light PONTIAC SOLSTICE 2007 Owner's Manual

Your vehicle must have a working electrical system
(including adequate battery power) for the OnStar®
equipment to operate. There are other problems
OnStar®cannot control that may prevent OnStar®
from providing OnStar®service to you at any
particular time or place. Some examples are
damage to important parts of your vehicle in an
accident, hills, tall buildings, tunnels, weather or
wireless phone network congestion.
Your Responsibility
You may need to increase the volume of your
radio to hear the OnStar®advisor. If the light next
to the OnStar®buttons is red, this means that
your system is not functioning properly and should
be checked by a dealer. If the light appears
clear (no light is appearing), your OnStar
®
subscription has expired. You can always press
the OnStar®button to conrm that your OnStar®
equipment is active.
Storage Areas
Glove Box
To open the glove box, lift up on the lever. Use
the key to lock and unlock.
Cupholder(s)
There are two cupholders located in the center
console, press and release to extend forward.
98

Instrument Panel Overview........................ 108
Hazard Warning Flashers.......................... 110
Other Warning Devices............................. 110
Horn.......................................................... 110
Tilt Wheel.................................................. 111
Turn Signal/Multifunction Lever.................. 111
Turn and Lane-Change Signals................. 112
Headlamp High/Low-Beam Changer.......... 112
Flash-to-Pass............................................ 113
Windshield Wipers..................................... 113
Windshield Washer.................................... 114
Cruise Control........................................... 115
Headlamps................................................ 118
Headlamps on Reminder........................... 119
Daytime Running Lamps (DRL)................. 119
Fog Lamps................................................ 120
Instrument Panel Brightness...................... 120
Entry/Exit Lighting...................................... 120
Mirror Reading Lamps............................... 120
Battery Run-Down Protection..................... 121
Accessory Power Outlet(s)........................ 121
Ashtray(s) and Cigarette Lighter................ 122Climate Controls......................................... 122
Climate Control System............................. 122
Outlet Adjustment...................................... 126
Warning Lights, Gages, and Indicators..... 127
Instrument Panel Cluster........................... 128
Speedometer and Odometer...................... 129
Tachometer............................................... 129
Safety Belt Reminder Light........................ 130
Passenger Safety Belt Reminder Light....... 130
Airbag Readiness Light............................. 131
Passenger Airbag Status Indicator............. 132
Charging System Light.............................. 134
Brake System Warning Light..................... 134
Anti-Lock Brake System Warning Light...... 135
Electronic Stability Control (ESC)/
Traction Control System (TCS)
Indicator/Warning Light
(2.0L Engine Only).................................. 136
Engine Coolant Temperature
Warning Light........................................ 137
Low Coolant Warning Light....................... 138
Malfunction Indicator Lamp........................ 138
Section 3 Instrument Panel
105

Oil Pressure Light..................................... 142
Security Light............................................ 143
Reduced Engine Power Light
(2.4L Engine Only)................................. 143
Highbeam On Light................................... 143
Trunk Ajar Light........................................ 144
Service Vehicle Soon Light
(2.4L Engine Only)................................. 144
Fuel Gage................................................. 144
Low Fuel Warning Light............................ 145
Driver Information Center (DIC).................. 145
DIC Operation and Displays...................... 146
DIC Warnings and Messages.................... 148
DIC Vehicle Personalization....................... 152Audio System(s)......................................... 157
Setting the Time (Without Date Display).... 158
Setting the Time (With Date Display)......... 159
Radio with CD (Base)............................... 161
Radio with CD (MP3)................................ 166
Using an MP3........................................... 176
XM Radio Messages................................. 183
Theft-Deterrent Feature............................. 185
Audio Steering Wheel Controls.................. 185
Radio Reception........................................ 186
Care of Your CDs..................................... 187
Care of the CD Player.............................. 187
Fixed Mast Antenna.................................. 187
XM™ Satellite Radio Antenna System....... 187
Section 3 Instrument Panel
106

The main components of your instrument panel are the following:
A. Side Window Outlets. SeeClimate Control
System on page 122.
B. Air Outlets. SeeOutlet Adjustment on page 126.
C. Turn Signal/Multifunction Lever. SeeTurn
Signal/Multifunction Lever on page 111.
D. Cruise Control Buttons (If Equipped). See
Cruise Control on page 115.
E. Instrument Panel Cluster. SeeInstrument
Panel Cluster on page 128.
F. Audio Steering Wheel Controls (If Equipped).
SeeAudio Steering Wheel Controls on
page 185.
G. Instrument Panel Brightness Control. See
Instrument Panel Brightness on page 120.
H. Passenger Air Bag Status Indicator. See
Passenger Airbag Status Indicator on page 132.
I. Hazard Warning Flashers Button. SeeHazard
Warning Flashers on page 110.
J. Fog Lamp Button (If Equipped). SeeFog
Lamps on page 120.
K. Electronic Stability Control (ESC)/Traction
Control System (TCS) Button (If Equipped).
SeeElectronic Stability Control on page 200or
Traction Control System (TCS) on page 198.L. Driver Information Center (DIC) Controls (If
Equipped). SeeDriver Information Center (DIC)
on page 145.
M. Horn. SeeHorn on page 110.
N. Windshield Wiper/Washer Controls. See
Windshield Wipers on page 113andWindshield
Washer on page 114.
O. Climate Controls. SeeClimate Control System
on page 122.
P. Cigarette Lighter (If Equipped). Accessory
Power Outlet (If Equipped). SeeAshtray(s) and
Cigarette Lighter on page 122andAccessory
Power Outlet(s) on page 121.
Q. Shift Lever. SeeManual Transmission
Operation on page 85. SeeAutomatic
Transmission Operation on page 82
(if equipped with automatic transmission).
R. Parking Brake Lever. SeeParking Brake on
page 86.
S. Audio System. SeeAudio System(s) on
page 157.
T. Cupholder. SeeCupholder(s) on page 98.
U. Trunk Release. SeeTrunk on page 68.
V. Glove Box. SeeGlove Box on page 98.
109

Turn and Lane-Change Signals
The turn signal has two upward (for right) and
two downward (for left) positions. These positions
allow you to signal a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When the turn is nished, the lever will
return automatically.
An arrow on the
instrument panel cluster
will ash in the
direction of the turn or
lane change.
To signal a lane change, raise or lower the lever
until the arrow starts to ash. Hold it there until you
complete your lane change. The lever will return
by itself when you release it.As you signal a turn or a lane change, if the
arrows ash rapidly, a signal bulb may be burned
out and other drivers will not see your turn
signal. If a bulb is burned out, replace it to help
avoid an accident.
If the arrows do not go on at all when you signal a
turn, check the fuse. SeeFuses and Circuit
Breakers on page 326.
Headlamp High/Low-Beam Changer
To change the headlamps from low beam to high
beam, push the turn signal lever away from you.
When the high beams
are on, this light on the
instrument panel
cluster will also be on.
To change the headlamps from high beam to low
beam, pull the turn signal lever toward you.
112

RES+ (Resume):Press this button to resume a
set speed and to accelerate the speed.
SET−(Set):Press this button to set a speed and
to decrease the speed.
To set a speed do the following:
1. Press the on/off button to turn cruise control on.
The indicator light on the button will come on.
2. Get to the speed you want.
3. Press the SET−control button and release it.
The CRUISE ENGAGED message will appear
on the Driver Information Center (DIC) to
show the system is engaged.
4. Take your foot off the accelerator pedal.
When you apply the brakes or depress the clutch,
the cruise control will shut off.Resuming a Set Speed
Suppose you set your cruise control at a desired
speed and then you apply the brake. This
disengages the cruise control. To return to your
previously set speed, you do not need to go
through the set process again. Once you are going
about 25 mph (40 km/h) or more, you can press
the RES+ button briey.
This will take you back up to your previously
chosen speed and stay there.
Increasing Speed While Using
Cruise Control
There are two ways to increase speed.
1. Disengage the cruise control by applying the
brake pedal but do not turn it off. Accelerate
to a higher speed and reset the cruise control.
2. If the cruise control system is already
engaged, press the RES+ button. Press it until
you get up to the speed you want, and then
release the button. To increase your speed in
very small amounts, press the RES+ button
briey and then release it. Each time you
do this, your vehicle will go about 1 mph
(1.6 km/h) faster.
116

Reducing Speed While Using
Cruise Control
If the cruise control system is already engaged,
Push and hold the SET−part of the button
until you reach the lower speed desired,
then release it.
To slow down in very small amounts, push the
SET−part of the button briey. Each time this
is done, your vehicle will go about 1 mph
(1.6 km/h) slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase your speed.
When you take your foot off the pedal, your
vehicle will slow down to the cruise control speed
you set earlier.
Using Cruise Control on Hills
How well your cruise control will work on hills
depends upon the vehicle speed, load, and the
steepness of the hills. When going up steep hills,
you might have to step on the accelerator pedal
to maintain the vehicle speed. When going
downhill, you might have to brake or shift to a
lower gear to keep the vehicle speed down.
Of course, applying the brake turns off the cruise
control. Many drivers nd this to be too much
trouble and do not use cruise control on steep hills.
Ending Cruise Control
To end cruise control, step lightly on the brake
pedal or the clutch pedal if your vehicle has
a manual transmission.
Stepping on the brake pedal or clutch pedal will
only end the current cruise control session. Press
the cruise control on/off button to turn the
system completely off.
Erasing Speed Memory
When you turn off the cruise control or the
ignition, the cruise control set speed memory is
erased.
117

Headlamps
The lever on the left side of the steering column
operates the exterior lamps.
The exterior lamp switch has the following
four positions:
2(Headlamps):This position turns on the
headlamps, parking lamps, and taillamps.
;(Parking Lamps):This position turns on the
parking lamps and taillamps only.
AUTO (Automatic Headlamp System):This
position automatically turns on the Daytime
Running Lamps (DRL) during daytime, and the
headlamps, parking lamps, and taillamps at night.
P(Off/On):This position is an Off/On switch for
the Automatic Headlamp System. In Canada, this
applies to vehicles with an automatic transmission
set to PARK (P) and manual transmission vehicles
with the parking brake engaged.
When operating in AUTO, a brief turn of the
switch to off/on will turn off the Automatic
Headlamp System. An AUTO LIGHTS OFF
message will display on the Driver Information
Center (DIC), if the vehicle has one, and a chime
will sound. Turning the switch to off/on again
will turn the Automatic Headlamp System back on.
An AUTO LIGHTS ON message will display on
the Driver Information Center (DIC).
The Automatic Headlamp System is always turned
on at the beginning of an ignition cycle for vehicles
with manual transmission. When the parking brake
is engaged, the automatic headlamps will turn off.
For vehicles with an automatic transmission, when
the shift lever is shifted out of PARK (P), the
Automatic Headlamp System will turn on. Shifting
the lever back to PARK (P) will turn off the
automatic headlamp system for vehicles with an
automatic transmission.
118

Headlamps on Reminder
If you open the driver’s door with the ignition off
and the lamps on, you will hear a warning chime.
Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier
for others to see the front of your vehicle during
the day. DRL can be helpful in many different
driving conditions, but they can be especially
helpful in the short periods after dawn and before
sunset. Fully functional daytime running lamps
are required on all vehicles rst sold in Canada.
Your vehicle has a light sensor on top of the
instrument panel that helps control the DRL. Make
sure it is not covered or the headlamps will
come on when they are not needed.The DRL system makes both low beam headlamps
turn on at reduced intensity when the following
conditions are met:
The ignition is on.
The exterior lamp control is turned to AUTO.
The light sensor detects daytime light.
The shift lever is not in PARK (P).
While the DRL system is on, the taillamps,
sidemarker lamps, and instrument panel lights will
not be on.
The DRL system turns off on U.S. vehicles by
using the on/off switch for one ignition cycle, if the
vehicle is in the PARK (P) position, or if the
vehicle speed is less than 5 mph (8 km h) after
the vehicle is started.
For vehicles rst sold in Canada the DRL system
will turn off when a automatic transmission
vehicle is in the PARK (P) position or the park
brake is set on a manual transmission vehicle and
the vehicle speed is less than 8 mph (13 km h).
As with any vehicle, you should turn on the regular
headlamp system when it is needed.
119

Fog Lamps
If your vehicle has a fog
lamp button, it is located
on the instrument
panel, to the right of the
steering wheel.
The ignition must be on to turn your fog lamps on.
Push the button to turn the fog lamps on.
An indicator light on the fog lamp button will come
on when the fog lamps are on. Push the button
again to turn the fog lamps off.
The parking lamps will automatically turn on and
off when the fog lamps are turned on and off.
The fog lamps will turn off while the high-beam
headlamps are turned on.
Some localities have laws that require the
headlamps to be on along with the fog lamps.
Instrument Panel Brightness
DInstrument Panel Brightness:The control
for this feature is located on the instrument
panel to the right of the steering wheel.
Turn the knob clockwise to brighten the lights or
counterclockwise to dim them.
Entry/Exit Lighting
The lamps inside your vehicle will go on when you
open any door. These lamps will fade out after
about 20 seconds after all of the doors have been
closed or when the ignition is turned on. These
lamps will also go on when you press the
trunk release, unlock symbol button or the horn
symbol on the keyless entry system transmitter.
The lamps inside your vehicle will stay on for about
20 seconds after your key is removed from the
ignition to provide an illuminated exit.
Mirror Reading Lamps
Your vehicle has reading lamps on the rearview
mirror. Push the button to turn the reading
lamps on and off.
120