brake light PONTIAC SOLSTICE 2009 Owners Manual

Vehicle Symbols
The vehicle has components and labels that use
symbols instead of text. Symbols are shown along with
the text describing the operation or information
relating to a specic component, control, message,
gage, or indicator.
M:This symbol is shown when you need to see your
owner manual for additional instructions or information.
*:This symbol is shown when you need to see a
service manual for additional instructions or information.
Vehicle Symbol Chart
Here are some additional symbols that may be found on
the vehicle and what they mean. For more information
on the symbol, refer to the index.
9:Airbag Readiness Light
#:Air Conditioning
!:Antilock Brake System (ABS)
g:Audio Steering Wheel Controls or OnStar®
$:Brake System Warning Light
":Charging System
I:Cruise Control
B:Engine Coolant Temperature
O:Exterior Lamps
#:Fog Lamps
.:Fuel Gage
+:Fuses
i:Headlamp High/Low-Beam Changer
j:LATCH System Child Restraints
*:Malfunction Indicator Lamp
::Oil Pressure
}:Power
/:Remote Vehicle Start
>:Safety Belt Reminders
7:Tire Pressure Monitor
F:Traction Control
M:Windshield Washer Fluid
iv

Remote Trunk Release
To open the trunk from
inside the vehicle, press
the remote trunk release
button located in the
glovebox.
The remote trunk release will only work when either the
ignition is off or in ACC/ACCESSORY, the parking
brake is engaged, or the vehicle speed is less than
2 mph (3 km/h).
Emergency Trunk Release Handle
Notice:Do not use the emergency trunk release
handle as a tie-down or anchor point when securing
items in the trunk as it could damage the handle.
The emergency trunk release handle is only
intended to aid a person trapped in a latched trunk,
enabling them to open the trunk from the inside.
There is a glow-in-the-dark emergency trunk release
handle located inside the trunk on the driver’s side. This
handle will glow following exposure to light. If someone
is locked in the trunk, they can pull the release
handle and push the trunk lid open from the inside to
open the trunk.
2-9

Notice:Shifting out of P (Park) or N (Neutral) with
the engine running at high speed may damage
the transmission. The repairs would not be covered
by the vehicle warranty. Be sure the engine is
not running at high speed when shifting the vehicle.
D (Drive):This position is for normal driving with the
automatic transmission. It provides the best fuel
economy. If you need more power for passing and
you are:
Going less than about 35 mph (55 km/h), push the
accelerator pedal about halfway down.
Going about 35 mph (55 km/h), push the accelerator
all the way down.
The transmission will shift down to a lower gear and
have more power.
Downshifting the transmission in slippery road conditions
could result in skidding, see “Skidding” underLoss of
Control on page 4-12.
4 (Fourth):This position is also used for normal
driving. However, it reduces vehicle speed more than
D (Drive) without using the brakes. You might choose
4 (Fourth) instead of D (Drive) when driving on hilly,
winding roads and when going down a steep hill.I (Intermediate):This position is also used for normal
driving. However, it reduces vehicle speed without using
the brakes, for slight downgrades where the vehicle
would otherwise accelerate due to steepness of grade.
If constant upshifting or downshifting occurs while
driving on steep hills, this position can be used to
prevent repetitive types of shifts. You might choose
I (Intermediate) instead of D (Drive) when driving on hilly
and winding roads.
L (Low):This position reduces vehicle speed more
than I (Intermediate) without using the brakes. You can
use it on very steep hills, or in deep snow or mud. If
the shift lever is put in L (Low), the transmission will not
shift into a low gear until the vehicle is going slowly
enough.
Notice:Spinning the tires or holding the vehicle in
one place on a hill using only the accelerator
pedal may damage the transmission. The repair will
not be covered by the vehicle warranty. If you
are stuck, do not spin the tires. When stopping on a
hill, use the brakes to hold the vehicle in place.
2-21

Parking Brake
The parking brake lever is located between the
front seats.
To set the parking brake, hold the brake pedal down
and pull up on the parking brake lever. If the ignition is
on, the brake system warning light will come on.
SeeBrake System Warning Light on page 3-25.To release the parking brake, hold the brake pedal
down. Pull the parking brake lever up until you can press
the release button. Hold the release button in as you
move the brake lever all the way down.
If you forget to release your parking brake, a chime will
sound and a warning message will be displayed in
the Driver Information Center (DIC) when the vehicle is
moving faster than 5 mph (8 kph). SeeDIC Warnings
and Messages on page 3-37.
Notice:Driving with the parking brake on can
overheat the brake system and cause premature
wear or damage to brake system parts. Make sure
that the parking brake is fully released and the brake
warning light is off before driving.
2-23

Instrument Panel Overview...............................3-4
Hazard Warning Flashers................................3-5
Horn .............................................................3-5
Tilt Wheel.....................................................3-6
Turn Signal/Multifunction Lever.........................3-6
Turn and Lane-Change Signals........................3-7
Headlamp High/Low-Beam Changer..................3-7
Flash-to-Pass.................................................3-7
Windshield Wipers..........................................3-8
Windshield Washer.........................................3-9
Cruise Control................................................3-9
Headlamps..................................................3-12
Headlamps on Reminder................................3-13
Daytime Running Lamps (DRL).......................3-13
Fog Lamps ..................................................3-13
Instrument Panel Brightness...........................3-14
Entry/Exit Lighting.........................................3-14
Mirror Reading Lamps...................................3-14
Battery Run-Down Protection..........................3-14
Accessory Power Outlet(s).............................3-14
Ashtray(s) and Cigarette Lighter......................3-15
Climate Controls............................................3-16
Climate Control System.................................3-16
Outlet Adjustment.........................................3-19Warning Lights, Gages, and Indicators............3-19
Instrument Panel Cluster................................3-20
Speedometer and Odometer...........................3-21
Tachometer.................................................3-21
Safety Belt Reminders...................................3-22
Airbag Readiness Light..................................3-23
Passenger Airbag Status Indicator...................3-24
Charging System Light..................................3-25
Brake System Warning Light..........................3-25
Antilock Brake System (ABS) Warning Light.....3-26
Electronic Stability Control (ESC)/Traction
Control System (TCS) Indicator/Warning
Light........................................................3-27
Engine Coolant Temperature Warning Light......3-28
Low Coolant Warning Light............................3-28
Tire Pressure Light.......................................3-29
Malfunction Indicator Lamp.............................3-29
Oil Pressure Light.........................................3-32
Security Light...............................................3-32
Highbeam On Light.......................................3-33
Trunk Ajar Light............................................3-33
Fuel Gage...................................................3-33
Low Fuel Warning Light.................................3-34
Section 3 Instrument Panel
3-1

The main components of the instrument panel are the
following:
A. Side Window Outlets. SeeClimate Control System
on page 3-16.
B.Outlet Adjustment on page 3-19.
C.Turn Signal/Multifunction Lever on page 3-6.
D.Cruise Control on page 3-9(If Equipped).
E.Instrument Panel Cluster on page 3-20.
F.Audio Steering Wheel Controls on page 3-79
(If Equipped).
G.Instrument Panel Brightness on page 3-14.
H.Passenger Airbag Status Indicator on page 3-24.
I.Hazard Warning Flashers on page 3-5.
J.Fog Lamps on page 3-13(If Equipped).
K. Electronic Stability Control (ESC)/Traction Control
System (TCS) Button (If Equipped). SeeElectronic
Stability Control (ESC) on page 4-6orTraction
Control System (TCS) on page 4-8.
L.Driver Information Center (DIC) on page 3-34.
M.Horn on page 3-5.
N.Windshield Wipers on page 3-8andWindshield
Washer on page 3-9.
O.Climate Control System on page 3-16.P. Cigarette Lighter (If Equipped).Ashtray(s) and
Cigarette Lighter on page 3-15andAccessory Power
Outlet(s) on page 3-14(If Equipped).
Q. Shift Lever. SeeManual Transmission Operation on
page 2-22. SeeAutomatic Transmission Operation
on page 2-19(If equipped with automatic
transmission).
R.Parking Brake on page 2-23.
S.Audio System(s) on page 3-46.
T.Cupholders on page 2-33.
U. Trunk Release. SeeTrunk on page 2-8.
V.Glove Box on page 2-33.
Hazard Warning Flashers
|(Hazard Warning Flasher):Press this button
located on the instrument panel, to make the front and
rear turn signal lamps ash on and off. This warns
others that you are having trouble.
Press
|again to turn the ashers off.
Horn
To sound the horn, press the center pad on the steering
wheel.
3-5

Setting Cruise Control
{CAUTION:
If you leave your cruise control on when you are
not using cruise, you might hit a button and go
into cruise when you do not want to. You could be
startled and even lose control. Keep the cruise
control switch off until you want to use cruise
control.
The cruise control buttons
are located on the left side
of the steering wheel.
J(On/Off):Press to turn the cruise control system on
and off.RES+ (Resume):Press to resume a set speed and to
accelerate the speed.
SET−(Set):Press to set a speed and to decrease the
speed.
To set a speed do the following:
1. Press
Ito turn cruise control on. The indicator
light on the button will come on.
2. Get to the desired speed.
3. Press the SET−control button and release it. The
CRUISE ENGAGED message will appear on the
Driver Information Center (DIC) to show the system
is engaged.
4. Take your foot off the accelerator pedal.
When you apply the brakes or depress the clutch, the
cruise control will shut off.
Resuming a Set Speed
If the cruise control is at a desired speed and then the
brake is applied, this disengages the cruise control.
But it does not need to be reset. Once the vehicle
is going about 25 mph (40 km/h) or more, press the
RES+ button briey.
This takes you back up to the previously chosen speed
and stays there.
3-10

Increasing Speed While Using Cruise
Control
There are two ways to increase speed.
1. Disengage the cruise control by applying the brake
pedal but do not turn it off. Accelerate to a higher
speed and reset the cruise control.
2. If the cruise control system is already engaged,
press the RES+ button. Press it until the desired
speed is reached, and then release the button.
To increase the vehicle speed in small amounts,
press the RES+ button briey and then release
it. Each time this is done, the vehicle goes about
1 mph (1.6 km/h) faster.
Reducing Speed While Using Cruise
Control
If the cruise control system is already engaged,
Push and hold the SET−part of the button until the
lower speed desired is reached, then release it.
To slow down in small amounts, push the SET−
part of the button briey. Each time this is done,
the vehicle goes about 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using
Cruise Control
Use the accelerator pedal to increase the vehicle’s
speed. When you take your foot off the pedal, the
vehicle will slow down to the cruise control speed
set earlier.
Using Cruise Control on Hills
How well the cruise control works on hills depends upon
the vehicle speed, load, and the steepness of the
hills. When going up steep hills, you might have to step
on the accelerator pedal to maintain the vehicle
speed. When going downhill, you might have to brake
or shift to a lower gear to keep the vehicle speed down.
When the brakes are applied the cruise control will
turn off.
Ending Cruise Control
To end cruise control, step lightly on the brake
pedal or the clutch pedal if the vehicle has a manual
transmission.
Stepping on the brake pedal or clutch pedal will only
end the current cruise control session.
Press
Ito turn the system completely off.
3-11

Erasing Speed Memory
The cruise control set speed memory is erased when
the cruise control or the ignition is turned off.
Headlamps
The lever on the left side of the steering column
operates the exterior lamps.
The exterior lamp switch has the following four positions:
2(Headlamps):Turns on the headlamps, parking
lamps, and taillamps.
;(Parking Lamps):Turns on the parking lamps and
taillamps only.AUTO (Automatic Headlamp System):Automatically
turns on the Daytime Running Lamps (DRL) during
daytime, and the headlamps, parking lamps, and
taillamps at night.
P(Off/On):Turns the Automatic Headlamp System
on or off. In Canada, this applies to vehicles with
an automatic transmission set to P (Park) and manual
transmission vehicles with the parking brake engaged.
When operating in AUTO, a brief turn of the switch
to off/on will turn off the Automatic Headlamp System.
An AUTO LIGHTS OFF message displays on the Driver
Information Center (DIC) and a chime will sound.
Turning the switch to off/on again will turn the Automatic
Headlamp System back on. An AUTO LIGHTS ON
message will display on the Driver Information
Center (DIC).
The Automatic Headlamp System is always turned on at
the beginning of an ignition cycle for vehicles with
manual transmission. When the parking brake is
engaged, the automatic headlamps will turn off.
For vehicles with an automatic transmission, when the
shift lever is shifted out of P (Park), the Automatic
Headlamp System turns on. Shifting the lever back to
P (Park) will turn off the automatic headlamp system.
3-12

Headlamps on Reminder
If the drivers door is opened with the ignition off and the
lamps on, a warning chime will sound. This indicates
that the headlamps are still on.
Daytime Running Lamps (DRL)
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the
day. Fully functional daytime running lamps are required
on all vehicles rst sold in Canada.
The vehicle has a light sensor on top of the instrument
panel that helps control the DRL. Do not cover this
sensor or the headlamps will come on when they are
not needed.
The DRL system makes both low beam headlamps turn
on at reduced intensity when the following conditions
are met:
The ignition is on.
The exterior lamp control is turned to AUTO.
The light sensor detects daytime light.
The shift lever is not in P (Park).
While the DRL system is on, the taillamps, sidemarker
lamps, and instrument panel lights will not be on.The DRL system turns off on U.S. vehicles by using the
on/off switch for one ignition cycle, if the vehicle is in
the P (Park) position, or if the vehicle speed is less than
5 mph (8 km/h) after the vehicle is started.
For vehicles rst sold in Canada the DRL system will
turn off when a automatic transmission vehicle is in the
P (Park) position or the park brake is set on a manual
transmission vehicle and the vehicle speed is less than
8 mph (13 km/h).
The regular headlamp system should be turned on
when it is needed.
Fog Lamps
For vehicles with fog lamps, the button is located on the
instrument panel, to the right of the steering wheel.
The ignition must be on to use the fog lamps.
#:Press to turn the fog lamps on and off. An indicator
light on the button comes on when the fog lamps
are on.
The parking lamps automatically turn on and off when
the fog lamps are turned on and off.
The fog lamps will turn off while the high-beam
headlamps are turned on.
Some localities have laws that require the headlamps to
be on along with the fog lamps.
3-13