service PONTIAC G6 2007 Owner's Manual

This light should come on, as a check to show
you it is working, when the ignition is on and the
engine is not running. If the light does not
come on, have it repaired. This light will also
come on during a malfunction in one of two ways:
Light Flashing— A misre condition has
been detected. A misre increases vehicle
emissions and may damage the emission
control system on your vehicle. Diagnosis and
service may be required.
Light On Steady— An emission control
system malfunction has been detected on your
vehicle. Diagnosis and service may be
required.
If the Light is Flashing
The following may prevent more serious damage
to your vehicle:
Reducing vehicle speed
Avoiding hard accelerations
Avoiding steep uphill grades
If you are towing a trailer, reduce the amount
of cargo being hauled as soon as it is
possibleIf the light stops ashing and remains on steady,
see “If the Light Is On Steady” following.
If the light continues to ash, when it is safe to do
so, stop the vehicle. Find a safe place to park
your vehicle. Turn the key off, wait at least
10 seconds and restart the engine. If the light
remains on steady, see “If the Light Is On Steady”
following. If the light is still ashing, follow the
previous steps, and see your dealer for service as
soon as possible.
If the Light Is On Steady
You may be able to correct the emission system
malfunction by considering the following:
Did you recently put fuel into your vehicle?
If so, reinstall the fuel cap, making sure to fully
install the cap. SeeFilling the Tank on page 313.
The diagnostic system can determine if the
fuel cap has been left off or improperly installed.
A loose or missing fuel cap will allow fuel to
evaporate into the atmosphere. A few driving trips
with the cap properly installed should turn the
light off.
205

Oil Pressure Light
If you have a low engine
oil pressure problem,
this light will stay on after
you start your engine, or
come on when you are
driving. This indicates
that your engine is not
receiving enough oil.
The engine could be low on oil, or could have
some other oil problem. Have it xed immediately.
The oil light could also come on in three other
situations:
When the ignition is on but the engine is not
running, the light will come on as a test to
show you it is working, but the light will go out
when you turn the ignition to START. If it
doesn’t come on with the ignition on, you may
have a problem with the fuse or bulb. Have
it xed right away.
If the vehicle is idling at a stop sign, the light
may blink on and then off.
If you make a hard stop, the light may come
on for a moment. This is normal.
{CAUTION:
Do not keep driving if the oil pressure is
low. If you do, your engine can become so
hot that it catches re. You or others
could be burned. Check your oil as soon
as possible and have your vehicle
serviced.
Notice:Lack of proper engine oil maintenance
may damage the engine. The repairs would
not be covered by your warranty. Always follow
the maintenance schedule in this manual for
changing engine oil.
Security Light
For information
regarding this light, see
Theft-Deterrent
Systems on page 118.
207

BRAKE FLUID:This message displays to inform
the driver that the brake uid level is low while the
ignition is in ON. The brake system warning light on
the instrument panel cluster also comes on. See
Brake System Warning Light on page 199for more
information. Have the brake system serviced by
your dealer as soon as possible.
CHANGE OIL SOON:This message displays
when the life of the engine oil has expired and it
should be changed.
When you acknowledge the CHANGE OIL SOON
message by clearing it from the display, you
still must reset the engine oil life system
separately. SeeEngine Oil Life System on
page 328,Engine Oil on page 325, andScheduled
Maintenance on page 431for more information.
CHECK CARGO TOP:If your vehicle has a
retractable hardtop, this message displays if the
cargo divider is not in place when operating
the retractable hardtop. Open the trunk and make
sure the cargo divider is secure and no objects
are on the divider. SeeTrunk on page 113,
Lowering the Retractable Hardtop on page 154,
andRaising the Retractable Hardtop on page 157
for more information.CHECK GAS CAP:This message displays if the
fuel cap has not been fully tightened. Recheck
the fuel cap to make sure that it is on properly.
A few driving trips with the cap properly installed
should turn the message off.
DOOR AJAR:This message displays if one or
more of the vehicle’s doors are not closed
properly. When this message displays, make sure
that the door is closed completely.
ENGINE DISABLED:This message displays if
the starting of the engine is disabled. Have
your vehicle serviced immediately by your dealer.
ENG (Engine) PWR (Power) REDUCED:This
message displays to inform you that the vehicle
has reduced engine power to avoid damaging the
engine. Reduced engine power can affect the
vehicle’s ability to accelerate. If this message is on,
but there is no reduction in performance, proceed
to your destination. The performance may be
reduced the next time the vehicle is driven. The
vehicle may be driven at a reduced speed
while this message is on, but acceleration and
speed may be reduced. Anytime this message
stays on, the vehicle should be taken to your
dealer for service as soon as possible.
213

ICE POSSIBLE:This message displays when the
outside air temperature is cold enough to create
icy road conditions. Adjust your driving accordingly.
KEY FOB BATT (Battery) LOW:This message
displays if the Remote Keyless Entry (RKE)
transmitter battery is low. Replace the battery in
the transmitter. See “Battery Replacement”
underRemote Keyless Entry System Operation on
page 101.
LOW FUEL:This message displays along with a
low fuel warning light on the instrument panel
cluster when your vehicle is low on fuel. Rell the
fuel tank as soon as possible. SeeLow Fuel
Warning Light on page 208,Fuel on page 310,
andFilling the Tank on page 313.
LOW OIL LEVEL:This message may display on
some vehicles. For correct operation of the low oil
sensing system, your vehicle should be on a level
surface. A false LOW OIL LEVEL message may
appear if the vehicle is parked on a grade. The oil
level sensing system does not check for actual oil
level if the engine has been off for a short period of
time. The oil level is never checked while the
engine is running. If the LOW OIL LEVEL message
appears, and your vehicle has been parked on levelground with the engine off for at least 30 minutes,
the oil level should be checked by looking at the oil
dipstick. Prior to checking the oil level, be sure the
engine has been off for a few minutes and your
vehicle is on a level surface. Then check the
dipstick and add oil if necessary. SeeEngine Oil on
page 325.
LOW WASHER FLUID:This message displays
when your vehicle is low on windshield washer
uid. Rell the windshield washer uid reservoir as
soon as possible. See “Adding Washer Fluid”
underWindshield Washer Fluid on page 350.
PARKING BRAKE:This message displays if the
parking brake is left engaged and you try to
drive away. SeeParking Brake on page 135for
more information.
POWER STEERING:This message displays if a
problem has been detected with the electric
power steering, if your vehicle has this feature.
Have your vehicle serviced immediately by
your dealer.
SERVICE AIR BAG:This message displays if
there is a problem with the airbag system.
Have your vehicle serviced immediately by your
dealer.
214

Radio Data System (RDS)
The audio system has a Radio Data System
(RDS). RDS features are available for use only on
FM stations that broadcast RDS information.
With RDS, the radio can do the following:
Seek to stations broadcasting the selected
type of programming
Receive announcements concerning local and
national emergencies
Display messages from radio stations
Seek to stations with traffic announcements
This system relies upon receiving specic
information from these stations and only works
when the information is available. In rare cases, a
radio station can broadcast incorrect information
that causes the radio features to work improperly.
If this happens, contact the radio station.
While the radio is tuned to an RDS station, the
station name or call letters appear on the display
instead of the frequency. RDS stations can
also provide the time of day, a program type (PTY)
for current programming, and the name of the
program being broadcast.
XM™ Satellite Radio Service
XM™ is a satellite radio service that is based in
the 48 contiguous United States and Canada.
XM™ offers a large variety of coast-to-coast
channels including music, news, sports, talk,
traffic/weather (U.S. subscribers), and children’s
programming. XM™ provides digital quality
audio and text information that includes song title
and artist name. A service fee is required in
order to receive the XM™ service. For more
information, contact XM™; In the U.S. at
www.xmradio.com or call 1-800-852-XMXM (9696)
or in Canada at www.xmradio.ca or call
1-877-GET-XMSR (438-9677).
Playing the Radio
O
(Power):Press this knob to turn the system
on and off.
u(Volume):Turn this knob clockwise or
counterclockwise to increase or to decrease the
volume.
222

To adjust both speaker controls to the middle
position, push and hold the tone button while no
speaker control is displayed. ALL CENTERED
displays and One beep sounds. The balance and
fade adjusts to the middle position.
Finding a Program Type (PTY) Station
(RDS and XM™)
To select and nd a desired PTY perform the
following:
1. Press the P-TYPE button to activate program
type select mode. PTY for FM or PTYPE for
XM™ and a program type displays.
2. Turn the ADJ knob to select a PTY.
3. Once the desired PTY is displayed, press the
SEEK up arrow to select the PTY and to take
you to the PTY’s rst station.
4. To go to another station within that PTY press
the SEEK up arrow again. If the radio cannot
nd the desired PTY, NONE FOUND
displays and the radio returns to the last
station you were listening to.
After 15 seconds of inactivity or if the P-TYPE
button is pressed again, the radio exits
program type select mode.BAND (Alternate Frequency):Alternate
frequency lets the radio switch to a stronger
station with the same program type. To turn
alternate frequency on, press and hold BAND for
two seconds. FM ALT FREQ ON and AF
displays. The radio can switch to stations with a
stronger frequency.
To turn alternate frequency off, press and hold
BAND again for two seconds. FM ALT FREQ OFF
displays and AF disappears from the display.
The radio does not switch to other stations.
This function does not apply for XM™ Satellite
Radio Service.
RDS Messages
ALERT!:Alert warns of local or national
emergencies. When an alert announcement
comes on the current radio station, ALERT!
displays. You will hear the announcement, even if
the volume is low or a CD is playing. If a CD is
playing, play stops during the announcement. Alert
announcements cannot be turned off.
226

ALERT! is not affected by tests of the emergency
broadcast system. This feature is not supported
by all RDS stations.
MSG (Message):If the current station has a
message, MSG displays. Press this button to see
the message. The message may display the
artist, song title, call in phone numbers, etc.
If the entire message is not displayed, parts of the
message appears every three seconds. To scroll
through the message, press and release the MSG
button. A new group of words appear on the display
after every press of the button. Once the complete
message has been displayed, MSG disappears
from the display until another new message is
received. The last message can be displayed by
pressing the MSG button. You can view the last
message until a new message is received or a
different station is tuned to.
When a message is not available from a station,
NO MESSAGE displays.TRAF (Traffic):If TRAFFIC displays, the tuned
station broadcasts traffic announcements. When a
traffic announcement broadcasts on the tuned
radio station, you will hear it.
If the station does not broadcast traffic
announcements, press the TRAF button and the
radio seeks to a station that does. When a station
that broadcasts traffic announcements is found, the
radio stops seeking and TRAF in brackets displays.
If no station is found that broadcasts traffic
announcements, NO TRAFFIC INFO displays.
If TRAF is on the display, press the TRAF button to
turn off the traffic announcements.
The radio plays the traffic announcement even if the
volume is low. The radio interrupts the play of a CD
if the last tuned station broadcasts traffic
announcements.
This function does not apply to XM™ Satellite
Radio Service.
227

Radio Messages
CALIBRATE:The audio system has been
calibrated for your vehicle from the factory. If
CALIBRATE displays, it means that the radio has
not been congured properly for your vehicle
and it must be returned to your dealer for service.
LOCKED:This message is displayed when
the THEFTLOCK
®system has locked up. Take
your vehicle to your dealer for service.
If any error occurs repeatedly or if an error cannot
be corrected, contact your GM dealer.
Radio Messages for XM™ Only
SeeXM Radio Messages on page 246later in this
section for further detail.
Playing a CD
Insert a CD partway into the slot, label side up.
The player pulls it in and the CD should begin
playing. If you want to insert a CD with the ignition
off, rst press the eject button or the DISP
(display) knob.
As each new track starts to play, the track number
appears on the display.If the ignition or radio is turned off with a CD in
the player, it stays in the player. When the ignition
or radio is turned on, the CD starts playing,
where it stopped, if it was the last selected audio
source.
The CD player can play the smaller 3 inch (8 cm)
single CDs with an adapter ring. Full-size CDs
and the smaller CDs are loaded in the same
manner.
If playing a CD-R, the sound quality may be
reduced due to CD-R quality, the method of
recording, the quality of the music that has been
recorded, and the way the CD-R has been
handled. There may be an increase in skipping,
difficulty in nding tracks, and/or difficulty in loading
and ejecting. If these problems occur, check the
bottom surface of the CD. If the surface of the CD
is damaged, such as cracked, broken, or
scratched, the CD will not play properly. If the
surface of the CD is soiled, seeCare of Your CDs
on page 250for more information.
If there is no apparent damage, try a known
good CD.
228

Radio Data System (RDS)
The audio system has a Radio Data System
(RDS). RDS features are available for use only on
FM stations that broadcast RDS information.
With RDS, the radio can do the following:
Seek to stations broadcasting the selected
type of programming
Receive announcements concerning local and
national emergencies
Display messages from radio stations
Seek to stations with traffic announcements
This system relies upon receiving specic
information from these stations and only works
when the information is available. In rare cases, a
radio station may broadcast incorrect information
that causes the radio features to work improperly.
If this happens, contact the radio station.
While the radio is tuned to an RDS station, the
station name or call letters appear on the display
instead of the frequency. RDS stations can
also provide the time of day, a program type (PTY)
for current programming, and the name of the
program being broadcast.
XM™ Satellite Radio Service
XM™ is a satellite radio service that is based in
the 48 contiguous United States and Canada.
XM™ offers a large variety of coast-to-coast
channels including music, news, sports, talk,
traffic/weather (U.S. subscribers), and children’s
programming. XM™ provides digital quality
audio and text information that includes song title
and artist name. A service fee is required in
order to receive the XM™ service. For more
information, contact XM™; In the U.S. at
www.xmradio.com or call 1-800-852-XMXM (9696)
or in Canada at www.xmradio.ca or call
1-877-GET-XMSR (438-9677).
Playing the Radio
O
(Power):Press this knob to turn the system
on and off.
u(Volume):Turn this knob to clockwise or
counterclockwise increase or to decrease
the volume.
232

BAND (Alternate Frequency):Alternate
frequency lets the radio switch to a stronger station
with the same program type. To turn alternate
frequency on, press and hold BAND for
two seconds. FM ALT FREQ ON and AF displays.
The radio can switch to stations with a stronger
frequency.
To turn alternate frequency off, press and hold
BAND again for two seconds. FM ALT FREQ OFF
displays and AF disappears from the display. The
radio does not switch to other stations.
This function does not apply for XM™ Satellite
Radio Service.
RDS Messages
ALERT!:Alert warns of local or national
emergencies. When an alert announcement
comes on the current radio station, ALERT!
displays. You will hear the announcement, even if
the volume is low or a CD is playing. If a CD is
playing, play stops during the announcement. Alert
announcements cannot be turned off.
ALERT! is not affected by tests of the emergency
broadcast system. This feature is not supported
by all RDS stations.MSG (Message):If the current station has a
message, MSG displays. Press this button to see
the message. The message may display the
artist, song title, call in phone numbers, etc.
If the entire message is not displayed, parts of the
message appears every three seconds. To
scroll through the message, press and release the
MSG button. A new group of words appear on
the display after every press of this button. Once
the complete message has been displayed,
MSG disappears from the display until another
new message is received. The last message can
be displayed by pressing the MSG button.
You can view the last message until a new
message is received or a different station is
tuned to.
When a message is not available from a station,
NO MESSAGE displays.
MSG (Traffic):If TRAFFIC displays, the tuned
station broadcasts traffic announcements. When a
traffic announcement broadcasts on the tuned
radio station, you will hear it.
237