switch PONTIAC GRAND AM 1997 Owners Manual

Manual Lumbar Support (If Equipped) Power
Seat Controls (If Equipped)
Turn the knob on the right front of the driver’s seat
cushion clockwise or counterclockwise to adjust support
for the lower back. To adjust the power seat on some models:
FRONT CONTROL (A): Raise the front of the seat by
holding the switch up. Lower the front
of the seat by
holding the switch down.
CENTER CONTROL (B): Move the seat forward or
back
by holding the control to the front or back.
Move the seat higher by holding the control up. Lower
the seat by holding the control down.
REAR CONTROL (C): Raise the rear of the seat by
holding the switch up. Lower the rear of the seat by
holding the switch down.
1-3

Power Door Locks
With power door locks, you
can lock or unlock all the
doors of your vehicle from
the driver or front passenger door lock switch.
On four-door models, slide the lock lever on each rear
door to lock or unlock that door.
Automatic Door Locks
Just close your doors and turn on the ignition. If you
have an automatic transaxle, all of the doors will lock
when
you move your shift lever out of PARK (P) or
NEUTRAL (N). If you have a manual transaxle, all
of the doors will lock when the vehicle reaches about
8 mph (13 km/h). If someone needs to get out while the
vehicle is running, have that person use the manual or
power lock. When the door is closed again,
it will lock
automatically when you move your shift lever out
of
PARK (P) or NEUTRAL (N). If you have a manual
transaxle, the doors will lock when the vehicle reaches about
8 mph (13 km/h). All doors will automatically
unlock when the key
is turned to the OFF position.
If you don’t want the doors to automatically unlock
when the key
is turned to the OFF position, you can
remove the DR UNLK fuse (1OA) from the vehicle fuse
block. For fuse location, see “Fuses and Circuit
Breakers” in the Index.
2-5

Operation
The following functions are available with the Keyless
Entry System:
LOCK: All doors will automatically lock when the
LOCK button on the transmitter is pressed. The interior
lamps stay on for two seconds after all of the doors
are closed.
UNLOCK: The driver’s door will unlock automatically
when the UNLOCK button on the transmitter is pressed.
If the UNLOCK button is pressed again within five
seconds, all remaining doors will unlock. The interior
lamps will stay on for
40 seconds or until the ignition is
turned on.
Trunk Release: The trunk will unlock anytime the
vehicle symbol
on the transmitter is pressed and the
ignition is
OW. If the ignition is on, the trunk will
unlock
if the parking brake is set (manual transaxle) or
the gear selector
is in PARK (P) or NEUTRAL (N)
(automatic transaxle). The interior lamps will come on
for 40 seconds or until the ignition switch is turned to
the
ON position.
Matching Transmitter(s) To Your Vehicle
Each key chain transmitter is coded to prevent another
transmitter from unlocking your vehicle.
If a transmitter
is lost or stolen, a replacement can be purchased through
your dealer. Remember to bring any remaining
transmitters with you when you go to your dealer. When
the dealer matches the replacement transmitter to your
vehicle, any remaining transmitters must also be
matched. Once your dealer has coded the new
transmitter, the lost transmitter will not unlock your
vehicle. Each vehicle can have only two transmitters
matched to it.
You can match your transmitter to as many 1997
General Motors vehicles as you own, as long as they
have the same Keyless Entry System. Contact your
dealer for assistance with this.
2-8

Remote Trunk Release
The remote trunk release handle is located on the floor
near the left side of the driver’s seat in front of the
fuel door release. Pull up on the remote release handle to
release the trunk lid. Make sure the override feature is
not activated.
Trunk Security Override
The remote trunk release is
equipped with an override
feature to help prevent
unauthorized entry into the
trunk when leaving the
vehicle unattended, The switch is located on the
inside of the trunk lid,
mounted to the trunk
lid latch.
To turn the override feature on, slide the switch all the
way to the right. To turn the override feature off, slide
the switch all the way to the left.
When the override is on, the mechanical remote trunk
release will not release the trunk lid, However, the
trunk
lid can still be opened with the key.
This lockout feature
is only available on vehicles that do
not have the Keyless Entry System.
2-11

Ignition Positions
A-
C
i
With the key in the ignition switch, you can turn the
switch to five positions.
ACCESSORY (A): This position lets you use things
like the radio and windshield wipers when the engine is
off. To use
ACCESSORY, push in the key and turn it
toward you. Your steering wheel will stay locked.
LOCK (B): Before you put the key into the ignition
switch, the switch is
in LOCK. It’s also the only position
in which you can remove the key. This locks your steering
wheel, ignition and transaxle (on automatic models).
OFF (C): This position unlocks the steering wheel and
ignition, but does not send electrical power to any
accessories. Use this position if your vehicle must be
pushed or towed, but never try to push-start your
vehicle.
A warning chime will sound if you open the
driver’s door when the ignition is off and the key is in
the ignition.
RUN (D): This position is where the key returns after
you start your engine and release the switch. The switch
stays in the
RUN position when the engine is running.
But even when the engine is not running, you can use
RUN to operate your electrical power accessories, and
to display some instrument panel warning lights.
2-14

START (E): This position starts your engine. When the
engine starts, release the key. The ignition switch will
return to RUN
for normal driving.
Note that even if the engine is not running, the positions
ACCESSORY and
RUN are on positions that allow you
to operate your electrical accessories, such as the radio.
On manual transaxle vehicles, turning the key to
LOCK will lock the steering column and result in
a loss of ability to steer the vehicle. This could
cause
a collision, If you need to turn the engine
off while the vehicle is moving, turn the key only
to
OFF. Don’t press the key release button while
the vehicle is moving.
NOTICE:
If your key seems stuck in LOCK and you can’t
turn it, be sure you are using the correct key; if
so, is it all the way in? If it is, then turn the
steering wheel left and right while you turn the
key
hard. But turn the key only with your hand.
Using
a tool to force it could break the key or the
ignition switch.
If none of this works, then your
vehicle needs service.
2-15

Running Your Engine While You’re
Parked (Automatic Transaxle)
It’s better not to park with the engine running. But if you
:ver have to, here are some things
to know.
h
A CAUTION:
Idling the engine with the climate control system
off could allow dangerous exhaust into your vehicle
(see the earlier Caution under “Engine Exhaust”),
Also, idling in a closed-in place can let deadly
carbon monoxide (CO) into your vehicle even if
the fan switch is at the highest setting. One place
this can happen is
a garage. Exhaust -- with
CO
-- can come in easily. NEVER park in a
garage
with the engine running.
Another closed-in place can be a blizzard, (See
“Blizzard” in the Index.)
I
A CAUTION:
It can be dangerous to get out of your vehicle if
the shift lever is not fully in PARK (P) with the
parking brake firmly set. Your vehicle can roll.
Don’t leave your vehicle when the engine is
running unless you have to.
If you’ve left the
engine running, the vehicle can move suddenly.
You or others could be injured. To be sure your
vehicle won’t move, even when you’re on fairly
level ground, always set your parking brake and
move the shift lever to PARK (P).
Follow the proper steps to be sure your vehicle won’t
move. See “Shifting Into
PARK (P)” in the Index.
If you are parking on a hill and if you’re pulling a
trailer, also see “Towing a Trailer” in the Index.
2-33

Windows
On a vehicle with manual windows, use the window
crank located on the inside of each door to open and
close each window.
Power Windows (If Equipped)
The power window switches are located on the door
armrests; the driver’s door armrest has controls for all
of
the windows. These switches will only work when the
ignition is on.
Auto-Down Feature
The driver’s window switch has an auto-down feature.
This switch is labeled AUTO. Tap the switch back, and
the driver’s window will open a small amount. When the switch is moved all the way back, the window will go
down all the way.
To stop the window while it
is lowering, move the
switch forward.
To raise the window, move and hold the
switch forward.
Lock-Out Switch
On four-door models, the driver’s power window
controls also include a lock-out switch. Press
LOCK to
stop front and rear passengers
from using their window
switches. The driver can still control all the windows
with the lock
on. Press the other side of the LOCK
button for normal window operation.
Horn
Press the center of your steering wheel to sound
the horn.
2-34

Setting Cruise Control
A CAUTION:
If you leave your cruise control switch on when
you’re not using cruise,
you might hit a button
and go into cruise when
you don’t want to. You
could be startled and even lose control. Keep the
cruise control switch
OFF until you want to
use it.
1. Move the cruise control switch to ON.
2. Get up to the speed you want. 3. Push in the SET button at the end of the lever and
release
it.
4. Take your foot off the accelerator pedal.
2-40

Resuming a Set Speed
Suppose you set your cruise control at a desired speed
and then you apply the brake. This, of course, shuts
off the cruise control. But you don’t need to reset it.
Once you’re going about
25 mph (40 h/h) or more,
you can move the cruise control switch from
ON to
R/A (Resume/Accelerate) for about half a second.
You’ll go right back up to your chosen speed and stay there. If you
hold the switch at R/A longer than half a second,
the vehicle will keep going faster until you release the
switch or apply the brake, or clutch pedal (if you have a
manual transaxle).
You could be startled and even lose
control,
So unless you want to go faster, don’t hold the
switch to R/A.
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed.
Use the accelerator pedal to get to the higher speed. Push the
SET button at the end of the lever, then
release the button and the accelerator pedal. You’ll now cruise at the higher speed.
Move the cruise switch from ON to R/A. Hold it
there until you get up to the speed you want, and
then release the switch.
(To increase your speed in
very small amounts, move the switch to R/A for
less than half a second and then release it. Each
time you do this, your vehicle will go about
1 mph (1.6 km/h) faster.)
2-41