clock PONTIAC GRAND PRIX 2007 User Guide

Filling the Tank
{CAUTION:
Fuel vapor burns violently and a fuel re
can cause bad injuries. To help avoid
injuries to you and others, read and follow
all the instructions on the pump island.
Turn off your engine when you are
refueling. Do not smoke if you are near
fuel or refueling your vehicle. Keep
sparks, ames, and smoking materials
away from fuel. Do not leave the fuel
pump unattended when refueling your
vehicle. This is against the law in some
places. Keep children away from the fuel
pump; never let children pump fuel.The tethered fuel cap is located behind a hinged
fuel door on the driver’s side of the vehicle.
To remove the fuel cap, turn it slowly
counterclockwise. The fuel cap has a spring in it; if
the cap is released too soon, it will spring back
to the right.
While refueling, let the fuel cap hang by the tether
below the fuel ll opening.
342

{CAUTION:
If you spill fuel and then something
ignites it, you could be badly burned. Fuel
can spray out on you if you open the fuel
cap too quickly. This spray can happen if
your tank is nearly full, and is more likely
in hot weather. Open the fuel cap slowly
and wait for any hiss noise to stop. Then
unscrew the cap all the way.
Be careful not to spill fuel. Do not top off or overll
the tank and wait a few seconds after you have
nished pumping before removing the nozzle.
Clean fuel from painted surfaces as soon
as possible. SeeWashing Your Vehicle on
page 453.
When replacing the fuel cap, turn it clockwise until
it clicks. Make sure the cap is fully installed.
The diagnostic system can determine if the fuel
cap has been left off or improperly installed.
This would allow fuel to evaporate into the
atmosphere. SeeMalfunction Indicator Lamp on
page 180.The CHECK GAS CAP message will be displayed
on the Driver Information Center (DIC) if the
fuel cap is not properly installed. SeeDIC
Warnings and Messages on page 200for more
information.
{CAUTION:
If a re starts while you are refueling, do
not remove the nozzle. Shut off the ow of
fuel by shutting off the pump or by
notifying the station attendant. Leave the
area immediately.
Notice:If you need a new fuel cap, be sure to
get the right type. Your dealer can get one
for you. If you get the wrong type, it may not
t properly. This may cause your malfunction
indicator lamp to light and may damage
your fuel tank and emissions system. See
Malfunction Indicator Lamp on page 180.
343

When the coolant level in the coolant recovery
tank is at the cold ll line, start the vehicle.
If the overheat warning continues, there is one
more thing you can try. You can add the proper
coolant mixture directly to the radiator, but be sure
the system is cool before you do it.
{CAUTION:
Steam and scalding liquids from a hot
cooling system can blow out and burn
you badly. They are under pressure, and if
you turn the pressure cap — even a
little — they can come out at high speed.
Never turn the cap when the cooling
system, including the pressure cap, is hot.
Wait for the cooling system and pressure
cap to cool if you ever have to turn the
pressure cap.
How to Add Coolant to the Radiator
(3800 V6 Engines)
Notice:Your engine has a specic radiator ll
procedure. Failure to follow this procedure
could cause your engine to overheat and be
severely damaged.
1. You can remove the pressure cap when the
cooling system, including the pressure cap
and upper radiator hose, is no longer hot. Turn
the cap slowly counterclockwise.
3800 V6 Supercharged Engine shown,
3800 V6 Engine similar
370

If you hear a hiss, wait for that to stop. A hiss
means there is still some pressure left.
2. Then keep turning the pressure cap and
remove it.
{CAUTION:
You can be burned if you spill coolant on
hot engine parts. Coolant contains
ethylene glycol and it will burn if the
engine parts are hot enough. Do not spill
coolant on a hot engine.3. Remove the Series III V6 engine cover shield
to access the bleed valve.
3.1. Clean the area around the engine oil ll
tube and cap before removing. Twist
the oil ll tube, with cap attached,
counterclockwise and remove it.
3800 V6 Engine
371

5. Fill the radiator with the proper DEX-COOL®
coolant mixture, up to the base of the ller
neck. SeeEngine Coolant on page 360
for more information about the proper coolant
mixture.
If you see a stream of coolant coming from the
air bleed valve, close the valve. Otherwise,
close the valve after the radiator is lled.6. Rinse or wipe any spilled coolant from the
engine and the compartment.
7. Replace the 3800 Series III V6 engine cover
shield.
7.1. Remove the oil ll tube, with cap
attached, from the valve cover.
7.2. Insert the catch tab on the cover shield
under the bracket on the engine.
7.3. Place the hole in the cover shield over
the hole in the valve cover. Install oil ll
tube and cap by twisting clockwise.
8. Then ll the coolant recovery tank to the cold
ll line.
9. Put the cap back on the coolant recovery
tank, but leave the pressure cap off.
3800 V6 Supercharged Engine shown,
3800 V6 Engine similar
373

You can remove the
pressure cap when the
cooling system,
including the pressure
cap and upper
radiator hose is no
longer hot. Turn
the pressure cap slowly
counterclockwise.
1. If you hear a hiss, wait for that to stop. A hiss
means that there is still some pressure left.
2. Then keep turning the pressure cap to remove
the pressure cap.
{CAUTION:
You can be burned if you spill coolant on
hot engine parts. Coolant contains
ethylene glycol and it will burn if the
engine parts are hot enough. Do not spill
coolant on a hot engine.3. Fill the cooling system with the proper
DEX-COOL
®coolant mixture, up to the base
of the ller neck. SeeEngine Coolant on
page 360for more information about
the proper coolant mixture.
4. Rinse or wipe any spilled coolant from the
engine and the compartment.
5. Then ll the coolant recovery tank to the cold
ll line.
6. Install the coolant recovery tank cap and the
pressure cap.
7. If the coolant in the recovery tank is constantly
low, you should have a dealership service
department inspect your vehicle for leaks.
375

7. Locate the vertical headlamp aiming screws,
which are under the hood, near the
headlamps. Turn the vertical aiming screw
until the headlamp beam is aimed to the
horizontal tape line.
The adjustment screws can be turned with a
6 mm hex key bit socket ora6mmhexkey.8. Turn the vertical aiming screw until the
headlamp beam is aimed to the horizontal
tape line. Turn it clockwise or
counterclockwise to raise or lower the angle
of the beam.
9. Make sure that the light from the headlamp is
positioned at the bottom edge of the horizontal
tape line. The lamp on the left (A) shows
the correct headlamp aim. The lamp on the
right (B) shows the incorrect headlamp aim.
10. Repeat Steps 7 through 9 for the opposite
headlamp.
Driver’s Side shown
390

A. High-Beam Headlamp
B. Low-Beam Headlamp
C. Sidemarker Lamp5. Turn the bulb socket ring one-quarter of a turn
counterclockwise to remove it from the
headlamp assembly.
6. Pull the old bulb from the socket.
7. Place the new bulb into the socket.
8. Turn the bulb socket ring one-quarter turn
clockwise to reinstall it back into the
headlamp assembly.
9. Carefully reinstall the headlamp assembly.
10. Push down on the metal retaining clip
while pushing rearward on the headlamp,
making sure the headlamp assembly is
secure.
11. Reinstall the bolt and tighten to secure.
393

3. Turn the bulb socket one-quarter of a turn
counterclockwise to remove it from its
assembly.
4. Pull the old bulb from the socket and replace
it with a new one.
5. Turn the bulb socket a quarter turn clockwise
to reinstall it.
6. Reinstall the headlamp assembly.
7. Push down on the metal retaining clip while
pushing rearward on the headlamp, making
sure the headlamp assembly is secure.
8. Reinstall the bolt and tighten to secure.Taillamps, Turn Signal, and
Stoplamps
A. Taillamp
B. Taillamps, Turn
Signal and Stoplamps
1. Open the trunk. SeeTrunk on page 96for
more information.
2. Remove the convenience net, if equipped, by
removing the net hook attachments.
3. Remove the plastic cap from the trunk trim.
4. Pull the trunk trim and carpet away from
the back of the trunk.
5. Remove the bottom bolt and two nuts.
395

6. Remove the taillamp
assembly by pulling
it out from the
vehicle.7. Turn the appropriate
lamp socket a
quarter turn
counterclockwise
and remove it.
8. Remove the old bulb.
9. Replace with a new bulb into the socket and
turn the lamp socket clockwise to install it.
10. Reinstall the taillamp assembly by reversing
Steps 2 through 5.
396