instrument panel PONTIAC VIBE 2009 Owner's Guide

Blizzard Conditions
Being stuck in snow can be in
a serious situation. Stay with the
vehicle unless there is help nearby.
If possible, use theRoadside
Assistance Program on page 12-5.
To get help and keep everyone in
the vehicle safe:
Turn on theHazard Warning
Flashers on page 4-3.
Tie a red cloth to an outside
mirror.
{CAUTION
Snow can trap engine exhaust
under the vehicle. This may cause
exhaust gases to get inside.
Engine exhaust contains carbon
monoxide (CO) which cannot be
seen or smelled. It can cause
unconsciousness and even death.
(Continued)
CAUTION (Continued)
If the vehicle is stuck in the snow:
Clear away snow from
around the base of your
vehicle, especially any that
is blocking the exhaust pipe.
Check again from time to
time to be sure snow does
not collect there.
Open a window about
two inches on the side of
the vehicle that is away from
the wind to bring in fresh air.
Fully open the air outlets
on or under the instrument
panel.
Adjust the Climate Control
system to a setting that
circulates the air inside
the vehicle and set the fan
speed to the highest setting.
See Climate Control System
in the Index.
(Continued)
CAUTION (Continued)
For more information about
carbon monoxide, seeEngine
Exhaust on page 8-16.
Snow can trap exhaust gases
under your vehicle. This can
cause deadly CO (carbon
monoxide) gas to get inside. CO
could overcome you and kill you.
You cannot see it or smell it, so
you might not know it is in your
vehicle. Clear away snow from
around the base of your vehicle,
especially any that is blocking the
exhaust
Run the engine for short periods
only as needed to keep warm,
but be careful.
8-30 Driving and Operating
2009 - Pontiac Vibe Owner Manual

Vehicle Service
and Care
Service
Service...............................9-2
Accessories and
Modications.....................9-3
California Proposition
65 Warning.......................9-3
California Perchlorate
Materials Requirements.....9-3
Doing Your Own
Service Work....................9-4
Adding Equipment to the
Outside of the Vehicle......9-4
Owner Checks
Owner Checks....................9-5
Hood Release.....................9-5
Engine Compartment
Overview...........................9-6
Engine Oil..........................9-9
Engine Air Cleaner/Filter. . . .9-12
Automatic Transmission
Fluid................................9-14
Manual Transmission
Fluid................................9-16
Hydraulic Clutch................9-17
Cooling System.................9-18
Engine Coolant.................9-18
Pressure Cap....................9-22
Engine Overheating...........9-22
Power Steering Fluid.........9-24
Windshield Washer Fluid. . .9-24
Windshield Wiper Blade
Replacement...................9-25
Brakes..............................9-27
Battery..............................9-30
Headlamp Aiming
Headlamp Aiming..............9-30
Bulb Replacement
Bulb Replacement.............9-31
Halogen Bulbs..................9-31
Headlamps and Parking
Lamps.............................9-31
Taillamps..........................9-33
License Plate Lamp..........9-34
Replacement Bulbs...........9-35
Electrical System
Add-On Electrical
Equipment.......................9-35
Headlamp Wiring..............9-35
Windshield Wiper Fuses. . . .9-36
Power Windows and
Other Power Options.......9-36
Fuses and Circuit
Breakers.........................9-36
Instrument Panel Fuse
Block...............................9-36
Engine Compartment
Fuse Block......................9-39
Tires
Tires.................................9-41
Tire Sidewall Labeling.......9-42
Tire Terminology and
Denitions.......................9-44
Ination - Tire Pressure. . . .9-47
Tire Pressure Monitor
System............................9-48
Tire Pressure Monitor
Operation........................9-50
Tire Inspection and
Rotation..........................9-53
When It Is Time for New
Tires...............................9-54
Vehicle Service and Care 9-1
2009 - Pontiac Vibe Owner Manual

Owner Checks
{CAUTION
An electric fan under the hood
can start up and injure you even
when the engine is not running.
Keep hands, clothing, and tools
away from any underhood
electric fan.
{CAUTION
Things that burn can get on hot
engine parts and start a re. These
include liquids like fuel, oil, coolant,
brake uid, windshield washer and
other uids, and plastic or rubber.
You or others could be burned.
Be careful not to drop or spill
things that will burn onto a hot
engine.
Hood Release
To open the hood:
1. Pull the release handle, located
below the instrument panel to
the left of the steering wheel.2. From the front of the vehicle,
pull up on the secondary
hood release located near
the middle of the hood.
3. Lift the hood.
4. Release the hood prop rod from
its retainer and insert into the slot,
moving it straight up. If it is moved
to the side or toward the inside
of the vehicle, it may become
detached.
Before closing the hood, be sure
all the ller caps are on properly.
Return the hood prop rod carefully
back to its retainer to avoid
damaging the vehicle.
Vehicle Service and Care 9-5
2009 - Pontiac Vibe Owner Manual

4. Then ll the coolant recovery
tank to the FULL mark.
5. Put the cap back on the coolant
recovery tank, but leave the
pressure cap off.
6. Start the engine and let it run
until you can feel the upper
radiator hose getting hot. Watch
out for the engine cooling fan.
7. By this time, the coolant level
inside the radiator ller neck may
be lower. If the level is lower,
add more of the proper coolant
mixture through the ller neck
until the level reaches the base
of the ller neck.
8. Then replace the pressure cap.
At any time during this procedure
if coolant begins to ow out of
the ller neck, reinstall the
pressure cap. Be sure the ears
on the pressure cap are in
line with the vent tube.Pressure Cap
Notice:If the pressure cap is not
tightly installed, coolant loss and
possible engine damage may
occur. Be sure the cap is properly
and tightly secured.
SeeEngine Compartment Overview
on page 9-6for more information
on location.
Engine Overheating
A coolant temperature gage is
located on the vehicle’s instrument
panel. SeeEngine Coolant
Temperature Gage on page 4-19.
Check to see if the electric engine
cooling fan is running. If the engine
is overheating, the fan should be
running. If it is not, the vehicle
needs service.If no problem is apparent, but the
coolant level is not at or above the
FULL mark, add a 50/50 mixture
of clean, drinkable water and
DEX-COOL
®coolant at the coolant
recovery tank. SeeEngine Coolant
on page 9-18for more information
about the proper coolant mixture.
If the coolant inside the coolant
recovery tank is boiling, do not do
anything else until it cools down.
The vehicle should be parked on
a level surface.
9-22 Vehicle Service and Care
2009 - Pontiac Vibe Owner Manual

Windshield Wiper Fuses
The windshield wiper motor is
protected by a circuit breaker and
a fuse. If the motor overheats due
to heavy snow or ice, the wiper will
stop until the motor cools. If the
overload is caused by some
electrical problem, and not snow
or ice, be sure to get it xed.
Power Windows and
Other Power Options
Circuit breakers in the fuse block
protect the power windows and other
power accessories. When the current
load is too heavy, the circuit breaker
opens and closes, protecting the
circuit until the problem is xed or
goes away.
Fuses and Circuit
Breakers
The wiring circuits in the vehicle
are protected from short circuits
by a combination of fuses, circuit
breakers and fusible thermal
links. This greatly reduces the
chance of res caused by
electrical problems.
Look at the silver-colored band
inside the fuse. If the band is broken
or melted, replace the fuse. Be sure
you replace a bad fuse with a new
one of the identical size and rating.
Fuses of the same amperage
can be temporarily borrowed from
another fuse location, if a fuse goes
out. Replace the fuse as soon as
you can.
Instrument Panel Fuse
Block
The fuse block is located under
the instrument panel on the driver
side of the vehicle.
9-36 Vehicle Service and Care
2009 - Pontiac Vibe Owner Manual

FusesUsage
1 Parking Lamps,
License Plate
Lamps, Taillamp,
Multiport Fuel
Injection System/
Sequential Multiport
Fuel Injection
System, Instrument
Panel Lights
2 Switch IlluminationFuses Usage
3 Power Windows
4 Power Windows
5 Power Windows
6 Sunroof
7 Cigarette Lighter,
Accessory Power
Outlet
Fuses
Usage
8 Outside Rearview
Mirrors, Audio
System, Main Body
Engine Control
Unit (ECU), Clock,
Brake Transmission
Shift Interlock
9 Empty
10 Empty
11 Airbag System,
Multiport Fuel
Injection System/
Sequential Multiport
Fuel Injection
System, Front
Passenger Occupant
Classication
System
12 Gages and Meters
13 Air Conditioning
System, Rear
Window Defogger
14 Windshield Wipers
15 Rear Window Wipers
16 Windshield Washer
Vehicle Service and Care 9-37
2009 - Pontiac Vibe Owner Manual

The TPMS operates on a radio
frequency and complies with
RSS-210 of Industry and Science
Canada. Operation is subject to
the following two conditions:
1. This device may not cause
interference.
2. This device must accept any
interference received, including
interference that may cause
undesired operation of the device.
Changes or modications to
this system by other than an
authorized service facility could void
authorization to use this equipment.
Tire Pressure Monitor
Operation
The Tire Pressure Monitor System
(TPMS) warns the driver when a low
tire pressure condition exists. TPMS
sensors are mounted onto each tire
and wheel assembly, excluding the
spare tire and wheel assembly.When a low tire pressure condition
is detected, the low tire pressure
warning light, located on the
instrument panel cluster, comes on.
This light also comes on for a
few seconds and then goes off when
you turn the ignition to ON/RUN.
This indicates the TPMS is
functioning properly. If the low-tire
pressure warning light comes on
while driving the vehicle, the system
may have detected a low-tire
condition. You need to stop as soon
as possible and check the tires.
The low tire pressure warning light
may come on in cool weather when
the vehicle is rst started, and
then turn off as you start to drive.This could be an early indicator that
the air pressure in the tire(s) are
getting low and need to be inated
to the proper pressure.
A Tire and Loading Information
label, attached to the vehicle, shows
the size of the vehicle’s original
equipment tires and the correct
ination pressure for the tires when
they are cold. SeeLoading the
Vehicle on page 8-32, for an
example of the Tire and Loading
Information label and its location on
your vehicle. Also seeInflation - Tire
Pressure on page 9-47.
The vehicle’s TPMS can warn you
about a low tire pressure condition
but it does not replace normal tire
maintenance. SeeTire Inspection
and Rotation on page 9-53andTires
on page 9-41.
9-50 Vehicle Service and Care
2009 - Pontiac Vibe Owner Manual

Following Distance
Stay at least twice as far behind the
vehicle ahead as you would when
driving your vehicle without a trailer.
This can help you avoid situations
that require heavy braking and
sudden turns.
Passing
More distance in front is needed to
pass when towing a trailer. And,
because the tow vehicle and trailer
are longer, you will need to go
farther beyond the passed vehicle
before you can return to your lane.
Backing Up
Hold the bottom of the steering
wheel with one hand. Then, to move
the trailer to the left, just move that
hand to the left. To move the trailer
to the right, move your hand to the
right. Always back up slowly and, if
possible, have someone guide you.
Making Turns
Notice:Making very sharp turns
while trailering could cause
the trailer to come in contact with
the vehicle. The vehicle could
be damaged. Avoid making very
sharp turns while trailering.
When you are turning with a trailer,
make wider turns than normal.
Do this so your trailer will not strike
soft shoulders, curbs, road signs,
trees or other objects. Avoid jerky or
sudden maneuvers. Signal well in
advance.
Turn Signals When Towing a
Trailer
When you tow a trailer, your vehicle
may need a different turn signal
asher and/or extra wiring. Check
with your dealer/retailer. The arrows
on the instrument panel ash
whenever you signal a turn or lane
change. Properly hooked up, the
trailer lamps also ash, telling other
drivers you are about to turn, change
lanes or stop.When towing a trailer, the arrows
on the instrument panel will ash for
turns even if the bulbs on the trailer
are burned out. Thus, you may think
drivers behind you are seeing your
signal when they are not. It is
important to check occasionally to be
sure the trailer bulbs are still working.
Driving On Grades
Reduce speed and shift to a lower
gearbeforeyou start down a long or
steep downgrade. If you do not shift
down, you might have to use your
brakes so much that they would get
hot and no longer work well.
On a long uphill grade, shift down
and reduce your speed to around
45 mph (70 km/h) to reduce the
possibility of the engine and the
transmission overheating.
Vehicle Service and Care 9-81
2009 - Pontiac Vibe Owner Manual

If any of the soil remains, a
commercial fabric cleaner or spot
lifter may be necessary. When a
commercial upholstery cleaner or
spot lifter is to be used, test a small
hidden area for colorfastness rst.
If the locally cleaned area gives any
impression that a ring formation may
result, clean the entire surface.
After the cleaning process has been
completed, a paper towel can be
used to blot excess moisture
from the fabric or carpet.Leather
A soft cloth dampened with
water can be used to remove dust.
If a more thorough cleaning is
necessary, a soft cloth dampened
with a mild soap solution can be
used. Allow the leather to dry
naturally. Do not use heat to dry.
Never use steam to clean leather.
Never use spot lifters or spot
removers on leather. Many
commercial leather cleaners and
coatings that are sold to preserve
and protect leather may permanently
change the appearance and
feel of your leather and are not
recommended. Do not use silicone
or wax-based products, or those
containing organic solvents to clean
your vehicle’s interior because
they can alter the appearance by
increasing the gloss in a non-uniform
manner. Never use shoe polish on
leather.
Instrument Panel, Vinyl, and
Other Plastic Surfaces
A soft cloth dampened with water
may be used to remove dust.
If a more thorough cleaning is
necessary, a clean soft cloth
dampened with a mild soap solution
can be used to gently remove dust
and dirt. Never use spot lifters or
removers on plastic surfaces.
Many commercial cleaners and
coatings that are sold to preserve
and protect soft plastic surfaces may
permanently change the appearance
and feel of your interior and are not
recommended. Do not use silicone
or wax-based products, or those
containing organic solvents to clean
your vehicle’s interior because
they can alter the appearance by
increasing the gloss in a non-uniform
manner.
Some commercial products may
increase gloss on your instrument
panel. The increase in gloss may
cause annoying reections in the
windshield and even make it difficult
to see through the windshield under
certain conditions.
Vehicle Service and Care 9-85
2009 - Pontiac Vibe Owner Manual

Technical Data
Vehicle Identication
Vehicle Identication
Number (VIN)..................10-1
Service Parts
Identication Label...........10-1
Capacities and
Specications
Capacities and
Specications..................10-2
Normal Maintenance
Replacement Parts
Maintenance
Replacement Parts..........10-4
Engine Drive Belt
Routing...........................10-5
Vehicle Identication
Vehicle Identication
Number (VIN)
This is the legal identier for your
vehicle. It appears on a plate in
the front corner of the instrument
panel, on the driver side. It can
be seen through the windshield from
outside the vehicle. The VIN also
appears on the Vehicle Certication
and Service Parts labels and the
certicates of title and registration.
Engine Identication
The eighth character in the VIN is
the engine code. This code helps
identify the vehicle’s engine,
specications, and replacement
parts. See “Engine Specications”
underCapacities and Specifications
on page 10-2for your vehicle’s
engine code.
Service Parts
Identication Label
This label is on the inside of the
glove box. It is very helpful if
you ever need to order parts.
The label has the following
information:
Vehicle Identication
Number (VIN)
Model designation
Paint information
Production options and special
equipment
Do not remove this label from the
vehicle.
Technical Data 10-1
2009 - Pontiac Vibe Owner Manual