ignition PONTIAC GRAND PRIX 2008 User Guide

Your vehicle may have
a red light located on top
of the instrument panel,
toward the center of
the vehicle and near
the windshield, that will
ash slowly when the
system is armed.
The theft-deterrent alarm system needs to be
activated through the Driver’s Information Center (DIC).
See “Theft Deterrent” under the Personal Programming
Mode Screens inDIC Vehicle Customization on
page 3-89. While armed, the doors will not unlock with
the power door lock switch. The remote alarm will
sound if someone tampers with the trunk or enters
the vehicle without using the Remote Keyless
Entry (RKE) transmitter or key to unlock the doors.
The horn will sound and the headlamps will ash for
up to two minutes. The system will also cut off the fuel
supply, preventing the vehicle from being driven.Arming with the Power Lock Switch
The vehicle’s content theft-deterrent alarm system
can be activated when the key is removed from
the ignition and the power door lock switch of either
the driver’s or front passenger’s door is used to lock
the vehicle. The door needs to be in the open
position when pressing the power door lock switch.
The alarm system will not activate if the door is
closed and the power door lock switch is pressed.
This system can be activated through the Driver’s
Information Center (DIC). See “Lock Switch Arm”
under the Personal Programming Mode Screens in
DIC Vehicle Customization on page 3-89.
When the doors are locked using the power door
lock switch of either front door, the red light, if your
vehicle has one, will start ashing indicating that
the system is arming. After all the doors are closed
there will be a time delay and then the red light,
if your vehicle has one, will begin to ash at a very
slow rate indicating the system is armed.
2-19

Arming with the RKE Transmitter
The alarm system will arm when the RKE transmitter
is used to lock the doors after the key is removed
from the ignition. The red light, if your vehicle has
one, will come on to indicate that the system is
arming. After all doors are closed and locked,
and after a time delay, the red light, if your vehicle
has one, will begin ashing at a very slow rate
to show the system is armed.
Arming Conrmation
Your vehicle may have a red light located on top
of the instrument panel, towards the center of the
vehicle and near the windshield, that will ash
slowly to conrm when the system is armed.
Disarming with the RKE Transmitter
The alarm system will disarm when the RKE transmitter
is used to unlock the doors. The red light, if your
vehicle has one, will go out to show that the system
is disarmed.
Disarming with Your Key
The alarm system will disarm when the key is used
to unlock the doors. The red light, if your vehicle has
one, will stop ashing when the system is disarmed.
If you would like the key to disarm the alarm system,
see “Personal Programming Mode Screens” under
DIC Vehicle Customization on page 3-89for more
information.
PASS-Key®III Electronic
Immobilizer
Your PASS-Key III system operates on a radio
frequency subject to Federal Communications
Commission (FCC) Rules and with Industry Canada.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
2-20

This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation of the device.
Changes or modications to this system by other than
an authorized service facility could void authorization
to use this equipment.
PASS-Key III uses a radio frequency transponder in
the key that matches a decoder in your vehicle.
PASS-Key®III Electronic
Immobilizer Operation
The vehicle is equipped with PASS-Key®III
(Personalized Automotive Security System)
theft-deterrent system. PASS-Key
®III is a passive
theft-deterrent system.
The system is automatically armed when the
key is removed from the ignition.You do not have to manually arm or disarm the system.
The security light will come on if there is a problem
with arming or disarming the theft-deterrent system.
PASS-Key
®III uses a transponder in the ignition
key that matches a decoder in the vehicle.
When the PASS-Key
®III system senses that the wrong
key has been inserted into the ignition, it shuts down the
vehicle’s starter and fuel systems. The starter will not
work and fuel will stop owing to the engine. If someone
tries to start the vehicle again with the wrong key, the
vehicle will not start. Anyone using a trial-and-error
method to start the vehicle will be discouraged to do so
because of the high number of electrical key codes.
When trying to start the vehicle, if the engine does not
start and the STARTING DISABLED DUE TO THEFT
SYSTEM warning message on the Driver Information
Center (DIC) comes on, there may be a problem
with your theft-deterrent system. Turn the ignition off
and try again.
If the engine still does not start, and the key appears to
be undamaged, try another ignition key. At this time,
you may also want to check the fuse. SeeFuses and
Circuit Breakers on page 5-121. If the engine still does
not start with the other key, the vehicle needs service.
2-21

If the vehicle does start, the rst key may be faulty. See
your dealer/retailer who can service the PASS-Key®III
to have a new key made. In an emergency, contact
Roadside Assistance. SeeRoadside Assistance Program
on page 7-6for more information.
It is possible for the PASS-Key
®III decoder to accept
the transponder value of a new or replacement key.
Up to 10 keys may be programmed for the vehicle.
If all the programmed keys are lost or do not operate,
see your dealer/retailer or a locksmith who can service
PASS-Key
®III to have keys made and programmed
to the system.
Canadian Owners: If all the keys are lost or damaged,
only a dealer/retailer can service PASS-Key
®III to
have new keys made and programmed to the system.
The following procedure is for programming a new
or replacement key when you have at least one
already programmed key. To program the new key
do the following:
1. Verify that the new key has PK3 stamped on it.
2. Insert the master key in the ignition and start
the engine. If the engine will not start, see your
dealer/retailer for service.
3. After the engine has started, turn the key to
LOCK/OFF, and remove the key.4. Insert the key to be programmed and turn it to
ON/RUN within ve seconds of removing the
original key.
5. The STARTING DISABLED DUE TO THEFT
SYSTEM warning message on the DIC will turn off,
once the key has been programmed. It may not
be apparent that the SERVICE THEFT SYSTEM
warning message went on due to how quickly
the key is programmed.
6. Repeat Steps 1 through 5 if additional keys are to
be programmed.
If the STARTING DISABLED DUE TO THEFT SYSTEM
warning message appears and stays on the DIC while
the vehicle is being driven, the engine will be able to be
restarted if it is turned off. Your PASS-Key®III system,
however, is not working properly and must be serviced
by your dealer/retailer. The vehicle is not protected by
the PASS-Key
®III system at this time.
If the PASS-Key
®III key is lost or stolen, see your
dealer/retailer or a locksmith who can service
PASS-Key
®III to have a new key made.
Do not leave the key or device that disarms or
deactivates the theft deterrent system in the vehicle.
2-22

Starting and Operating
Your Vehicle
New Vehicle Break-In
Notice:Your vehicle does not need an elaborate
break-in. But it will perform better in the long run
if you follow these guidelines:
Do not drive at any one constant speed,
fast or slow, for the rst 500 miles (805 km).
Do not make full-throttle starts. Avoid
downshifting to brake or slow the vehicle.
Avoid making hard stops for the rst 200 miles
(322 km) or so. During this time the new brake
linings are not yet broken in. Hard stops
with new linings can mean premature wear and
earlier replacement. Follow this breaking-in
guideline every time you get new brake linings.
Do not tow a trailer during break-in. See
Towing a Trailer on page 4-29for the trailer
towing capabilities of your vehicle and more
information.
Following break-in, engine speed and load can
be gradually increased.
Ignition Positions
The ignition switch is located on the instrument panel,
to the right of the steering column.
There are four different
positions. Insert the
key in the ignition and
turn it to the right for
each position.
In order to shift out of PARK (P), ignition must be in the
ON/RUN and the regular brake pedal must be applied.
Notice:Using a tool to force the key from the
ignition switch could cause damage or break the key.
Use the correct key and turn the key only with your
hand. Make sure the key is all the way in. If none of
this works, then your vehicle needs service.
9(LOCK/OFF):This position locks the ignition,
steering wheel and transmission. It is a theft-deterrent
feature. This is the only position from which the key
can be removed.
2-23

If the steering wheel is locked, move it from right to
left and turn the key to ACC/ACCESSORY. If none
of this works, then your vehicle needs service.
ACC (ACC/ACCESSORY):This position allows things
like the radio and windshield wipers to operate while
the engine is off.
R(ON/RUN):This position is where the key returns
to after the vehicle is started. With the engine off,
the ON/RUN position displays some of the warning
and indicator lights.
The battery could be drained if you leave the key in the
ACC/ACCESSORY or ON/RUN position with the engine
off. You may not be able to start your vehicle if the battery
is allowed to drain for an extended period of time.
/(START):This position starts the engine. Let go
of the key when the engine starts. The key will return
to the ON/RUN for normal driving.
A continuous warning chime will sound and a KEY IN
IGNITION message will display on the Driver Information
Center (DIC) if the key is turned to LOCK/OFF or
ACC/ACCESSORY and the driver’s door is opened.
Key In the Ignition
Never leave your vehicle with the keys inside, as it
is an easy target for joy riders or thieves. If you
leave the key in the ignition and park your vehicle,
a chime will sound, when you open the driver’s door.
Always remember to remove your key from the ignition
and take it with you. This will lock your ignition and
transmission. Also, always remember to lock the doors.
The battery could be drained if you leave the key in
the ignition while your vehicle is parked. You may not
be able to start your vehicle after it has been parked
for an extended period of time.
Retained Accessory Power (RAP)
These vehicle accessories can be used for up to
10 minutes after the engine is turned off:
Audio System
Power Windows
Sunroof (if equipped)
Power to these features will continue to operate for
up to 10 minutes after the key is turned to LOCK/OFF
until a door is opened.
2-24

Starting the Engine
Move your shift lever to PARK (P) or NEUTRAL (N).
Your engine will not start in any other position – this is a
safety feature. To restart when you are already moving,
use NEUTRAL (N) only.
Notice:Do not try to shift to PARK (P) if your
vehicle is moving. If you do, you could damage the
transmission. Shift to PARK (P) only when your
vehicle is stopped.
Starting Procedure
1. With your foot off the accelerator pedal, turn the
ignition key to START. When the engine starts,
let go of the key. The idle speed will go down as
your engine gets warm. Do not race the engine
immediately after starting it. Operate the engine
and transmission gently to allow the oil to warm up
and lubricate all moving parts.Your vehicle has a Computer-Controlled Cranking
System. This feature assists in starting the engine
and protects components. If the ignition key is turned
to the START position, and then released when the
engine begins cranking, the engine will continue
cranking for a few seconds or until the vehicle
starts. If the engine does not start and the key is
held in START for many seconds, cranking will be
stopped after 15 seconds to prevent cranking motor
damage. To prevent gear damage, this system also
prevents cranking if the engine is already running.
Engine cranking can be stopped by turning the
ignition switch to the ACC/ACCESSORY or
LOCK/OFF position.
Notice:Cranking the engine for long periods of
time, by returning the key to the START position
immediately after cranking has ended, can overheat
and damage the cranking motor, and drain the
battery. Wait at least 15 seconds between each try,
to let the cranking motor cool down.
2-25

{CAUTION:
It is dangerous to get out of your vehicle if
the shift lever is not fully in PARK (P) with the
parking brake rmly set. Your vehicle can roll.
Do not leave your vehicle when the engine
is running unless you have to. If you have
left the engine running, the vehicle can move
suddenly. You or others could be injured.
To be sure your vehicle will not move, even
when you are on fairly level ground, always
set your parking brake and move the shift
lever to PARK (P). SeeShifting Into PARK (P)
on page 2-34. If you are pulling a trailer,
seeTowing a Trailer on page 4-29.Make sure the shift lever is fully in PARK (P) before
starting the engine. The vehicle has an automatic
transmission shift lock control system. You must fully
apply your regular brakes rst and then press the
shift lever button, located on the front of the shift lever,
before you can shift from PARK (P) when the ignition
key is in RUN. If the vehicle cannot be shifted out
of PARK (P), ease pressure on the shift lever by pushing
it all the way into PARK (P) as you maintain brake
application. Then press the shift lever button and move
the shift lever into another gear. SeeShifting Out of
PARK (P) on page 2-35.
REVERSE (R):Use this gear to back up.
Notice:Shifting to REVERSE (R) while your vehicle
is moving forward could damage the transmission.
The repairs would not be covered by your warranty.
Shift to REVERSE (R) only after your vehicle is
stopped.
To rock the vehicle back and forth to get out of snow,
ice or sand without damaging the transmission, see
If Your Vehicle is Stuck in Sand, Mud, Ice, or Snow
on page 4-21.
2-29

Parking Brake
The parking brake is
located to the left of the
brake pedal near the
driver’s door. To set the
parking brake, hold
the regular brake pedal
down with the right
foot. Push down on the
parking brake pedal,
with the left foot.
To release the parking brake, hold the regular brake
pedal down with the right foot and push the parking
brake pedal with the left foot. When the left foot is lifted,
the parking brake pedal will lift to the released position.
A warning chime will sound if the parking brake is
set, the ignition is on, and the shift lever is not in
PARK (P) or NEUTRAL (N).The brake light will also appear on the instrument panel
cluster when the parking brake is set. It will stay on if
the parking brake does not release fully.
The PARKING BRAKE ON message will also appear in
the Driver Information Center (DIC) when the parking
brake is set. SeeDIC Warnings and Messages on
page 3-67for more information.
Notice:Driving with the parking brake on can
overheat the brake system and cause premature
wear or damage to brake system parts. Make sure
that the parking brake is fully released and the brake
warning light is off before driving.
If the vehicle is towing a trailer and parked on a hill,
seeTowing a Trailer on page 4-29. That section shows
what to do rst to keep the trailer from moving.
2-33

Shifting Into PARK (P)
{CAUTION:
It can be dangerous to get out of your vehicle if
the shift lever is not fully in PARK (P) with the
parking brake rmly set. Your vehicle can roll.
If you have left the engine running, the vehicle
can move suddenly. You or others could be
injured. To be sure your vehicle will not move,
even when you are on fairly level ground, use
the steps that follow. If you are pulling a trailer,
seeTowing a Trailer on page 4-29.
1. Hold the brake pedal down with your right foot
and set the parking brake. SeeParking Brake
on page 2-33for more information.
2. Move the shift lever into PARK (P) by holding in
the button on the shift lever and pushing the shift
lever all the way toward the front of the vehicle.
3. Turn the ignition key to LOCK/OFF.
4. Remove the key and take it with you. If you can
leave your vehicle with the ignition key in your
hand, your vehicle is in PARK (P).
Leaving Your Vehicle With the
Engine Running
{CAUTION:
It can be dangerous to leave your vehicle with
the engine running. Your vehicle could move
suddenly if the shift lever is not fully in
PARK (P) with the parking brake rmly set. And,
if you leave the vehicle with the engine running,
it could overheat and even catch re. You or
others could be injured. Do not leave your
vehicle with the engine running.
If you have to leave your vehicle with the engine
running, be sure your vehicle is in PARK (P) and your
parking brake is rmly set before you leave it. After
you have moved the shift lever into PARK (P), hold
the regular brake pedal down. Then, see if you
can move the shift lever away from PARK (P) without
rst pushing the button.
If you can, it means that the shift lever was not fully
locked in PARK (P).
2-34