ignition PONTIAC GRAND PRIX 2007 User Guide

The vehicle’s hood is open.
The hazard warning ashers are on.
There is an emission control system
malfunction.
The engine coolant temperature is too high.
The oil pressure is low.
Two remote vehicle starts have already been
provided for that ignition cycle.
If a remote start is attempted and is unsuccessful,
the Driver Information Center (DIC) will display
REMOTE START DISABLED.
Vehicles that have the remote vehicle start feature
are shipped from the factory with the remote start
system enabled. The system may be enabled/
disabled through the DIC. See “REMOTE START”
underDIC Controls and Displays (Base Level DIC)
on page 186orDIC Controls and Displays (Uplevel
DIC with Trip Computer) on page 190for additional
information.
Remote Start Ready
If your vehicle does not have the remote vehicle
start feature, it may have the remote start
ready feature. This feature gives you the ability tolock or unlock your vehicle from about 492 feet
(150 m) away and allows your dealer to add
the manufacturer’s remote vehicle start feature.
See your dealer if you would like to add the
manufacturer’s remote vehicle start feature to
your vehicle.
Doors and Locks
Door Locks
{CAUTION:
Unlocked doors can be dangerous.
Passengers, especially children, can
easily open the doors and fall out of a
moving vehicle. When a door is
locked, the handle will not open it.
You increase the chance of being
thrown out of the vehicle in a crash if
the doors are not locked. So, wear
safety belts properly and lock the
doors whenever you drive.
CAUTION: (Continued)
92

Power Door Locks
To lock or unlock all
doors from inside the
vehicle, use the
power door lock switch
located on either
front door.
Move the switch on the driver’s door to the right to
lock or to the left to unlock the doors. Move the
switch on the passenger’s door to the left to lock or
to the right to unlock the doors.
If the vehicle has the content theft-deterrent
system, the vehicle may be programmed to arm
the system with the power door lock switch.
See “Lock Switch Arm” underDIC Vehicle
Customization on page 226for more information
on programming the system.
Delayed Locking
This feature delays the locking of the vehicle’s
doors for ve seconds after the last door is closed.
Two chimes will sound when the power door
lock switch or the LOCK button on the remote
keyless entry transmitter is pressed when a door
is open. The chimes indicate that the delayed
locking feature is on.
The doors can be locked immediately by pressing
the power door lock switch or the LOCK button
on the transmitter a second time.
The delayed locking feature will not activate when
the ignition is in RUN or ACC.
You can program this feature on or off through the
Driver Information Center (DIC) See “Personal
Programming Mode Screens” underDIC Vehicle
Customization on page 226.
Driver’s Side
94

When you want to open a rear door when the
security lock is on, do the following:
1. Unlock the door using the remote keyless
entry transmitter, if equipped, the power
door lock switch, or by lifting the rear door
manual lock.
2. Open the door from the outside.
To cancel the rear door security lock, do the
following:
1. Unlock the door and open it from the outside.
2. Insert the key into the security lock slot
and turn it so the slot is in the vertical position.
Lockout Protection
The lockout protection feature makes it more
difficult to lock the key in the vehicle. If the driver’s
door is open while the key is in the ignition, the
door cannot be locked with the power door
lock switch.
This feature cannot guarantee that you will never be
locked out of the vehicle. If the key is not left in the
ignition, or, if the manual door lock pin is used, the
key could still be locked inside the vehicle. Always
remember to take the key with you.
Trunk
{CAUTION:
It can be dangerous to drive with the trunk
lid open because carbon monoxide (CO)
gas can come into your vehicle.
You cannot see or smell CO. It can cause
unconsciousness and even death. If you
must drive with the trunk lid open or if
electrical wiring or other cable connections
must pass through the seal between the
body and the trunk lid:
Make sure all other windows are shut.
Turn the fan on your heating or cooling
system to its highest speed and select
the control setting that will force
outside air into your vehicle. See
Climate Control System.
If you have air outlets on or under
the instrument panel, open them all
the way.
SeeEngine Exhaust on page 119.
96

Power Windows
Use the switches on the
driver’s door to operate
each of the windows.
Push the switch down or up to open or close the
window. The top switches operate the front
windows, and the bottom switches operate the
rear windows.
Each passenger door also has a switch, located
on the armrest, that operates that window.
Push the switch rearward or forward to open or
close the window.
The power window switches only work if the ignition
is on or in ACC, or while Retained Accessory
Power (RAP) is active. SeeRetained Accessory
Power (RAP) on page 106for more information.
Express-Down Window
The driver’s window switch has an express-down
feature. This allows the window to open fully without
having to continuously hold the switch. Tap the
switch down, and the driver’s window will open a
small amount. Press the switch fully down and
release and the window will go all the way down.
To stop the window while it is lowering, press the
bottom of the switch. To raise the window,
press and hold the bottom of the switch.
Window Lockout
o
(Window Lockout):The driver’s window
switch includes a lockout feature located above
the power window switches on the driver’s
door. Move the switch to the right to prevent the
passengers sitting in the rear from using their
window switches. The driver can still control all the
windows with the lockout on. Move the switch to
the left to disengage the lockout feature.
99

Arming with the Power Lock Switch
The vehicle’s content theft-deterrent alarm system
can be activated when the key is removed from
the ignition and the power door lock switch
of either the driver’s or front passenger’s door is
used to lock the vehicle. The door needs to
be in the open position when pressing the power
door lock switch. The alarm system will not
activate if the door is closed and the power door
lock switch is pressed. This system can be
activated through the Driver’s Information
Center (DIC). See “Lock Switch Arm” under the
Personal Programming Mode Screens inDIC
Vehicle Customization on page 226.
When the doors are locked using the power door
lock switch of either front door, the red light,
on top of the instrument panel will start ashing
indicating that the system is arming. After all
the doors are closed there will be a time delay and
then the red light will begin to ash at a very
slow rate indicating the system is armed.
Arming with the Remote Keyless Entry
Transmitter
The alarm system will arm when the remote keyless
entry transmitter is used to lock the doors after the
key is removed from the ignition. The red light will
come on to indicate that the system is arming. After
all doors are closed and locked, and after a time
delay, the red light will begin ashing at a very slow
rate to show the system is armed.
Arming Conrmation
A red light located on top of the instrument panel,
towards the center of the vehicle and near the
windshield, will ash slowly to conrm when
the system is armed.
Disarming with the Remote Keyless
Entry Transmitter
The alarm system will disarm when the remote
keyless entry transmitter is used to unlock
the doors. The red light will go out to show that
the system is disarmed.
101

PASS-Key®III Operation
The vehicle is
equipped with
PASS-Key
®III
(Personalized
Automotive Security
System) theft-deterrent
system. PASS-Key
®III
is a passive
theft-deterrent
system.
This means nothing special needs to be done to
arm or disarm the system. It works when the key is
inserted or removed from the ignition.
PASS-Key
®III uses a transponder in the ignition
key that matches a decoder in the vehicle.
When the PASS-Key
®III system senses that the
wrong key has been inserted into the ignition, it
shuts down the vehicle’s starter and fuel systems.The starter will not work and fuel will stop owing to
the engine. If someone tries to start the vehicle
again with the wrong key, the vehicle will not start.
Anyone using a trial-and-error method to start the
vehicle will be discouraged to do so because of the
high number of electrical key codes.
When trying to start the vehicle, if the engine does
not start and the STARTING DISABLED DUE TO
THEFT SYSTEM warning message on the Driver
Information Center (DIC) comes on, the key may
have a damaged transponder. Turn the ignition off
and try again.
If the engine still does not start, and the key
appears to be undamaged, try another ignition key.
At this time, you may also want to check the fuse.
SeeFuses and Circuit Breakers on page 460.Ifthe
engine still does not start with the other key, the
vehicle needs service. If the vehicle does start, the
rst key may be faulty. See your dealer who can
service the PASS-Key
®III to have a new key made.
In an emergency, contact Roadside Assistance.
SeeRoadside Assistance Program on page 498for
more information.
103

It is possible for the PASS-Key®III decoder
to accept the transponder value of a new or
replacement key. Up to 10 keys may be
programmed for the vehicle. If all the programmed
keys are lost or do not operate, see your GM dealer
or a locksmith who can service PASS-Key
®III to
have keys made and programmed to the system.
Canadian Owners: If all the keys are lost or
damaged, only a GM dealer can service
PASS-Key
®III to have new keys made and
programmed to the system.
The following procedure is for programming a new
or replacement key when you have at least one
already programmed key. To program the new key
do the following:
1. Verify that the new key has PK3 stamped on it.
2. Insert the master key in the ignition and start
the engine. If the engine will not start, see
your dealer for service.
3. After the engine has started, turn the key to
OFF, and remove the key.4. Insert the key to be programmed and turn it to
RUN within ve seconds of removing the
original key.
5. The STARTING DISABLED DUE TO THEFT
SYSTEM warning message on the DIC will
turn off, once the key has been programmed.
It may not be apparent that the SERVICE
THEFT SYSTEM warning message went on
due to how quickly the key is programmed.
6. Repeat Steps 1 through 5 if additional keys
are to be programmed.
If the STARTING DISABLED DUE TO THEFT
SYSTEM warning message appears and stays on
the DIC while the vehicle is being driven, the
engine will be able to be restarted if it is turned
off. Your PASS-Key
®III system, however, is
not working properly and must be serviced by
your dealer. The vehicle is not protected by
the PASS-Key
®III system at this time.
If the PASS-Key
®III key is lost or stolen, see
your dealer or a locksmith who can service
PASS-Key
®III to have a new key made.
104

Starting and Operating Your
Vehicle
New Vehicle Break-In
Notice:Your vehicle does not need an
elaborate break-in. But it will perform better in
the long run if you follow these guidelines:
Do not drive at any one constant speed, fast
or slow, for the rst 500 miles (805 km).
Do not make full-throttle starts. Avoid
downshifting to brake, or slow, the vehicle.
Avoid making hard stops for the rst
200 miles (322 km) or so. During this time
your new brake linings are not yet broken
in. Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking-in guideline every time
you get new brake linings.
Do not tow a trailer during break-in. See
Towing a Trailer on page 324for the trailer
towing capabilities of your vehicle and more
information.
Following break-in, engine speed and load can
be gradually increased.
Ignition Positions
The ignition switch is located on the instrument
panel, to the right of the steering column.
There are four different
positions. Insert the key
in the ignition and
turn it to the right for
each position.
9(OFF):This position locks the ignition,
steering wheel and transaxle. It is a theft-deterrent
feature. This is the only position from which the
key can be removed.
Notice:Using a tool to force the key from the
ignition switch could cause damage or break
the key. Use the correct key and turn the key
only with your hand. Make sure the key is all the
way in. If it is, turn the steering wheel left and
right while you turn the key hard. If none of this
works, then your vehicle needs service.
105

ACC (ACCESSORY):This position allows things
like the radio and windshield wipers to operate
while the engine is off.
R(RUN):This position is where the key returns
to after the vehicle is started. With the engine
off, the RUN position displays some of the warning
and indicator lights.
The battery could be drained if you leave the key
in the ACC or RUN position with the engine
off. You may not be able to start your vehicle if
the battery is allowed to drain for an extended
period of time.
/(START):This position starts the engine. Let
go of the key when the engine starts. The key will
return to the RUN for normal driving.
A continuous warning chime will sound and a KEY
IN IGNITION message will display on the Driver
Information Center (DIC) if the key is turned
to OFF or ACC and the driver’s door is opened.
Key In the Ignition
Never leave your vehicle with the keys inside, as it
is an easy target for joy riders or thieves. If you
leave the key in the ignition and park your vehicle,
a chime will sound, when you open the driver’s
door. Always remember to remove your key from
the ignition and take it with you. This will lock
your ignition and transaxle. Also, always remember
to lock the doors.
The battery could be drained if you leave the key
in the ignition while your vehicle is parked.
You may not be able to start your vehicle after it
has been parked for an extended period of time.
Retained Accessory Power (RAP)
If the vehicle has Retained Accessory
Power (RAP), certain features will continue to
operate for up to 10 minutes after the ignition key
is turned to OFF unless a door is opened.
106

Starting the Engine
Place the transaxle in the proper gear.
Move your shift lever to PARK (P) or
NEUTRAL (N). Your engine will not start in
any other position — this is a safety feature.
To restart when you are already moving,
use NEUTRAL (N) only.
Notice:Shifting into PARK (P) with the vehicle
moving could damage the transaxle. Shift into
PARK (P) only when your vehicle is stopped.
Starting Procedure
1. With your foot off the accelerator pedal, turn
the ignition key to START. When the engine
starts, let go of the key. The idle speed will go
down as your engine gets warm. Do not
race the engine immediately after starting it.
Operate the engine and transaxle gently
to allow the oil to warm up and lubricate all
moving parts.Your vehicle has a Computer-Controlled
Cranking System. This feature assists in
starting the engine and protects components.
If the ignition key is turned to the START
position, and then released when the engine
begins cranking, the engine will continue
cranking for a few seconds or until the vehicle
starts. If the engine does not start and the
key is held in START for many seconds,
cranking will be stopped after 15 seconds to
prevent cranking motor damage. To prevent
gear damage, this system also prevents
cranking if the engine is already running.
Engine cranking can be stopped by turning the
ignition switch to the ACC or OFF position.
Notice:Cranking the engine for long periods
of time, by returning the key to the START
position immediately after cranking has ended,
can overheat and damage the cranking
motor, and drain the battery. Wait at least
15 seconds between each try, to allow
the cranking motor to cool down.
107