tire pressure reset PONTIAC VIBE 2007 Owners Manual

The main components of your instrument panel are the following:
A. Air Outlets. SeeOutlet Adjustment on
page 155.
B. Instrument Panel Cluster. SeeInstrument
Panel Cluster on page 159.
C. Climate Control System. SeeClimate Control
System on page 152.
D. Hazard Warning Flasher Button. SeeHazard
Warning Flashers on page 138.
E. Audio System. SeeAudio System(s) on
page 177.
F. Rear Window Defogger Button. See “Rear
Window Defogger” underClimate Control
System on page 152.
G. Passenger Airbag Status Indicator. See
Passenger Airbag Status Indicator on page 163.
Front Passenger Safety Belt Reminder Light.
SeeSafety Belt Reminder Light on page 161.
H. Power Remote Control Mirror Button. See
Outside Remote Control Mirrors on page 122.
I. Instrument Panel Brightness Control. See
Instrument Panel Brightness on page 148.
J. Rear Liftglass Release Button. See
Liftgate/Liftglass on page 96.K. Tire Pressure Monitor Reset Button. SeeTire
Pressure Monitor System on page 330.
L. Coinholder. SeeCoinholder(s) on page 127.
M. TRAC OFF Button. SeeTraction Control
System (TCS) on page 230.
N. Content Theft-Deterrent Security Light. See
Content Theft-Deterrent on page 100.
O. Storage Compartment. SeeInstrument Panel
Storage Area on page 127.
P. Turn Signal/Multifunction Lever and Exterior
Lamp Stalk. SeeTurn Signal/Multifunction
Lever on page 139andExterior Lamps
on page 146.
Q. Hood Release. SeeHood Release on
page 280.
R. Tilt Lever. SeeTilt Wheel on page 139.
S. Horn. SeeHorn on page 138.
T. Cruise Control Lever (Option). SeeCruise
Control on page 143.
U. Ignition Switch. SeeIgnition Positions on
page 103.
137

Anti-Lock Brake System
Warning Light
With the Anti-Lock Brake System (ABS), this light
comes on when the engine is started and can
stay on for several seconds. This is normal.
If the light stays on, turn the ignition to LOCK. If
the light comes on while you are driving, stop
as soon as possible and turn the ignition off. Then
start the engine again to reset the system. If
the light still stays on, or comes on again while
you are driving, your vehicle needs service. If the
regular brake system warning light is not on,
you still have brakes, but you do not have anti-lock
brakes. If the regular brake system warning light
is also on, you do not have anti-lock brakes
and there is a problem with the regular brakes.
SeeBrake System Warning Light on page 166.The ABS warning light comes on briey when you
turn the ignition key to ON. This is normal. If
the light does not come on then, have it xed so it
will be ready to warn you if there is a problem.
Low Tire Pressure Warning Light
This light should come
on briey as you start
the engine.
It will then come on only when a low tire pressure
condition exists.
SeeTire Pressure Monitor System on page 330
for more information.
United StatesCanada
167

This light, on the
instrument panel cluster,
comes on when the
tire pressure monitoring
system detects a
low-tire condition.
This light also comes on for a few seconds and
then go off when you turn the ignition to ON. This
indicates that the TPMS is functioning properly.
If the low-tire pressure warning light comes
on while driving your vehicle, the system may
have detected a low-tire condition. You need to
stop as soon as possible and check your tires
for damage. If a tire is at, seeIf a Tire Goes Flat
on page 342andChanging a Flat Tire on
page 343. Also check the tire pressure in all four
tires, and set them to the specied level shown
on the Tire and Loading Information label.SeeInation - Tire Pressure on page 329and
Loading Your Vehicle on page 253for additional
information.
Note:The tire pressure monitoring system on your
vehicle warns you when one of the tires is
signicantly under-inated and when some
combinations of the tires are signicantly
under-inated. However, there are other
combinations of signicantly under-inated tires for
which the tire pressure monitoring system might not
give a warning. These other combinations are
relatively common, accounting for approximately
half the instances in which vehicles have
signicantly under-inated tires. For example, the
system might not warn you when both tires on the
same side or on the same axle of your vehicle are
signicantly under-inated. It is particularly
important, therefore, to check the tire pressure in all
of the tires regularly and maintain proper pressure.
In order for the tire pressure monitoring system to
work properly you need to reset (initialize) the
tire pressure monitoring system. Any time
you check and/or adjust a tire’s pressure, repair or
replace a tire or wheel, or rotate the tires the
tire pressure monitor system needs to be reset.
331

Do not reset (initialize) the system without rst
correcting the cause of the low-tire condition. If the
system is reset when the tire pressures are
incorrect, the system will not function properly and
might not alert you when a tire is low.
To reset (initialize) the system:
1. Park the vehicle at a safe place and apply the
parking brake. Turn the engine off.
2. Turn the ignition to ON with the engine off.
3. If the low-tire
pressure warning
light is on, push
the SET (reset)
button for a
few seconds.
The reset button is on the instrument panel to
the left of the steering wheel. The low-tire
warning light should go off.4. Press and hold the SET (reset) button until
the low-tire warning light comes on and
ashes on/off three times. The tire pressure
warning reset button starts the reset
(initialization) process.
If the low-tire pressure warning light does not
ash while you hold the reset button, the
system might be malfunctioning and needs
service. See your GM dealer for service.
The system completes the reset (initialization)
process after driving at vehicle speeds of at least
19 mph (30 km/h) to 62 mph (100 km/h) for
more than one hour. Do not push the SET (reset)
button while driving. If you do the initialization
process is cancelled. The initialization process can
take up to approximately one hour of driving
under the following conditions:
The vehicle speed is between 31 mph
(50 km/h) and 62 mph (100 km/h).
The roads are dry, smooth, and straight.
The number of passengers is one or
two (including the driver).
332

The low-tire pressure warning light may not come
on even if the tire ination pressure is low, or it
could come on when the tire ination pressure is
set correctly under the following circumstances:
A compact spare tire, snow tires, or tire chains
are installed on your vehicle.
The tires are over-inated, or the tire ination
pressure suddenly drops due to a tire bursting
or other causes.
The vehicle is driven on a slippery road
surface such as rough or frozen roads.
The vehicle speed is less than
19 mph (30 km/h), and the driving duration is
less than ve minutes.
The tires are made by a different manufacturer
or differ in tread pattern than the original
equipment tires.
Rapid acceleration/deceleration or multiple
consecutive sharp turns.
Towing a trailer.
The vehicle is loaded over the limit or not
balanced properly.
The initialization (reset) procedure was not
performed correctly after replacing or
rotating tires or wheels.
The outside temperature is below 32°F (0°C)
or above 104°F (40°C).
Tire Inspection and Rotation
Tires should be rotated every 5,000 to 8,000 miles
(8 000 to 13 000 km).
Any time you notice unusual wear, rotate your
tires as soon as possible and check wheel
alignment. Also check for damaged tires or wheels.
SeeWhen It Is Time for New Tires on page 335
andWheel Replacement on page 340for
more information.
The purpose of regular rotation is to achieve
more uniform wear for all tires on the vehicle.
The rst rotation is the most important. See
Part A: Scheduled Maintenance Services on
page 376for scheduled rotation intervals.
333

When rotating your tires, always use the correct
rotation pattern shown here.
Tires should only be moved from front to rear and
rear to front on the same side of the vehicle.
Do not include the compact spare tire in your tire
rotation.
After the tires have been rotated, adjust the front
and rear ination pressures to the amounts
shown on the Tire and Loading Information label.Make certain that all wheel nuts are properly
tightened. See “Wheel Nut Torque” under
Capacities and Specications on page 369.
{CAUTION:
Rust or dirt on a wheel, or on the parts to
which it is fastened, can make wheel nuts
become loose after time. The wheel could
come off and cause an accident. When
you change a wheel, remove any rust or
dirt from places where the wheel attaches
to the vehicle. In an emergency, you can
use a cloth or a paper towel to do this;
but be sure to use a scraper or wire brush
later, if needed, to get all the rust or dirt
off. SeeChanging a Flat Tire on page 343.
Vehicles equipped with a tire pressure monitoring
system will need to reset (initialize) the system
after each tire rotation. SeeTire Pressure Monitor
System on page 330.
334