service PONTIAC VIBE 2006 Repair Manual

55,000 Miles (88 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control Service.
❑Rotate tires. SeeTire Inspection and Rotation
on page 5-62for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving in
dusty conditions. Replace lter if necessary.
60,000 Miles (96 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control Service.
❑Rotate tires. SeeTire Inspection and Rotation
on page 5-62for proper rotation pattern and
additional information.(See footnote +.)
❑Replace engine air cleaner lter (or every 24 months,
whichever occurs rst). SeeEngine Air Cleaner/Filter
on page 5-20for more information.
❑Replace passenger compartment air lter.
❑
Inspect engine accessory drive belts (or every
48 months, whichever occurs rst). Visually inspect
belt for fraying, excessive cracks, or obvious damage.
Replace belt if necessary.An Emission Control Service.
❑Inspect for tappet noise and engine vibration. Adjust
valve clearance to factory specications if necessary
(or every 48 months, whichever occurs rst).
An Emission Control Service.❑Inspect fuel tank, cap, cap gasket, and lines for
damage or leaks (or every 24 months, whichever
occurs rst). Replace parts as needed.An Emission
Control Service. (See footnote †.)
❑Change transfer case uid when doing frequent
trailer towing.
❑Change rear differential uid when doing frequent
trailer towing.
❑Change manual transaxle uid every 30,000 miles
(48 000 km) only if your vehicle is used to tow a
trailer.
❑Change automatic transaxle uid every 60,000 miles
(96 000 km) if the vehicle is mainly driven under one
or more of these conditions:
In heavy city traffic where the outside
temperature regularly reaches 90°F (32°C)
or higher.
In hilly or mountainous terrain.
When doing frequent trailer towing.
Uses such as found in taxi, police, or delivery
service.
If you do not use your vehicle under any of these
conditions, the uid does not require changing.
See Part D: Recommended Fluids and Lubricants on
page 6-19for the proper uid to use.
6-8

65,000 Miles 104 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control Service.
❑Rotate tires. SeeTire Inspection and Rotation
on page 5-62for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving in
dusty conditions. Replace lter if necessary.
70,000 Miles (112 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control Service.
❑Rotate tires. SeeTire Inspection and Rotation
on page 5-62for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving in
dusty conditions. Replace lter if necessary.
75,000 Miles (120 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control Service.
❑Rotate tires. SeeTire Inspection and Rotation
on page 5-62for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving in
dusty conditions. Replace lter if necessary.❑Inspect passenger compartment air lter.
❑Inspect engine accessory drive belts (or 12 months
since last inspection).An Emission Control Service.
❑Change transfer case uid when doing frequent trailer
towing.
❑Change rear differential uid when doing frequent
trailer towing.
80,000 Miles (128 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control Service.
❑Rotate tires. SeeTire Inspection and Rotation
on page 5-62for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving in
dusty conditions. Replace lter if necessary.
85,000 Miles (136 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control Service.
❑Rotate tires. SeeTire Inspection and Rotation
on page 5-62for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving in
dusty conditions. Replace lter if necessary.
6-9

90,000 Miles (144 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control Service.
❑Rotate tires. SeeTire Inspection and Rotation
on page 5-62for proper rotation pattern and
additional information.(See footnote +.)
❑Replace engine air cleaner lter (or every 24 months,
whichever occurs rst). SeeEngine Air Cleaner/Filter
on page 5-20for more information.
❑Replace passenger compartment air lter.
❑Inspect engine accessory drive belts (or 12 months
since last inspection).An Emission Control Service.
❑Inspect fuel tank, cap, cap gasket and lines for
damage or leaks (or every 24 months, whichever
occurs rst). Replace parts as needed.An Emission
Control Service. (See footnote †.)
❑Change manual transaxle uid every 30,000 miles
(48 000 km) only if your vehicle is used to tow
a trailer.
❑Change transfer case uid when doing frequent
trailer towing.
❑Change rear differential uid when doing frequent
trailer towing.
95,000 Miles (152 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control Service.
❑Rotate tires. SeeTire Inspection and Rotation
on page 5-62for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving in
dusty conditions. Replace lter if necessary.
100,000 Miles (160 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control Service.
❑Rotate tires. SeeTire Inspection and Rotation
on page 5-62for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving in
dusty conditions. Replace lter if necessary.
❑Drain, ush, and rell the cooling system (or every
5 years, whichever occurs rst). This service can
be complex; you should have your dealer perform this
service. SeeEngine Coolant on page 5-26for what
to use. Inspect hoses. Clean radiator, condenser,
pressure cap, and neck. Pressure test cooling system
and pressure cap.An Emission Control Service.
6-10

105,000 Miles (168 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control Service.
❑Rotate tires. SeeTire Inspection and Rotation
on page 5-62for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving in
dusty conditions. Replace lter if necessary.
❑Inspect passenger compartment air lter.
❑Inspect engine accessory drive belts (or every
48 months, whichever occurs rst). Visually inspect
belt for fraying, excessive cracks, or obvious damage.
Replace belt if necessary.An Emission Control
Service.
❑Change transfer case uid when doing frequent
trailer towing.
❑Change rear differential uid when doing frequent
trailer towing.
110,000 Miles (176 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control Service.
❑Rotate tires. SeeTire Inspection and Rotation
on page 5-62for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving in
dusty conditions. Replace lter if necessary.
115,000 Miles (184 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control Service.
❑Rotate tires. SeeTire Inspection and Rotation
on page 5-62for proper rotation pattern and
additional information.(See footnote +.)
❑Inspect engine air cleaner lter if you are driving in
dusty conditions. Replace lter if necessary.
6-11

120,000 Miles (192 000 km)
❑Change engine oil and lter (or every 3 months,
whichever occurs rst).An Emission Control Service.
❑Rotate tires. SeeTire Inspection and Rotation
on page 5-62for proper rotation pattern and
additional information.(See footnote +.)
❑Replace engine air cleaner lter (or every 24 months,
whichever occurs rst). SeeEngine Air Cleaner/Filter
on page 5-20for more information.
❑Replace passenger compartment air lter.
❑
Inspect engine accessory drive belts (or every
48 months, whichever occurs rst). Visually inspect
belt for fraying, excessive cracks, or obvious damage.
Replace belt if necessary.An Emission Control Service.
❑Replace spark plugs.An Emission Control Service.
❑Inspect for tappet noise and engine vibration.
Adjust valve clearance to factory specications
if necessary (or every 48 months, whichever occurs
rst).An Emission Control Service.
❑Inspect fuel tank, cap, cap gasket, and lines for
damage or leaks (or every 24 months, whichever
occurs rst). Replace parts as needed.An Emission
Control Service. (See footnote †.)❑Change transfer case uid when doing frequent
trailer towing.
❑Change rear differential uid when doing frequent
trailer towing.
❑Change manual transaxle uid every 30,000 miles
(48 000 km) only if your vehicle is used to tow a
trailer.
❑Change automatic transaxle uid every 60,000 miles
(96 000 km) if the vehicle is mainly driven under one
or more of these conditions:
In heavy city traffic where the outside
temperature regularly reaches 90°F (32°C)
or higher.
In hilly or mountainous terrain.
When doing frequent trailer towing.
Uses such as found in taxi, police, or delivery
service.
If you do not use your vehicle under any of these
conditions, the uid does not require changing.
See Part D: Recommended Fluids and Lubricants
on page 6-19for the proper uid to use.
6-12

Part B: Owner Checks and Services
Listed in this part are owner checks and services
which should be performed at the intervals specied to
help ensure the safety, dependability and emission
control performance of your vehicle.
Be sure any necessary repairs are completed at once.
Whenever any uids or lubricants are added to your
vehicle, make sure they are the proper ones, as shown
in Part D.
At Each Fuel Fill
It is important for you or a service station attendant to
perform these underhood checks at each fuel ll.
Engine Oil Level Check
Check the engine oil level and add the proper oil if
necessary. SeeEngine Oil on page 5-16for further
details.
Engine Coolant Level Check
Check the engine coolant level and add the proper
coolant mixture if necessary. SeeEngine Coolant on
page 5-26for further details.
Windshield Washer Fluid Level Check
Check the windshield washer uid level in the windshield
washer uid reservoir and add the proper uid if
necessary. SeeWindshield Washer Fluid on page 5-36
for further details.
Hood Latch Operation Check
Pull the primary hood latch release handle inside the
vehicle. The secondary latch should keep the hood from
opening all the way when the primary latch is released.
Make sure the hood closes rmly. SeeHood Release
on page 5-11for further details.
At Least Once a Month
Tire Ination Check
Visually inspect your tires and make sure tires are
inated to the correct pressures. Do not forget to
check your spare tire. SeeTires on page 5-52for
further details.
6-13

At Least Twice a Year
Restraint System Check
Make sure the safety belt reminder light and all your
belts, buckles, latch plates, retractors and anchorages
are working properly. Look for any other loose or
damaged safety belt system parts. If you see anything
that might keep a safety belt system from doing its
job, have it repaired. Have any torn or frayed safety belts
replaced.
Also look for any opened or broken airbag coverings,
and have them repaired or replaced. (The airbag system
does not need regular maintenance.)
Wiper Blade Check
Inspect wiper blades for wear or cracking. Replace blade
inserts that appear worn or damaged or that streak or
miss areas of the windshield. Also seeWindshield,
Backglass, and Wiper Blades on page 5-86.
Weatherstrip Lubrication
Silicone grease on weatherstrips will make them last
longer, seal better, and not stick or squeak. Apply
silicone grease with a clean cloth. During very cold,
damp weather more frequent application may be
required. SeePart D: Recommended Fluids and
Lubricants on page 6-19.
Fluid Level Check
Check the power steering pump, rear axle, transfer
case, and automatic or manual transaxle uid levels and
add as needed. SeePower Steering Fluid on page 5-35
andAutomatic Transaxle Fluid on page 5-21or
Manual Transaxle Fluid on page 5-24. Check for leaks.
A uid loss in these systems could indicate a problem.
Have the system inspected and repaired at once.
At Least Once a Year
Key Lock Cylinders Service
Lubricate the key lock cylinders with the lubricant
specied in Part D.
Seat Operation Check
Make sure the head restraints stay in position and all
seat latches lock. Check that the recliner holds by
pushing and pulling the seatback while it is reclined.
Body Lubrication Service
Lubricate all hood latch assembly, secondary latch,
pivots, spring anchor, release pawl, hood and body door
hinges, rear compartment, and any folding seat
hardware. Part D tells you what to use. More frequent
lubrication may be required when exposed to a corrosive
environment.
6-14

Starter Switch Check
{CAUTION:
When you are doing this inspection, the
vehicle could move suddenly. If the vehicle
moves, you or others could be injured.
1. Before you start, be sure you have enough room
around the vehicle.
2. Firmly apply both the parking brake and the regular
brake. SeeParking Brake on page 2-24.
Do not use the accelerator pedal, and be ready to
turn off the engine immediately if it starts.
3. On automatic transaxle vehicles, try to start the
engine in each gear. The vehicle should start only in
PARK (P) or NEUTRAL (N). If the vehicle starts in
any other position, your vehicle needs service.
On manual transaxle vehicles, put the shift lever
in NEUTRAL (N), push the clutch down halfway, and
try to start the engine. The vehicle should start
only when the clutch is pushed down all the way to
the oor. If the vehicle starts when the clutch
is not pushed all the way down, your vehicle
needs service.
Automatic Transaxle Shift Lock Control
System Check
{CAUTION:
When you are doing this inspection, the
vehicle could move suddenly. If the vehicle
moves, you or others could be injured.
1. Before you start, be sure you have enough room
around the vehicle. It should be parked on a level
surface.
2. Firmly apply the parking brake. SeeParking Brake
on page 2-24.
Be ready to apply the regular brake immediately
if the vehicle begins to move.
3. With the engine off, turn the ignition to ON, but do
not start the engine. Without applying the regular
brake, try to move the shift lever out of PARK (P)
with normal effort. If the shift lever moves out
of PARK (P), your vehicle needs service.
6-15

Ignition Transaxle Lock Check
While parked, and with the parking brake set, try to turn
the ignition to LOCK in each shift lever position.
With an automatic transaxle, the ignition should turn
to LOCK only when the shift lever is in PARK (P).
With a manual transaxle, the ignition should turn to
LOCK only if you push the key in farther, while
turning it toward LOCK.
Parking Brake and Automatic Transaxle
Park (P) Mechanism Check
{CAUTION:
When you are doing this check, your vehicle
could begin to move. You or others could be
injured and property could be damaged.
Make sure there is room in front of your
vehicle in case it begins to roll. Be ready to
apply the regular brake at once should the
vehicle begin to move.Park on a fairly steep hill, with the vehicle facing
downhill. Keeping your foot on the regular brake,
set the parking brake.
To check the parking brake’s holding ability:
With the engine running and transaxle in
NEUTRAL (N), slowly remove foot pressure from
the regular brake pedal. Do this until the vehicle is
held by the parking brake only.
To check the PARK (P) mechanism’s holding
ability: With the engine running, shift to PARK (P).
Then release the parking brake followed by the
regular brake.
Underbody Flushing Service
At least every spring, use plain water to ush any
corrosive materials from the underbody. Take care to
clean thoroughly any areas where mud and other debris
can collect.
6-16

Part C: Periodic Maintenance
Inspections
Listed in this part are inspections and services which
should be performed at least twice a year (for instance,
each spring and fall).You should let your dealer’s
service department do these jobs. Make sure any
necessary repairs are completed at once.
Proper procedures to perform these services may be
found in a service manual. SeeService Publications
Ordering Information on page 7-14.
Steering, Suspension and Front
Drive Axle Boot and Seal Inspection
Inspect the front and rear suspension and steering
system for damaged, loose or missing parts, signs of
wear or lack of lubrication. Inspect the power steering
lines and hoses for proper hook-up, binding, leaks,
cracks, chang, etc. Clean and then inspect the
drive axle boot seals for damage, tears or leakage.
Replace seals if necessary.
Exhaust System Inspection
Inspect the complete exhaust system. Inspect the body
near the exhaust system. Look for broken, damaged,
missing or out-of-position parts as well as open seams,
holes, loose connections or other conditions which
could cause a heat build-up in the oor pan or could let
exhaust fumes into the vehicle. SeeEngine Exhaust
on page 2-28.
6-17