trunk PONTIAC SOLSTICE 2008 Owner's Manual
[x] Cancel search | Manufacturer: PONTIAC, Model Year: 2008, Model line: SOLSTICE, Model: PONTIAC SOLSTICE 2008Pages: 348, PDF Size: 5.23 MB
Page 244 of 348

Taillamps, Turn Signal, and
Stoplamps
To replace one of these bulbs:
1. Open the trunk. SeeTrunk on page 2-9for more
information.
2. Remove the two screws, which hold the taillamp
assembly, from inside the vehicle.
3. Remove the taillamp assembly.
4. Turn the bulb socket counterclockwise to remove.
5. Pull the bulb from the socket.
6. Install a new bulb.
7. Reverse the steps to reinstall the taillamp assembly.
Back-Up Lamps
The back-up lamps are
located in the rear bumper.
To replace a bulb:
1. Reach behind, up and under the rear bumper and
locate the bulb socket.
2. Turn it counterclockwise to remove from the bulb
assembly.
3. Pull the bulb from the bulb socket.
4. Push in a new bulb into the bulb socket.
5. Reinstall the bulb socket by lining up the tabs in the
lamp assembly and turn it clockwise to secure it.
5-48
Page 273 of 348

Accessing the Tire Sealant and
Compressor Kit
To access the tire sealant and compressor kit:
1. Make sure the convertible top is in the up position
before accessing the tire sealant and compressor kit.
2. Open the trunk. SeeTrunk on page 2-9for more
information.
3. Locate the tire sealant and compressor kit on the
driver side of the vehicle, near the back corner of
the trunk.4. Remove the tire sealant
and compressor kit
strap by squeezing the
two tabs of the quick
release buckle.
5. Remove the sealant and compressor kit from its
foam container.
Tire Sealant
Read and follow the safe handling instructions on the
sealant canister.
The sealant can temporarily seal a punctures up to
1/4 inch (6 mm) in the tread area of the tire. The sealant
cannot seal sidewall damage, large punctures, or a
tire that has unseated from the wheel. SeeRoadside
Assistance Program on page 7-7if you need assistance.
The sealant can only be used to seal one tire.
After usage, the sealant canister and sealant lling
hose assembly must be replaced at a dealer/retailer.
See Removal and Installation of Sealant Canister later
in this section.
5-77
Page 277 of 348

{CAUTION:
Storing the tire sealant and compressor
kit or other equipment in the passenger
compartment of the vehicle could cause injury.
In a sudden stop or collision, loose equipment
could strike someone. Store the tire sealant
and compressor kit in the proper place.
16. Return the equipment to the proper storage location
in the trunk of your vehicle. You may need to
loosen the retention strap to wrap it around the
sealant and compressor kit and foam container.
To do this, pull apart the strap and loosen the strap
at the quick release buckle. Then snap the buckle
together, pull the strap tight, and secure the
loose end of the strap by mating the ends.
17. Immediately drive the vehicle 5 miles (8 km) to
distribute the sealant evenly in the tire.18. Stop at a safe location and check the tire pressure,
refer to Steps 1 through 8 under “Using the Air
Compressor without Sealant” next in this section.
If the tire pressure has not dropped more than
10 psi (68 kPa) from the recommended in ation
pressure, you can in ate the tire back up to
the recommended in ation pressure.
19. If the tire pressure has fallen more then
10 psi (68 kPa), below the recommended in ation
pressure, stop driving the vehicle. The tire is
too damaged for the sealant to work. See
Roadside Assistance Program on page 7-7.
20. Wipe off any sealant from the wheel, tire, and
vehicle with a rag.
21. Dispose of the sealant canister at a local
dealer/retailer or in accordance with local state
codes and practices.
After using the sealant canister, replace it with a
new canister from your dealer/retailer.
22. After temporarily sealing a tire with the tire sealant
and compressor kit, take your vehicle to your
dealer/retailer to have the tire inspected and
repaired.
5-81