warning light PONTIAC VIBE 2009 Owner's Manual

Driving in Rain and on
Wet Roads
Rain and wet roads can reduce
vehicle traction and affect your
ability to stop and accelerate.
Always drive slower in these types
of driving conditions and avoid
driving through large puddles and
deep-standing or owing water.
{CAUTION
Wet brakes can cause crashes.
They might not work as well in
a quick stop and could cause
pulling to one side. You could
lose control of the vehicle.
After driving through a large
puddle of water or a car/vehicle
wash, lightly apply the brake
pedal until the brakes work
normally.
(Continued)
CAUTION (Continued)
Flowing or rushing water creates
strong forces. Driving through
owing water could cause your
vehicle to be carried away. If this
happens, you and other vehicle
occupants could drown. Do not
ignore police warnings and be
very cautious about trying to
drive through owing water.
Hydroplaning
Hydroplaning is dangerous. Water
can build up under your vehicle’s
tires so they actually ride on the
water. This can happen if the road
is wet enough and you are going
fast enough. When your vehicle is
hydroplaning, it has little or no
contact with the road.There is no hard and fast rule about
hydroplaning. The best advice is
to slow down when the road is wet.
Other Rainy Weather Tips
Besides slowing down, other wet
weather driving tips include:
Allow extra following distance.
Pass with caution.
Keep windshield wiping
equipment in good shape.
Keep the windshield washer uid
reservoir lled.
Have good tires with proper tread
depth. SeeTires on page 9-41.
Turn off cruise control, if
equipped.
Driving and Operating 8-27
2009 - Pontiac Vibe Owner Manual

{CAUTION
Adding only plain water to the
cooling system can be dangerous.
Plain water, or some other liquid
such as alcohol, can boil before
the proper coolant mixture will.
The vehicle’s coolant warning
system is set for the proper
coolant mixture. With plain water
or the wrong mixture, the engine
could get too hot but would not
get the overheat warning. The
engine could catch re and you
or others could be burned. Use a
50/50 mixture of clean, drinkable
water and DEX-COOL
®coolant.
Notice:If an improper coolant
mixture is used, the engine could
overheat and be badly damaged.
The repair cost would not be
covered by the vehicle warranty.
Too much water in the mixture
can freeze and crack the engine,
radiator, heater core, and other
parts.Notice:If you use extra
inhibitors and/or additives in
your vehicle’s cooling system,
you could damage your vehicle.
Use only the proper mixture of
the engine coolant listed in this
manual for the cooling system.
SeePart D: Recommended Fluids
and Lubricants on page 11-18for
more information.
Gives freezing protection down to
−34°F (−38°C).
Gives boiling protection up to
265°F (129°C).
Protects against rust and
corrosion.
Helps keep the proper engine
temperature.
Lets the warning lights and gages
work as they should.
Notice:Using coolant other than
DEX-COOL can cause premature
engine, heater core or radiator
corrosion. In addition, the enginecoolant may require changing
sooner, at 30,000 miles
(50 000 km) or 24 months,
whichever occurs rst. Any
repairs would not be covered by
the vehicle warranty. Always
use DEX-COOL (silicate-free)
coolant in your vehicle.
Checking Coolant
The vehicle must be on a level
surface. When the engine is cold,
the coolant level should be at LOW,
or a little higher. When the engine
is warm, the level should be up to
FULL, or a little higher. If it is not,
there could be a leak at the pressure
cap or in the radiator hoses, heater
hoses, radiator, water pump, or
somewhere else in the cooling
system.
SeeEngine Compartment Overview
on page 9-6Engine Compartment
Overview for the location of the
coolant recovery tank.
Vehicle Service and Care 9-19
2009 - Pontiac Vibe Owner Manual

Do not top off the brake/clutch uid.
Adding uid does not correct a leak.
If uid is added when the brake
linings are worn, there will be too
much uid when new brake linings
are installed. Add or remove uid, as
necessary, only when work is done
on the brake/clutch hydraulic system.
{CAUTION
If too much brake uid is added, it
can spill on the engine and burn,
if the engine is hot enough. You
or others could be burned, and
the vehicle could be damaged.
Add brake uid only when work
is done on the brake hydraulic
system.
When the brake uid falls to a low
level, the brake warning light comes
on. SeeBrake System Warning
Light on page 4-17.What to Add
Use only new DOT-3 brake uid
from a sealed container. See
Part D: Recommended Fluids
and Lubricants on page 11-18.
Always clean the brake uid
reservoir cap and the area around
the cap before removing it. This
helps keep dirt from entering the
reservoir.{CAUTION
With the wrong kind of uid in the
brake or clutch hydraulic system,
the brakes or clutch might not
work well. This could cause a
crash. Always use the proper
brake uid.Notice:
Using the wrong uid can
badly damage brake or clutch
hydraulic system parts.
For example, just a few drops
of mineral-based oil, such as
engine oil, in the brake or clutch
hydraulic system can damage
brake or clutch hydraulic
system parts so badly that they
will have to be replaced. Do not
let someone put in the wrong
kind of uid.
If brake uid is spilled on the
vehicle’s painted surfaces, the
paint nish can be damaged.
Be careful not to spill brake
uid on the vehicle. If you do,
wash it off immediately. See
Exterior Cleaning on page 9-86.
9-28 Vehicle Service and Care
2009 - Pontiac Vibe Owner Manual

Brake Wear
This vehicle has disc brakes.
Disc brake pads have built-in wear
indicators that make a high-pitched
warning sound when the brake
pads are worn and new pads are
needed. The sound can come
and go or be heard all the time
the vehicle is moving, except when
applying the brake pedal rmly.
{CAUTION
The brake wear warning sound
means that soon the brakes will
not work well. That could lead to
an accident. When the brake wear
warning sound is heard, have the
vehicle serviced.
Notice:Continuing to drive
with worn-out brake pads could
result in costly brake repair.Some driving conditions or climates
can cause a brake squeal when the
brakes are rst applied or lightly
applied. This does not mean
something is wrong with the brakes.
Properly torqued wheel nuts are
necessary to help prevent brake
pulsation. When tires are rotated,
inspect brake pads for wear and
evenly tighten wheel nuts in
the proper sequence to torque
specications inCapacities and
Specifications on page 10-2.
Brake linings should always be
replaced as complete axle sets.
Brake Pedal Travel
See your dealer/retailer if the brake
pedal does not return to normal
height, or if there is a rapid increase
in pedal travel. This could be a sign
that brake service might be required.
Brake Adjustment
Every time the brakes are applied,
with or without the vehicle moving,
the brakes adjust for wear.
Replacing Brake System Parts
The braking system on a vehicle is
complex. Its many parts have to be
of top quality and work well together
if the vehicle is to have really good
braking. The vehicle was designed
and tested with top-quality brake
parts. When parts of the braking
system are replaced — for example,
when the brake linings wear down
and new ones are installed — be
sure to get new approved
replacement parts. If this is not done,
the brakes might not work properly.
For example, if someone puts in
brake linings that are wrong for
the vehicle, the balance between
the front and rear brakes can
change — for the worse. The braking
performance expected can change
in many other ways if the wrong
replacement brake parts are
installed.
Vehicle Service and Care 9-29
2009 - Pontiac Vibe Owner Manual

The TPMS operates on a radio
frequency and complies with
RSS-210 of Industry and Science
Canada. Operation is subject to
the following two conditions:
1. This device may not cause
interference.
2. This device must accept any
interference received, including
interference that may cause
undesired operation of the device.
Changes or modications to
this system by other than an
authorized service facility could void
authorization to use this equipment.
Tire Pressure Monitor
Operation
The Tire Pressure Monitor System
(TPMS) warns the driver when a low
tire pressure condition exists. TPMS
sensors are mounted onto each tire
and wheel assembly, excluding the
spare tire and wheel assembly.When a low tire pressure condition
is detected, the low tire pressure
warning light, located on the
instrument panel cluster, comes on.
This light also comes on for a
few seconds and then goes off when
you turn the ignition to ON/RUN.
This indicates the TPMS is
functioning properly. If the low-tire
pressure warning light comes on
while driving the vehicle, the system
may have detected a low-tire
condition. You need to stop as soon
as possible and check the tires.
The low tire pressure warning light
may come on in cool weather when
the vehicle is rst started, and
then turn off as you start to drive.This could be an early indicator that
the air pressure in the tire(s) are
getting low and need to be inated
to the proper pressure.
A Tire and Loading Information
label, attached to the vehicle, shows
the size of the vehicle’s original
equipment tires and the correct
ination pressure for the tires when
they are cold. SeeLoading the
Vehicle on page 8-32, for an
example of the Tire and Loading
Information label and its location on
your vehicle. Also seeInflation - Tire
Pressure on page 9-47.
The vehicle’s TPMS can warn you
about a low tire pressure condition
but it does not replace normal tire
maintenance. SeeTire Inspection
and Rotation on page 9-53andTires
on page 9-41.
9-50 Vehicle Service and Care
2009 - Pontiac Vibe Owner Manual

TPMS Malfunction Light
The TPMS will not function properly
if one or more of the TPMS sensors
are missing or inoperable. When the
system detects a malfunction, the
low tire warning light ashes for
about one minute and then stays
on for the remainder of the ignition
cycle. The low tire warning light
comes on at each ignition cycle until
the problem is corrected. Some of
the conditions that can cause the
malfunction light to come on are:
One of the road tires has been
replaced with the spare tire. The
spare tire does not have a TPMS
sensor. The TPMS malfunction
light and DIC message should go
off once you re-install the road tire
containing the TPMS sensor.
The initialization (reset) procedure
failed. See “TPMS Reset” later in
this section.
One or more TPMS sensors
are missing or damaged.
The TPMS malfunction light
should go off when the TPMS
sensors are installed and the
sensor matching process is
performed successfully. See
your dealer/retailer for service.
Replacement tires or wheels do
not match the vehicle’s original
equipment tires or wheels. Tires
and wheels other than those
recommended for your vehicle
could prevent the TPMS from
functioning properly. SeeBuying
New Tires on page 9-54.
Operating electronic devices or
being near facilities using radio
wave frequencies similar to the
TPMS could cause the TPMS
sensors to malfunction.
If tire chains are installed on the
vehicle.
If there is a lot of snow or ice
around the wheels or wheel
housings.
If a window tint that affects the
radio wave signals is installed.
If the TPMS is not functioning it
cannot detect or signal a low tire
condition. See your dealer/retailer for
service if the TPMS malfunction light
comes on and stays on.
Vehicle Service and Care 9-51
2009 - Pontiac Vibe Owner Manual

TPMS Reset
The TPMS sensors and transmitters
have unique identication codes.
Anytime you replace a TPMS sensor
or transmitter the identication codes
need to be registered and the TPMS
needs to be reset (initialized). When
the system is initialized, the current
air pressure in the tires is set as the
tire pressure benchmark. The tire
pressure warning system determines
decreased air pressure by comparing
tire pressure to the benchmark
pressure stored in the TPMS.
Do not reset the TPMS without rst
correcting the cause of a low-tire
condition.
To reset the system:
1. Park the vehicle at a safe place
and apply the parking brake.
Turn the engine off.
2. Turn the ignition to
ACC/ACCESSORY or
LOCK/OFF.3. Adjust the tire pressure of all the
installed tires to the specied
cold tire ination pressure level
indicated on the Tire and Loading
Information label attached to
the vehicle.
4. Turn the ignition to ON/RUN with
the engine off.
5. Press and hold the tire pressure
warning reset switch until the tire
pressure warning light ashes
slowly on/off three times.Wait for a few minutes with the
ignition in ON/RUN, and then turn
the ignition to ACC/ACCESSORY
or LOCK/OFF.
If the low-tire pressure warning
light does not ash three times
while you press and hold the
reset button, the reset has failed.
Repeat the reset process. If the
reset cannot be performed, see
your dealer/retailer for service.
If you press the tire pressure reset
switch while the vehicle is moving,
the reset is not performed. If you
press the tire pressure reset switch
accidentally and initialization is
performed, adjust the tire pressure
to the specied level and perform
the reset procedure again.
9-52 Vehicle Service and Care
2009 - Pontiac Vibe Owner Manual

The grades are molded on
the sidewalls of most passenger
car tires. The Uniform Tire
Quality Grading (UTQG)
system does not apply to deep
tread, winter-type snow tires,
space-saver, or temporary use
spare tires, tires with nominal
rim diameters of 10 to 12 inches
(25 to 30 cm), or to some
limited-production tires.
While the tires available on
General Motors passenger
cars and light trucks may vary
with respect to these grades,
they must also conform to
federal safety requirements.Treadwear
The treadwear grade is a
comparative rating based on the
wear rate of the tire when tested
under controlled conditions on
a specied government test
course. For example, a tire
graded 150 would wear one and
a half (1
12) times as well on the
government course as a tire
graded 100. The relative
performance of tires depends
upon the actual conditions of
their use, however, and may
depart signicantly from the
norm due to variations in driving
habits, service practices,
and differences in road
characteristics and climate.Traction — AA, A, B, C
The traction grades, from
highest to lowest, are AA, A, B,
and C. Those grades represent
the tire’s ability to stop on wet
pavement as measured under
controlled conditions on specied
government test surfaces of
asphalt and concrete. A tire
marked C may have poor
traction performance.
{WARNING
The traction grade assigned
to this tire is based on
straight-ahead braking traction
tests, and does not include
acceleration, cornering,
hydroplaning, or peak traction
characteristics.
Vehicle Service and Care 9-57
2009 - Pontiac Vibe Owner Manual

A
Accessories and
Modications...................... 9-3
Accessory Power Outlets........ 4-9
Adding Equipment to Your
Airbag-Equipped Vehicle....1-34
Additives, Fuel.....................8-37
Add-On Electrical
Equipment.......................9-35
Air Cleaner/Filter, Engine.......9-12
Air Conditioning..................... 7-1
Airbag
Passenger Status
Indicator.......................4-15
Readiness Light................4-14
System, Replacing Parts
After a Crash................1-35
Airbag System.....................1-21
Adding Equipment to
Your Airbag-Equipped
Vehicle........................1-34
Check.............................1-35
How Does an Airbag
Restrain?.....................1-26Airbag System (cont.)
Passenger Sensing
System........................1-28
Servicing Your
Airbag-Equipped
Vehicle........................1-33
What Makes an Airbag
Inate?........................1-26
What Will You See After
an Airbag Inates?........1-26
When Should an Airbag
Inate?........................1-24
Where Are the Airbags?.....1-23
All-Wheel-Drive (AWD)
System...........................8-22
All-Wheel-Drive Service
Light...............................4-24
Antenna, Fixed Mast............6-14
Antenna, XM™ Satellite
Radio Antenna System......6-14
Antilock Brake
System (ABS)..................8-20
Antilock Brake, System
Warning Light...................4-18Appearance Care
Chemical Paint Spotting.....9-90
Exterior Cleaning..............9-86
Finish Damage.................9-89
Interior Cleaning...............9-83
Sheet Metal Damage........9-89
Underbody Maintenance....9-90
Appointments, Scheduling
Service...........................12-8
Ashtray(s)...........................4-10
Audio System........................ 6-1
Audio Steering Wheel
Controls.......................6-13
Fixed Mast Antenna..........6-14
Radio Reception...............6-14
Setting the Clock................ 6-2
XM™ Satellite Radio
Antenna System............6-14
Audio System(s).................... 6-3
Automatic Headlamp System . . . 5-2
Automatic Transmission
Fluid...............................9-14
Operation....................8-6, 8-8
INDEX i-1
2009 - Pontiac Vibe Owner Manual

B
Battery...............................9-30
Run-Down Protection.......... 5-4
Brake
System Inspection...........11-17
Brake Fluid.........................9-27
Brakes...............................9-27
System Warning Light.......4-17
Braking...............................8-19
Break-In, New Vehicle............ 8-2
Bulb Replacement................9-31
Halogen Bulbs..................9-31
Headlamp Aiming..............9-30
Headlamps and Parking
Lamps .........................9-31
License Plate Lamps.........9-34
Replacement Bulbs...........9-35
Taillamps.........................9-33
Buying New Tires.................9-54
C
California Fuel.....................8-36
California Perchlorate
Materials Requirements....... 9-3
California Proposition
65 Warning........................ 9-3
Canadian Owners..................... iiCapacities and
Specications...................10-2
Carbon Monoxide.........8-16, 8-29
Care, Safety Belts................1-20
Cargo Cover......................... 3-4
Cargo Management System.... 3-6
Cargo Tie Downs................... 3-6
Cautions and Notices............... iii
CD, MP3 .............................. 6-9
Center Console Storage Area . . . 3-2
Chains, Tire........................9-60
Charging System Light..........4-16
Check
Engine Lamp...................4-20
Chemical Paint Spotting........9-90
Child Restraints
Child Restraint Systems.....1-41
Infants and Young
Children.......................1-38
Lower Anchors and Tethers
for Children..................1-44
Older Children..................1-36
Securing..................1-50, 1-53
Where to Put the
Restraint......................1-43
Cleaning
Exterior...........................9-86
Interior............................9-83
Underbody Maintenance....9-90Climate Control System.......... 7-1
Air Filter, Passenger
Compartment.................. 7-4
Outlet Adjustment............... 7-3
Clock, Setting........................ 6-2
Clutch, Hydraulic..................9-17
Collision Damage Repair.....12-11
Compact Spare Tire.............9-70
Content Theft-Deterrent.........2-10
Control of a Vehicle..............8-18
Coolant
Engine............................
9-18
Engine
Temperature Gage.........4-19
Cooling System...................9-18
Cruise Control....................... 4-4
Cruise Control Light..............4-23
Cupholders........................... 3-1
Customer Assistance
Information
Courtesy
Transportation.....12-4, 12-10
Customer Assistance
Offices.........................12-4
Customer Satisfaction
Procedure....................12-1
i-2 INDEX
2009 - Pontiac Vibe Owner Manual