ignition PONTIAC VIBE 2007 Workshop Manual

4. Load a CD. Insert the CD partway into
the slot, label side up. The player pulls
the CD in.
To insert multiple CDs, do the following:
1. Turn the ignition on.
2. Press and hold the LOAD button for
two seconds.
A beep sounds and the indicator light, located
to the right of the slot, begins to ash.
3. Once the light stops ashing and turns green,
load a CD. Insert the CD partway into the slot,
label side up. The player pulls the CD in.
Once the CD is loaded, the light begins
ashing again. Once the light stops ashing
and turns green you can load another CD. The
CD player takes up to six CDs. Do not try to
load more than six.
To load more than one CD but less than six,
complete Steps 1 through 3. When nished loading
CDs, the radio begins to play the last CD loaded.
If more than one CD has been loaded, a
number for each CD displays.Playing a Specic Loaded CD
For every CD loaded, a number appears on the
display. To play a specic CD, rst press the
CD AUX button, then press the numbered
pushbutton that corresponds to the CD. A small
bar appears under the CD number that is
playing and the track number displays.
If an error appears on the display, see “CD
Messages” later in this section.
LOAD CD
Z(Eject):Press the CD eject side of
this button to eject a CD(s). To eject the CD
that is currently playing, press and release this
button. To eject multiple CDs, press and hold this
button for two seconds. A beep sounds and
the indicator light ashes while a CD is being
ejected.
REMOVE CD displays. The CD can be removed.
If the CD is not removed, after 25 seconds,
the CD automatically pulls back into the player. If
the CD is pushed back into the player, before
the 25 second time period is complete, the player
senses an error and tries to eject the CD
several times before stopping.
205

File System and Naming
The song name that displays is the song name
that is contained in the ID3 tag. If the song name is
not present in the ID3 tag, then the radio displays
the le name without the extension (such
as .mp3) as the track name.
Track names longer than 39 characters or 3 pages
are shortened. The display does not show parts
of words on the last page of text and the extension
of the lename does not display.
Preprogrammed Playlists
Preprogrammed playlists which were created by
WinAmp™, MusicMatch™, or Real Jukebox™
software can be accessed, however, they cannot
be edited using the radio. These playlists are
treated as special folders containing compressed
audio song les.
Playing an MP3
Insert a CD partway into the slot, label side up.
The player pulls it in, and READING DISC
displays. The CD should begin playing and the
CD symbol displays. If you want to insert a
CD with the ignition off, rst press the eject button
or the RCL button.If the ignition or radio is turned off with a CD in
the player it stays in the player. When the ignition
or radio is turned on, the CD starts to play
where it stopped, if it was the last selected audio
source.
As each new track starts to play, the track number
displays.
The CD player can play the smaller 3 inch (8 cm)
single CDs with an adapter ring. Full-size CDs
and the smaller CDs are loaded in the same
manner.
If playing a CD-R, the sound quality can be
reduced due to CD-R quality, the method of
recording, the quality of the music that has been
recorded, and the way the CD-R has been
handled. There can be an increase in skipping,
difficulty in nding tracks, and/or difficulty in loading
and ejecting. If these problems occur, check the
bottom surface of the CD. If the surface of the CD
is damaged, such as cracked, broken, or
scratched, the CD will not play properly. If the
surface of the CD is soiled, seeCare of Your CDs
on page 219for more information.
If there is no apparent damage, try a known
good CD.
212

RCL (Recall):Push this button to switch between
track mode, folder, or playlist mode, and time of
day mode. The display shows only 13 characters,
but there can be up to three pages of text. If
there are more than 13 characters in the song,
folder, or playlist name pushing this button within
two seconds takes you to the next page of
text. If there are no other pages to be shown,
pushing this button within two seconds takes you
to the next display mode.
Track mode displays the current track number and
the ID3 tag song name.
Folder/playlist mode displays the current folder or
playlist number and the folder/playlist name.
Time of day mode displays the time of day and
the ID3 tag song name.
To change the default on the display, push this
button until you see the desired display, then hold
this button for two seconds. The radio produces
one beep and the selected display is now the
default.INFO (Information):INFO displays whenever a
current track has ID3 tag information. Press
this button to display the artist name and album
contained in the tag. INFO disappears from
the display when the information in the ID3 tag
has nished.
BAND:Press this button to listen to the radio
when a CD is playing. The inactive CD remains
inside the radio for future listening.
CD AUX (Auxiliary):Press this button to play a
CD when listening to the radio. The CD symbol
displays when a CD is loaded.
Z(Eject):Press this button to eject a CD. Eject
may be activated with either the ignition or radio
off. CDs can be loaded with the radio and
ignition off if this button is pressed rst.
215

Traction Control System (TCS)
Your vehicle may have a traction control system
that limits wheel spin. This is especially useful in
slippery road conditions. The system operates only
if it senses that one or both of the front wheels are
spinning or beginning to lose traction. When this
happens, the system works the front brakes and
reduces engine power to limit wheel spin.
You may feel or hear the system working, but this
is normal. Leave the system on during ordinary
driving so that it can operate when needed. When
the ignition is turned to ON, the system
automatically turns on.
This light should come
on briey when you
start the engine.
If it stays on or comes on while you are driving,
there is a problem with your traction control
system.The TRAC OFF button
is located to the left of
the steering wheel
below the instrument
panel cluster.
When getting the vehicle out of mud or newly
fallen snow, turn off the traction control system.
The system that controls engine performance
interferes with the process of freeing the
front wheels. To turn off traction control, press the
TRAC OFF button. The traction control system
warning light will come on. The vehicle stability
control system (StabiliTrak
®) is always activated,
even when the traction control system is turned
off. To turn the traction control system back
on, press the TRAC OFF button again. The
traction control system warning light will go off.
SeeTraction Control System (TCS) Warning Light
on page 168for more information.
Adding non-GM accessories can affect your
vehicle’s performance. SeeAccessories and
Modications on page 272for more information.
230

{CAUTION:
Coasting downhill in NEUTRAL (N) or with
the ignition off is dangerous. The brakes
will have to do all the work of slowing
down. They could get so hot that they
would not work well. You would then have
poor braking or even none going down a
hill. You could crash. Always have the
engine running and your vehicle in gear
when you go downhill.
Know how to go down hills. The most important
thing to know is this: let your engine do some of
the slowing down. Shift to a lower gear when
you go down a steep or long hill.
Know how to go uphill. You may want to shift
down to a lower gear. The lower gears help
cool your engine and transaxle, and you can
climb the hill better.
Stay in your own lane when driving on two-lane
roads in hills or mountains. Do not swing wide
or cut across the center of the road. Drive at
speeds that let you stay in your own lane.
As you go over the top of a hill, be alert. There
could be something in your lane, like a stalled
car or an accident.
You may see highway signs on mountains that
warn of special problems. Examples are long
grades, passing or no-passing zones, a falling
rocks area, or winding roads. Be alert to these
and take appropriate action.
247

Dinghy Towing
If your vehicle has an automatic transaxle, it
cannot be dinghy towed. See “Dolly Towing” for
more information regarding towing your vehicle.
If your vehicle has a manual transaxle, it can
be dinghy towed.
When dinghy towing, be sure to follow the posted
legal speed limit.
1. Put the shift lever in NEUTRAL.2. Turn the ignition to ACC to avoid locking the
steering wheel. Make sure the audio system
is turned off and that nothing is plugged
into the power outlets.
3. Release the parking brake.
After dinghy towing, let the engine idle for more
than three minutes before driving the vehicle.
Do not tow your vehicle from the rear. Your
vehicle could be badly damaged and the repairs
would not be covered by your warranty.
260

1. Check the other vehicle. It must have a
12-volt battery with a negative ground system.
Notice:If the other vehicle’s system is not a
12-volt system with a negative ground,
both vehicles can be damaged. Only use
vehicles with 12-volt systems with negative
grounds to jump start your vehicle.
2. Get the vehicles close enough so the jumper
cables can reach, but be sure the vehicles are
not touching each other. If they are, it could
cause a ground connection you do not
want. You would not be able to start your
vehicle, and the bad grounding could damage
the electrical systems.
To avoid the possibility of the vehicles rolling,
set the parking brake rmly on both vehicles
involved in the jump start procedure. Put
an automatic transaxle in PARK (P) or
a manual transaxle in NEUTRAL before
setting the parking brake.Notice:If you leave your radio or other
accessories on during the jump starting
procedure, they could be damaged. The repairs
would not be covered by your warranty.
Always turn off your radio and other
accessories when jump starting your vehicle.
3. Turn off the ignition on both vehicles.
Unplug unnecessary accessories plugged into
the cigarette lighter. Turn off the radio and
all lamps that are not needed. This will avoid
sparks and help save both batteries. And
it could save the radio!
311

This light, on the
instrument panel cluster,
comes on when the
tire pressure monitoring
system detects a
low-tire condition.
This light also comes on for a few seconds and
then go off when you turn the ignition to ON. This
indicates that the TPMS is functioning properly.
If the low-tire pressure warning light comes
on while driving your vehicle, the system may
have detected a low-tire condition. You need to
stop as soon as possible and check your tires
for damage. If a tire is at, seeIf a Tire Goes Flat
on page 342andChanging a Flat Tire on
page 343. Also check the tire pressure in all four
tires, and set them to the specied level shown
on the Tire and Loading Information label.SeeInation - Tire Pressure on page 329and
Loading Your Vehicle on page 253for additional
information.
Note:The tire pressure monitoring system on your
vehicle warns you when one of the tires is
signicantly under-inated and when some
combinations of the tires are signicantly
under-inated. However, there are other
combinations of signicantly under-inated tires for
which the tire pressure monitoring system might not
give a warning. These other combinations are
relatively common, accounting for approximately
half the instances in which vehicles have
signicantly under-inated tires. For example, the
system might not warn you when both tires on the
same side or on the same axle of your vehicle are
signicantly under-inated. It is particularly
important, therefore, to check the tire pressure in all
of the tires regularly and maintain proper pressure.
In order for the tire pressure monitoring system to
work properly you need to reset (initialize) the
tire pressure monitoring system. Any time
you check and/or adjust a tire’s pressure, repair or
replace a tire or wheel, or rotate the tires the
tire pressure monitor system needs to be reset.
331

Do not reset (initialize) the system without rst
correcting the cause of the low-tire condition. If the
system is reset when the tire pressures are
incorrect, the system will not function properly and
might not alert you when a tire is low.
To reset (initialize) the system:
1. Park the vehicle at a safe place and apply the
parking brake. Turn the engine off.
2. Turn the ignition to ON with the engine off.
3. If the low-tire
pressure warning
light is on, push
the SET (reset)
button for a
few seconds.
The reset button is on the instrument panel to
the left of the steering wheel. The low-tire
warning light should go off.4. Press and hold the SET (reset) button until
the low-tire warning light comes on and
ashes on/off three times. The tire pressure
warning reset button starts the reset
(initialization) process.
If the low-tire pressure warning light does not
ash while you hold the reset button, the
system might be malfunctioning and needs
service. See your GM dealer for service.
The system completes the reset (initialization)
process after driving at vehicle speeds of at least
19 mph (30 km/h) to 62 mph (100 km/h) for
more than one hour. Do not push the SET (reset)
button while driving. If you do the initialization
process is cancelled. The initialization process can
take up to approximately one hour of driving
under the following conditions:
The vehicle speed is between 31 mph
(50 km/h) and 62 mph (100 km/h).
The roads are dry, smooth, and straight.
The number of passengers is one or
two (including the driver).
332

3. On automatic transaxle vehicles, try to start
the engine in each gear. The vehicle should
start only in PARK (P) or NEUTRAL (N). If the
vehicle starts in any other position, contact
your GM Goodwrench
®dealer for service.
On manual transaxle vehicles, put the
shift lever in NEUTRAL (N), push the clutch
pedal down halfway, and try to start the
engine. The vehicle should start only when
the clutch pedal is pushed down all the way to
the oor. If the vehicle starts when the
clutch pedal is not pushed all the way down,
contact your GM Goodwrench
®dealer for
service.
Automatic Transaxle Shift Lock Control
System Check
{CAUTION:
When you are doing this inspection, the
vehicle could move suddenly. If the
vehicle moves, you or others could be
injured.
1. Before you start, be sure you have enough
room around the vehicle. It should be parked
on a level surface.
2. Firmly apply the parking brake. SeeParking
Brake on page 114.
Be ready to apply the regular brake
immediately if the vehicle begins to move.
3. With the engine off, turn the ignition to ON,
but do not start the engine. Without applying
the regular brake, try to move the shift
lever out of PARK (P) with normal effort. If the
shift lever moves out of PARK (P), contact
your GM Goodwrench
®dealer for service.
389