sensor PORSCHE 911 TURBO 2014 6.G User Guide
[x] Cancel search | Manufacturer: PORSCHE, Model Year: 2014, Model line: 911 TURBO, Model: PORSCHE 911 TURBO 2014 6.GPages: 300, PDF Size: 10.61 MB
Page 89 of 300
Lights, Turn Signals and Windshield Wipers 87
Rain sensor operation, windshield wipers
In rain sensor mode, the amount of rain on the windshield is measured. The wipe interval is automatically controlled accordingly.
Rain sensor operation is activated automatically at speeds of less than approx. 2.5 mph (4 km/h) when the windshield wipers are switched on.
If a speed of approx. 5 mph (8 km/h) is exceeded, the system switches to the preselected wiper speed.
Information
fIf the wiper stalk is in position 1 when the ignition is switched on, the rain sensor is activated as soon as the vehicle speed exceeds approx. 2.5 mph (4 km/h).fIf the wiper stalk is in position 2 or 3 when the ignition is switched on, the windshield wipers remain switched off until the wiper stalk is actuated.
Information
The wiper is stopped when the luggage compartment lid is opened.
After closing the luggage compartment lid, the wiper stalk must be operated in order to switch the wiper back on.
Adjusting the rain sensor sensitivity
fMove switch A upwards – high sensitivity . The setting is confirmed by one wipe of the windshield.fMove switch A downwards – low sensitivity .
Activating and deactivating automatic rain sensor operation on the multi-function display
For information on automatic rain sensor operation:fPlease see the chapter “ACTIVATING AND DEACTIVATING RAIN SENSOR OPERATION” on page 121.
Headlight washer system
The washer sprays only while low beam or high beam is activated. fPress button B under the wiper stalk.
After every 10 wipes on the windshield, the headlights are cleaned automatically as well. The wipe count starts from zero again when the low beam is switched off.
14_991_Turbo_21.book Seite 87 Mittwoch, 9. April 2014 2:19 14
Page 123 of 300
Instrument Panel and Multi-Function Display 121
Adjusting brightness of orientation lighting
The brightness of the orientation lighting can be adapted individually.
Ambient lighting
The brightness of the ambient lighting can be adapted individually.
Setting interior lighting off delay
The off delay for the lighting in the passenger compartment after closing the vehicle doors can be adapted individually.
Setting activation of the rear wiper when reverse gear is engaged
You can configure the rear wiper to automatically perform a series of wipes when it is raining when reverse gear is engaged.
Available setting options: –“ Automatic” The rear wiper performs a series of wipes when reverse gear is engaged.–“ Manual” The rear wiper is not activated when reverse gear is engaged.
Activating and deactivating rain sensor operation
You can configure the windshield wiper to adjust its speed automatically when it is raining.
Available setting options: –“ Automatic” Wiper speed is adjusted automatically.–“ Manual” Wiper speed must be adjusted manually using the wiper stalk.
3. Confirm your selection.
Interior lights are activated.
Interior lights are deactivated.
1. Main menu “Vehicle” > “ Settings” > “ Light & Visibility” > “ Interior lights”
2.“Ambient light” and confirm.
3. Adjust to the desired brightness and confirm the setting.
1. Main menu “Vehicle” > “ Settings” > “ Light & Visibility” > “ Interior lights”
2.Select “Ambient light” and confirm.
3. Adjust to the desired brightness and confirm the setting.
1. Main menu “Vehicle” > “ Settings” > “ Light & Visibility” > “ Interior lights”
2.“Fade-out” and confirm.
3. Set desired off delay and confirm the setting.
1. Main menu “Vehicle” > “ Settings” > “ Light & Visibility” > “ Wiper”
2.“Rear wiper” and confirm.
3. Select the desired setting and confirm.
1. Main menu “Vehicle” > “ Settings” > “ Light & Visibility” > “ Wiper”
2.Select “Rain sensor” and confirm.
3. Select the desired setting and confirm.
14_991_Turbo_21.book Seite 121 Mittwoch, 9. April 2014 2:19 14
Page 139 of 300
Instrument Panel and Multi-Function Display 137
Tire change? Update settings The tire settings on the multi-function display must be updated after changing a wheel.
Tire pressure Reduce speed Speed too high for actual pressure. Inflate tire to the required pressure.
Comfort pressure Reduce speed Top speed for the preset comfort pressure exceeded.
Signal light switched on Driving light/side light on.
Parking light on Left/right parking light on.
Example: Check front left indicator The reported light is faulty. Check bulb.Have the fault corrected at an authorized Porsche dealer.
flashes
Adaptive headlight control defectiveService required
Have the fault corrected at an authorized Porsche dealer.
lights up
Driving light control defec- tiveService required
Have the fault corrected at an authorized Porsche dealer.
Headlight range regulation defectiveService required
Adjust your speed and driving style. Have the fault corrected at an authorized Porsche dealer.
High beam assistant not available Have the fault corrected at an authorized Porsche dealer.
Rain/light sensor defective Service required Switch on wipers/light manually. Have the fault corrected at an authorized Porsche dealer.
flashes
Headlight control defective Service required Have the fault corrected at an authorized Porsche dealer.
High beam assis unavailableOperate fullbeam manually
Have the fault corrected at an authorized Porsche dealer.
Light in instrument panel
Warning and information message on the multi-function display Meaning/Action required
14_991_Turbo_21.book Seite 137 Mittwoch, 9. April 2014 2:19 14
Page 140 of 300
138 Instrument Panel and Multi-Function Display
High beam assistant off No camera viewClean if necessary
Have the fault corrected at an authorized Porsche dealer.
PDLS+ currently restricted, no camera viewClean sensor?
PDLS+ temporarily unavailable due to camera fault.
PDLS+ fault Operate high beammanuallyService required
Have the fault corrected at an authorized Porsche dealer.
Assistance sys camera unavailableService required
Have the fault corrected at an authorized Porsche dealer.
Front view camera restrictedClean screen?
Assistance systems/camera temporarily unavailable due to weather conditions or dirt on the windscreen. Clean windshield if necessary.
Wiper defective Consult a workshop Have the fault corrected at an authorized Porsche dealer.
Example
Doors/lids open Close door/lid indicated.
Launch Control activatedLaunch Control is activated.
System fault Driving permittedConsult a workshop
One or more electrical systems may have failed. Adjust your speed and driving style.Have the fault corrected at an authorized Porsche dealer.
Instrument cluster/ Front Park Assistaudio faultService required
Turn signals tones, acoustic warnings and distance signals (e.g. for ParkAssist) are not available. Please remember this, e.g. when parking. Have the fault corrected at an authorized Porsche dealer.
Parking Assistant audio faultServicerequired
Acoustic warning and distance signals for ParkAssist are not available. Please remember this, e.g. when parking. Have the fault corrected at an authorized Porsche dealer.
Fault ParkAssist Have the fault corrected at an authorized Porsche dealer.
Light in instrument panel
Warning and information message on the multi-function display Meaning/Action required
14_991_Turbo_21.book Seite 138 Mittwoch, 9. April 2014 2:19 14
Page 141 of 300
Instrument Panel and Multi-Function Display 139
Distance Please brake Insufficient distance from vehicle in front.
ACC/PAS unavailable Service required Adaptive cruise control (ACC): Sensor at the front of the vehicle may be adversely affected by dirt, snow, ice or adverse weather conditions. Adjust your speed and driving style. Have the adaptive cruise control (ACC) or Porsche “Active Safe” fault rectified at an authorized Porsche dealer.
Limit 1/2 exceeded Selected speed limit 1 or 2 exceeded.
Warning light on the coolant temperature gauge flashes
Fault of the engine controlsystem
Have the fault corrected at an authorized Porsche dealer.
Outside temp. display defectiveService required
Have the fault corrected at an authorized Porsche dealer.
Aerodynamic rear spoilerClose sunroof
Close the sunroof.
Close sunroof completely
Decrease speedMove roof cover to end position
Open or close convertible top fully.
Top is opening/closing Message goes out in limit position.
Roof cover in service positionCar not ready
Roof control faultService required Have the fault corrected at an authorized Porsche dealer.
Place down wind deflector Message goes out in limit position.
Light in instrument panel
Warning and information message on the multi-function display Meaning/Action required
14_991_Turbo_21.book Seite 139 Mittwoch, 9. April 2014 2:19 14
Page 160 of 300
158 Driving and Driving Safety
Radar sensor
Adaptive cruise control uses a radar sensor located in the center of the front apron ( arrow).
Information
fAlways keep the radar sensor clean and free of ice and snow to ensure that it is fully functional.
For car care instructions:fPlease see the chapter “CAR CARE INSTRUCTIONS” on page 231.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 8 in. (20 cm) between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Radar sensor vision can be impaired by rain, snow, ice or heavy spray. Vehicles in front will not be detected properly or may not be detected at all.fDo not use adaptive cruise control under these conditions.
Warning message
Adaptive cruise control can be deactivated automatically if the radar sensor is very dirty or is covered in ice or by an obstacle, in unfavorable weather conditions (heavy rain) or when driving through tunnels.The message “ ACC/PAS unavailable Service required ” will appear on the multi-function display in the instrument panel.
For information on warning messages on the multi- function display:fPlease see the chapter “OVERVIEW OF WARNING AND INFORMATION MESSAGES” on page 129.
Information
This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada.Operation is subject to the following two condi-tions:1. This device may not cause harmful interfe- rence, and2. this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications made to this equipment not expressly approved by Porsche may void the FCC authorization to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communica-tions. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.– This Class A digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Radiofrequency Radiation Exposure
Weather Impairment of Radar Sensor
WARNINGh
WARNINGh
14_991_Turbo_21.book Seite 158 Mittwoch, 9. April 2014 2:19 14
Page 167 of 300
Driving and Driving Safety 165
–“ACC not possible Switch on PSM” Adaptive cruise control is not available because PSM was switched off.For information on Porsche Stability Management (PSM) :fPLEASE SEE THE CHAPTER “PORSCHE STABILITY MANAGEMENT (PSM)” on page 181.–“ ACC off” Adaptive cruise control was deactivated.– “ACC not possible Steering lock too large” The steering is turned too far.
General information
“Sport” and “Sport Plus” Mode
Adaptive cruise control regulates your driving more dynamically in “ Sport” and “Sport Plus” mode.
Exceptions for adaptive cruise control
Adaptive cruise control is not available in the following situations:– If the ignition is switched off.– When PSM is off.– If the driver’s door is opened and the driver’s safety belt is not fastened.– When parking or maneuvering in very tight spaces.– When the electric parking brake is activated.– If the PDK selector lever is in position N , R or P. – On upward or downward slopes of more than 15 %.
If one of these exception situations occurs when adaptive cruise control is switched on, adaptive cruise control will be switched off.A message to this effect appears on the multi-function display.
Warning messages
Overtake request when adaptive cruise control is active (ACC active)
If adaptive cruise control detects that braking assistance is required on the part of the driver, a warning signal sounds and the warning message “ Distance Please brake” appears on the multi- function display.
In this case, the braking power of the adaptive cruise control is not sufficient to prevent a collision.fBrake immediately.
Traffic situations in which vehicles cannot be reliably detected
The radar sensor for adaptive cruise control scans a narrow, cone-shaped area in front of your vehicle.Detection can be limited or unreliable, depending on the traffic situation and the size of the vehicle in front. The system may brake too late or unexpectedly.Stationary vehicles are not detected. The system cannot respond to stationary vehicles.fDrive with extreme care.fSlow down if necessary.
Inadequate braking power during automatic braking by the adaptive cruise control.
WARNINGh
14_991_Turbo_21.book Seite 165 Mittwoch, 9. April 2014 2:19 14
Page 168 of 300
166 Driving and Driving Safety
A – Vehicles changing lanes/cutting in
If a vehicle is changing lanes or cutting in ahead of you in the same lane, the vehicle will only be detected when it has moved completely into your lane.
B – Vehicles with a small cross-section/ narrow vehicles
Narrow or small vehicles will not be detected or will be detected too late.
C – Driving into and out of corners
When driving into and out of corners, vehicles will not be detected or will be detected too late, or adaptive cruise control will react to vehicles in adjacent lanes.
D – Stationary vehicles
A stationary vehicle that appears suddenly in the detection field of the radar sensor, e.g. after a vehicle in front changes lanes, will not be detected by adaptive cruise control.
Stationary vehicles are not detected by the radar sensor of the adaptive cruise control.fDrive with extreme care.fSlow down if necessary.
E – Vehicles with large overhangs
The tail of the vehicle will not be detected correctly on vehicles with large overhangs,e.g. timber lorries.
If there is a vehicle in front with a long overhang, the radar sensor of the adaptive cruise control is not able to detect the end of the vehicle or detects it incorrectly.fDrive with extreme care.fSlow down if necessary.Stationary vehicle not detected.WARNINGh
End of vehicle in front not detected correctly.WARNINGh
14_991_Turbo_21.book Seite 166 Mittwoch, 9. April 2014 2:19 14
Page 169 of 300
Driving and Driving Safety 167
Active Safety – Porsche “Active Safe”
The adaptive cruise control sensor is used for the Porsche “Active Safe” functions.
These include: – Brake system prefilling Prefilling of the brake system if the radar sensor detects that the vehicle is coming critically close to a moving obstacle in order to bridge the air gaps and improve braking response.– Brake Assist Reduction of the activation threshold of the Brake Assist function if the sensor detects that the vehicle is coming critically close to a moving obstacle.The activation threshold of the Brake Assist function is reduced in three stages, depending on how critical the danger situation is.– Target braking If the radar sensor detects that the vehicle is coming critically close to a moving obstacle and, at the same time, braking power is inadequate, brake pressure can be increased in accordance with the situation, through to full braking if required.
Information
All Porsche “Active Safe” functions are active for speeds of more than 20 mph (30 km/h).
Latent warning (visual)
If the vehicle is driving too close to the vehicle in front for a long time, to avoid a collision if the vehicle in front brakes, a latent warning appears on the multi-function display to warn the driver.fStay further back from the vehicle in front if necessary.
Prewarning (acoustic and visual)
If the radar sensor detects that the vehicle is coming critically close to and is very likely to collide with a moving obstacle in front, an acoustic and visual prewarning is issued. This warns the driver and still allows a collision to be prevented if the driver reacts accordingly.
Risk of collision with the vehicle in front.fBrake immediately.
Insufficient distanceWARNINGh
14_991_Turbo_21.book Seite 167 Mittwoch, 9. April 2014 2:19 14
Page 183 of 300
Driving and Driving Safety 181
Porsche Stability Management
(PSM)
PSM is an active control system for stabilization of the vehicle during extreme driving maneuvers.
PSM makes use of both the automatic brake differential (ABD) and anti-slip regulation (ASR) systems, as well as the functions of the anti-lock brake system (ABS) and engine drag torque control system (MSR).
In spite of the advantages of PSM, it is still the driver’s responsibility to adapt his driving style and maneuvers in line with road and weather conditions, as well as the traffic situation.
The increased safety that is provided should not induce you to take greater risks with your safety. The limits set by the physics of driving cannot be overcome, even with PSM.Risk of accidents due to inappropriate speed cannot be reduced by PSM.
Advantages of PSM
– Best possible traction and lane-holding ability in all driving situations – even on road surfaces with varying friction.– The system compensates for undesired vehicle reactions (Ferraria effect) when the driver releases the accelerator pedal or brakes on bends. This compensation functions up to the maximum lateral acceleration.– PSM actively helps to stabilize the vehicle if necessary during dynamic driving maneuvers (e.g. rapid steering movements, during lane changes, or on alternating bends).
– Improved braking stability on bends and on different or varying road surfaces.– Improved brake function and shorter stopping distance in the event of emergency braking.
Readiness for operation
PSM is switched on automatically every time you start the engine.
Function
Sensors at the wheels, brakes, steering system and engine continuously measure:– Speed– Direction of travel (steering angle)– Lateral acceleration– Axial acceleration– Rate of turn about the vertical axis
PSM uses these values to determine the direction of travel desired by the driver.PSM intervenes and corrects the course if the actual direction of motion deviates from the desired course (steering-wheel position):It brakes individual wheels as required. If necessary, PSM also influences the engine power or the gear-changing characteristic of Porsche Doppelkupplung (PDK) in order to stabilize the vehicle.
The events below inform the driver of PSM control operations and warn him to adapt his driving style to the road conditions:– PSM warning light on the instrument panel flashes.– Hydraulic noises can be heard.– The vehicle decelerates and steering-wheel forces are altered as PSM controls the brakes.– Reduced engine power.– The brake pedal pulsates and its position is changed during braking.In order to achieve full vehicle deceleration, foot pressure must be increased after the brake pedal has begun vibrating.
Examples of PSM control operations
– If the “front wheels of the vehicle drift” on a bend, the engine power is reduced and the rear wheel on the inside of the bend is braked if necessary.– If the rear of the vehicle swings out on a bend, the front wheel on the outside of the bend is braked.– Brake system prefilling:The brake system is prepared for possible subsequent emergency braking if the accelerator pedal is released suddenly and quickly. The brake system is prefilled and the brake pads are already applied gently to the brake disks.– Brake booster (Hydraulic Brake Assist):In the event of an emergency braking operation where the pedal force is insufficient, a brake booster provides the braking pressure necessary for maximum deceleration at all 4 wheels.
Loss of control over the vehicleWARNINGh
14_991_Turbo_21.book Seite 181 Mittwoch, 9. April 2014 2:19 14