, and the elapsed time
of the track. To change the default on the
display (CD#/Track#/Time,
CD#/Track#/Temperature, or Track#/Elapsed
Time/Temperature), press the knob until you see
the desired display, then hold the knob for
two seconds. The radio produces one beep and
the selected display is now the default.
AUTO TONE/AUTO EQ (Automatic
Equalization):Press this button to select the
desired equalization setting while playing a
CD. The equalization is set whenever a CD is
played. For more information, see “AUTO TONE”
or “AUTO EQ” listed previously in this section.
BAND:Press this button to listen to the
radio when a CD is playing. The inactive CD(s)
remains safely inside the radio for future listening.
SRCE (Source):Press this button to play a
CD or to access the remote device, when listening
to the radio.
242

8. Now connect the black negative (−) cable to
the negative (−) terminal of the good battery.
Use a remote negative (−) terminal if the
vehicle has one.
Do not let the other end touch anything until the
next step. The other end of the negative (−)
cable does not go to the dead battery. It goes to
a heavy, unpainted metal engine part or to a
remote negative (−) terminal on the vehicle with
the dead battery.
9. Connect the other end of the negative (−) cable
at least 18 inches (45 cm) away from the dead
battery, but not near engine parts that move.
The electrical connection is just as good there,
and the chance of sparks getting back to the
battery is much less.
If the security light ashes, wait until the light
stops ashing.
10. Now start the vehicle with the good battery
and run the engine for a while.
11. Try to start the vehicle that had the dead
battery. If it will not start after a few tries,
it probably needs service.Notice:If the jumper cables are connected or
removed in the wrong order, electrical shorting
may occur and damage the vehicle. The repairs
would not be covered by your warranty. Always
connect and remove the jumper cables in the
correct order, making sure that the cables do
not touch each other or other metal.
A. Heavy, Unpainted Metal Engine Part
B. Good Battery
C. Dead Battery
Jumper Cable Removal
360