window PORSCHE 911 GT3 2010 5.G User Guide
[x] Cancel search | Manufacturer: PORSCHE, Model Year: 2010, Model line: 911 GT3, Model: PORSCHE 911 GT3 2010 5.GPages: 251, PDF Size: 14.33 MB
Page 33 of 251

32
Operation, Safety Note 
The incident light in the area of the sensors must 
not be restricted, e.g. by stickers on the 
windshield. 
Switching off the automatic anti-glare 
operation 
fPress switch B.
Light-emitting diode C goes out. 
Switching on the automatic anti-glare 
operation 
fPress switch B.
Light-emitting diode C lights up. Warning!
Risk of injury. Electrolyte fluid can emerge 
from a broken mirror glass. 
This fluid irritates the skin and eyes. 
fIf the electrolyte fluid should come into contact 
with the eyes or skin, immediately rinse it off 
with clean water.
See a doctor if necessary.
Risk of damage to the paintwork, leather and 
plastic parts. Electrolyte fluid can be 
removed only while it is still wet. 
fClean the affected parts with water. The mirror heater is ready for operation when the 
ignition is on.
Switching on fPress button.
The light-emitting diode in the button lights up.
After approx. 15 minutes, the heater switches off 
automatically. 
The heater can be switched back on by pressing 
the button again.Switching off fPress button.
The light-emitting diode in the button goes out.
Rear Window Defogger, 
Door Mirror Heating
10_GT3_21.book  Seite 32  Donnerstag, 4. Juni 2009  12:48 12 
Page 38 of 251

Operation, Safety
37
Adjusting steering wheel height and 
longitudinal direction1. Insert ignition key fully into ignition lock.
2. Push the locking lever downwards.
3. Adjust steering wheel to fit the chosen 
backrest angle and your seat position by 
moving the steering wheel up or down and 
longitudinally.
4. Swivel locking lever back until you feel it 
engage. 
If necessary, move steering wheel slightly 
longitudinally.
Sun VisorsfSwing the sun visors down to prevent glare 
from the front. 
fTo prevent glare from the side, unclip the sun 
visor from the inner bracket and swivel round 
so that it is in front of the door window. Vanity mirror The vanity mirror on the rear of the sun visor is 
covered by a lid. 
 Warning!
Risk of injury in an accident.
fKeep the lid closed while driving.
Risk of damage.
fDo not force the lid beyond its end position.The vanity mirror illumination is switched on 
automatically when the cover is opened (arrow).
10_GT3_21.book  Seite 37  Donnerstag, 4. Juni 2009  12:48 12 
Page 43 of 251

42
Operation, Safety fAlways keep feet in the footwell while driving. 
Do not put feet on the dashboard or the seat 
area. Do not lean against the inside of the door 
or outside the window while the vehicle is 
moving.
fUsing accessories not approved by Porsche 
can cause the weight sensing system to be 
impaired. 
fDo not squeeze objects, such as the fire extin-
guisher, or first aid kit under the seat.
fOnly have seats removed and installed by an 
authorized Porsche dealer so that weight 
sensing components will not be damaged.
fGive your passenger all of the information in 
this chapter.
Note
Airbag components (e.g. steering wheel, door 
lining, seats) may be disassembled only by an 
authorized Porsche dealer.
When disposing of a used airbag unit, our safety 
instructions must be followed. These instructions 
can be obtained at any authorized Porsche dealer.
Function of the airbag systemAirbags are a supplemental safety system. Your 
primary protection comes from your safety belts.
The front airbags are triggered during a frontal 
collision of sufficient force and direction.
In the event of a side impact of corresponding force, the side airbag on the impact side is 
triggered.
The inflation process generates the amount of gas 
required to fill the airbags at the necessary 
pressure in fractions of a second.
Airbags help to protect the head and upper body, 
while simultaneously damping the motion of the 
driver and passenger in the impact direction in the 
event of a frontal impact or side impact.
In order to help provide protection in severe colli-
sions which can cause death and serious injury, 
airbags must inflate extremely rapidly. Such high 
speed inflation has a negative but unavoidable 
side effect, which is that it can and does cause 
injuries, including facial and arm abrasions, 
bruising and broken bones. You can help minimize 
such injuries by always wearing your safety belts.
There are many types of accidents in which 
airbags are not expected to deploy. These include 
accidents where the airbags whould provide no 
benefit, such as a rear impact against your 
vehicle. Other accidents where the airbags are 
designed not to deploy are those where the risk of 
injury from the airbag deployment could exeed any 
protective benefits, such as in low speed 
accidents or higher speed accidents where the 
vehicle decelerates over a longer time. Since 
airbag deployment does not occur in all accidents, 
this further emphasizes the need for you and your 
passenger to always wear safety belts.Your vehicle is equipped with a crash sensing and 
diagnostic module. This module will record the 
use of the seat belt restraint system by the driver 
and passenger when the airbags and/or belt tensi-
oner work.
Advanced AirbagYour vehicle is equipped with a weight sensing 
system for the passenger's seat in accordance 
with U.S. Federal Motor Vehicle Safety Standard 
208. 
Depending on the weight acting on the 
passenger's seat, the passenger's airbag will 
automatically be switched on and off.
Depending on the angle and force of impact, the 
passenger's airbag which is activated will be 
triggered during a collision.
Precondition for switching the passenger's airbag 
on and off, depending on weight:
– Vehicles equipped with key-operated airbag 
deactivation device:
Switch position AUTO.
– Ignition key is inserted.
Improper handling of the weight sensing 
system can unintentionally impair switching 
the passenger’s airbag off and on.
10_GT3_21.book  Seite 42  Donnerstag, 4. Juni 2009  12:48 12 
Page 44 of 251

Operation, Safety
43
Seat adjustment for the passenger's seat
 Danger!
Safety belts only offer protection when the 
backrest is upright and the belts are properly 
positioned on the body. Improperly positi-
oned safety belts can cause serious personal 
injury or death in an accident.
fDo not operate the car with the driver or 
passenger backrests excessively reclined.
fPorsche recommends the use of L.A.T.C.H. 
(Lower Anchorage and Tether for Children) 
equipped Porsche child seat.
Do not install a child restraint system in 
the Sports bucket seat.
The Sports bucket seat cannot be equipped with the LATCH system.
If the seat is in an extreme position (e.g., the 
backrest is in contact with the engine compart-
ment wall), the backrest can warp. Warping of the 
backrest can lead to malfunctions.
fCorrect the seat adjustment. 
Ensure that the seat is not jammed and is self-
supporting. 
Ensure that the backrest is in the upright 
position.fDo not transport a load and objects behind and 
under the passenger's seat. 
If the load or objects are under the seat, it can 
cause malfunctions.
If the weight on the passenger's seat is reduced 
significantly, e.g., by supporting weight on the 
armrest, the passenger's airbag can be switched 
off.
fSelect an upright seat position, and do not 
support weight on the armrests or lean out of 
the window. 
Always keep feet in the footwell while driving. 
Do not put feet on the dashboard or the seat 
area. Do not lean against the inside of the door 
or outside the window while the vehicle is 
moving.
If the passenger's seat is warped significantly, a 
message is displayed on the on-board computer:
fCorrect the seat adjustment.
fPlease see the chapter “WARNINGS ON THE 
INSTRUMENT PANEL AND THE ON-BOARD 
COMPUTER” on Page 148.
Vehicle modifications to accommodate 
persons with disabilities
Because modifications to your vehicle could 
compromise your advanced airbag system, 
please call 1-800-PORSCHE prior to having your 
vehicle modified.Automatic deactivation of the front 
passenger’s airbags
 Danger!
The use of a child restraint system in the 
passenger’s seat can result in serious 
personal injury or death to the child from an 
airbag deployment.
fPlease see the chapter “PASSENGER AIRBAG 
OFF INDICATOR LAMP DOES NOT LIGHT UP” 
on Page 44.
fBefore transporting a child on the passenger’s 
seat:
Please see the chapter “CHILD RESTRAINT 
SYSTEMS” on Page 47.
fDo not install a child restraint system in the Sports bucket seat. 
– When an up to one-year old child is seated 
in the child restraint system, the front airbag is 
automatically deactivated on the passenger’s 
side.
– When an adult is seated in the front seat, the 
front airbag remains active on the passenger‘s 
side.
10_GT3_21.book  Seite 43  Donnerstag, 4. Juni 2009  12:48 12 
Page 78 of 251

Operation, Safety
77
Rain sensorThe rain sensor on the windshield measures the 
amount of rainfall (snowfall too). Wiper speed is 
automatically adjusted accordingly.
Switching on
fMove wiper lever upwards to the first click.
Switching off
fMove wiper lever to position 0.
The rain sensor remains switched off if the wiper 
lever is already in position 1 when the ignition is 
switched on.To switch the rain sensor on again:
fMove wiper lever to position 0 and then to 
position 1 or
fOperate windshield washer system 5 or
fChange the sensitivity of the rain sensor with 
four-stage switch A.
Switch-on is confirmed by one wipe of the 
windshield.
On vehicles with the Sport Chrono Package Plus, 
further rain sensor functions can be selected via 
the PCM.
fPlease see the chapter “Individual Memory” in 
the separate PCM Owner’s Manual.
Changing the sensitivity of the rain sensor
Sensitivity can be set with switch A in 4 stages:
fAdjust switch A upwards – 
high sensitivity.
The setting is confirmed by one wipe of the 
windshield.
fAdjust switch A downwards – 
low sensitivity.Maintenance note
fPeriodically clean the wiper blades with a 
window cleaner, especially after the vehicle 
has been washed in a car wash. We recom-
mend Porsche window cleaner. If they are very 
dirty (e.g. with insect remains), they can be 
cleaned with a sponge or cloth.
If the wiper blades rub or squeak, this may be as 
a result of the following:
– If the vehicle is washed in an automatic car 
wash, wax residues may be adhering to the 
windshield. These wax residues can only be 
removed by using a window cleaner concen-
trate. 
fPlease see the chapter “WASHER FLUID” on 
Page 170.
fPlease contact your authorized Porsche dealer 
for further information.
– The wiper blades may be damaged or worn.
fReplace damaged wiper blades as soon as 
possible.
10_GT3_21.book  Seite 77  Donnerstag, 4. Juni 2009  12:48 12 
Page 85 of 251

84
Operation, Safety
Glove compartment
 Warning!
Risk of injury by the glove compartment lid in 
case of an accident. 
fKeep the glove compartment closed while driving. 
Opening 
fPull the catch and open the lid. 
Locking 
fLock the catch to secure the contents against 
unauthorized access.
CD holderOccupied drawers are indicated by a red window.
Opening drawers
fPush the button of the drawer you wish to 
open.
Closing drawers
fFold up CD drawer and close until it engages.Pen holderA pen can be clipped in on the right side of the CD 
holder.
10_GT3_21.book  Seite 84  Donnerstag, 4. Juni 2009  12:48 12 
Page 98 of 251

Automatic Air Conditioning System, Heated Rear Window/Door Mirror Heating
97 Automatic Air Conditioning System, Heated Rear Window/Door Mirror Heating
Automatic Air Conditioning System ................ 98
Central and Side Vents............................... 101
Fresh-air Intake .......................................... 101
Heated Rear Window/Door Mirror Heating .... 102
10_GT3_21.book  Seite 97  Donnerstag, 4. Juni 2009  12:48 12 
Page 99 of 251

98
Automatic air conditioning system, Heated rear window/Door mirror heating
Automatic Air Conditioning SystemThe automatic air-conditioning system controls 
the preselected interior temperature completely 
automatically. 
If necessary, the automatic system can be 
manually adjusted.
Automatic modefPress AUTO button G.
AUTO will appear on the display panel.
Air quantity and distribution are automatically 
controlled and variations are compensated.
All automatic setting functions can be individually 
changed. 
This setting is retained until the appropriate 
function button is pressed again or the AUTO 
button is pressed.
A- Defrosting the windshield
B- Heated rear window/door mirror heating
C-Temperature sensor
D- AC OFF button (air-conditioning compressor off/on)
E- Recirculating-air button
F- Temperature button
G- AUTO button (automatic mode)
H- Air distribution to footwell
I- Air distribution to central and side vents
J- Air distribution to windshield
K-Blower speed button
10_GT3_21.book  Seite 98  Donnerstag, 4. Juni 2009  12:48 12 
Page 100 of 251

Automatic air conditioning system, Heated rear window/Door mirror heating
99
Setting temperaturefPress button F upwards or downwards 
respectively.
To suit personal comfort, the interior temperature 
can be adjusted between 61 °F and 85 °F/16 °C 
and 29.5 °C. 
Recommendation: 72 °F/22 °C.
If “LO” or “HI” appears on the display, the system 
is operating at maximum cooling or heating 
power.
Automatic control is no longer active.
Note
If the preselected temperature is changed, the 
blower speed can increase automatically in 
automatic mode.
The desired temperature is reached more quickly 
this way.
Sensors
To avoid affecting the performance of the air-
conditioning system:
fDo not cover the sun sensor on the instrument 
panel or the temperature sensor C.fPress button A (switch on or off).
The windshield is defogged or defrosted as 
quickly as possible.
Air flows to the windshield only.
The light-emitting diode in the button lights up.
AC OFF – switching compressor for air-
conditioning system on and offThe air-conditioning compressor switches off 
automatically at temperatures below approx. 
37 °F/3 °C and cannot be switched on, even 
manually.
Whenever outside temperatures exceed approx. 
37 °F/3 °C, the air-conditioning compressor is 
always switched on in automatic mode.
The compressor can be switched off to save fuel, 
but control comfort is then limited:
fPress AC OFF button D.
The compressor is switched off.
The light-emitting diode in the button lights up.
fIf the interior temperature is too high, switch 
compressor back on or press AUTO button.
To dry incoming air in damp weather, do not 
switch off the air-conditioning compressor. 
This prevents fogging of windows.fPress button K upwards or downwards respec-
tively.
The preset blower speed is increased or decre-
ased.
The speed stages are indicated by a bar display.
If the button is pressed downwards at the lowest 
blower stage, the blower and automatic control 
are switched off. “OFF” will appear on the display 
field.
Pressing the button upwards or pressing the 
AUTO button switches the blower and automatic 
control back on again.
 Warning!
Risk of accident due to impaired vision, 
resulting in serious personal injury or death. 
In recirculating-air setting, the windows may 
fog up.
fOnly select recirculating-air setting for short 
periods.
fIf the windows fog up, switch recirculating-air 
setting off immediately by pressing the 
circulating-air button again and select the “Defrost windshield” function.
Defrosting the windshield
Adjusting blower speed
Recirculating-air setting
10_GT3_21.book  Seite 99  Donnerstag, 4. Juni 2009  12:48 12 
Page 101 of 251

100
Automatic air conditioning system, Heated rear window/Door mirror heating Switching recirculating-air setting on or off
fPress button E.
The outside-air supply is interrupted and only 
the inside air is circulated.
The light-emitting diode in the button lights up.
Over approx. 37 °F/3 °C
If the air-conditioning compressor was off, it 
switches on automatically. The duration of recircu-
lating-air setting is not limited.
Below approx. 37 °F/3 °C
The air-conditioning compressor is switched off. 
Recirculating-air setting is automatically ended 
after approx. 3 minutes.
Air distributionThe individual air distributions can be combined as 
desired.
Recommended setting in Summer:
Air distribution to central and side vents.
Recommended setting in Winter:
Air distribution to footwell and windshield.fPress button H.
The air flows to the footwell.
The selection appears on the display panel.
fPress button I.
The air flows from the central and side vents. 
Vents must be open.
The selection appears on the display panel.
fPress button J.
The air flows to the windshield.
The selection appears on the display panel.
Note on operation
fOn vehicles with the Sport Chrono Package 
Plus, individual air conditioning settings can be 
stored on your vehicle key.
Please see the chapter “Individual Memory” in 
the separate PCM Owner’s Manual.
General instructions for air-conditioning 
compressor– Can switch off briefly if engine is under an 
extreme load to ensure sufficient engine 
cooling.
– Switches off automatically at temperatures 
below approx. 37 °F/3 °C and cannot be 
switched on, even manually.
– Operates most effectively with windows 
closed.
If the car has been in the sun for a long time, it 
is a good idea to ventilate the interior briefly 
with the windows open.
– Depending on the outside temperature and 
humidity, condensation can drip from the 
evaporator and form a pool under the vehicle.
This is normal and not a sign of leakage.
– If uncooled air flows out when the lowest 
temperature has been set, switch off the air-
conditioning compressor and have the fault 
repaired at an authorized Porsche dealer. Air distribution to footwell
Air distribution to central and side 
vents
Air distribution to windshield
10_GT3_21.book  Seite 100  Donnerstag, 4. Juni 2009  12:48 12