homelink Ram 1500 2019 Owner's Manual
[x] Cancel search | Manufacturer: RAM, Model Year: 2019, Model line: 1500, Model: Ram 1500 2019Pages: 698, PDF Size: 9.04 MB
Page 18 of 698
▫To Close The Hood......................107
TAILGATE ............................ .108
▫ Opening ............................ .108
▫ Closing ............................. .108
GARAGE DOOR OPENER — IF EQUIPPED . . . .109
▫ Before You Begin Programming HomeLink .....110
▫ Canadian/Gate Operator Programming .......112
▫ Using HomeLink .......................114
▫ Security ..............................114
▫ Troubleshooting Tips ....................114
▫ General Information .....................114
INTERNAL EQUIPMENT ..................115
▫ Storage ..............................115
▫ Cupholders ......................... .125
▫ Electrical Power Outlets ..................127 ▫
Power Inverter — If Equipped .............130
▫ Wireless Charging Pad — If Equipped .......133
▫ Overhead Sunglass Storage ...............134
PICKUP BOX .......................... .134
RAMBOX — IF EQUIPPED .................135
▫ RamBox Integrated Box Side Storage Bins ......136
▫ RamBox Safety Warning ..................138
▫ Bed Extender — If Equipped ...............139
▫ Bed Rail Tie-Down System ................145
SLIDE-IN CAMPERS .....................147
▫ Camper Applications ....................147
EASY-OFF TAILGATE ....................147
▫ Disconnecting The Rear Camera And Remote
Keyless Entry ......................... .148
▫ Removing
The Tailgate ...................149
▫ Locking Tailgate ....................... .150
16 GETTING TO KNOW YOUR VEHICLE
Page 111 of 698
GARAGE DOOR OPENER — IF EQUIPPED
HomeLink replaces up to three hand-held transmitters that
operate devices such as garage door openers, motorized
gates, lighting or home security systems. The HomeLink
unit is powered by your vehicles 12 Volt battery.
The HomeLink buttons that are located on the sun visor
designate the three different HomeLink channels.
NOTE:HomeLink is disabled when the Vehicle Security
Alarm is active.
WARNING!
• Your motorized door or gate will open and close
while you are programming the universal trans-
ceiver. Do not program the transceiver if people, pets
or other objects are in the path of the door or gate.
Only use this transceiver with a garage door opener
that has a “stop and reverse” feature as required by
Federal safety standards. This includes most garage
door opener models manufactured after 1982. Do not
use a garage door opener without these safety fea-
tures.
• Vehicle exhaust contains carbon monoxide, a danger-
ous gas. Do not run your vehicle in the garage while
programming the transceiver. Exhaust gas can cause
serious injury or death.
NOTE: Only use this transceiver with a garage door
opener that has a “stop and reverse” feature as required by
federal safety standards. This includes most garage door
opener models manufactured after 1982. Do not use a
garage door opener without these safety features. Call
toll-free 1-800-355-3515 or, on the Internet at
HomeLink.com for safety information or assistance.
HomeLink Buttons
3
GETTING TO KNOW YOUR VEHICLE 109
Page 112 of 698
Before You Begin Programming HomeLink
Be sure that your vehicle is parked outside of the garage
before you begin programming.
For more efficient programming and accurate transmission
of the radio-frequency signal it is recommended that a new
battery be placed in the hand-held transmitter of the device
that is being programmed to the HomeLink system.
To erase the channels, place the ignition in the ON/RUN
position, and push and hold the two outside HomeLink
buttons (I and III) for up to 20 seconds or until the orange
indicator flashes.
NOTE:
•Erasing all channels should only be performed when
programming HomeLink for the first time. Do not erase
channels when programming additional buttons.
• If you have any problems, or require assistance, please
call toll-free 1-800-355-3515 or, on the Internet at
HomeLink.com for information or assistance.
Programming A Rolling Code
For programming garage door openers that were manufac-
tured after 1995. These garage door openers can be identi-
fied by the “LEARN” or “TRAIN” button located where
the hanging antenna is attached to the garage door opener.
NOTE: It is NOT the button that is normally used to open
and close the door. The name and color of the button may
vary by manufacturer.
Training The Garage Door Opener
1 — Door Opener
2 — Training Button
110 GETTING TO KNOW YOUR VEHICLE
Page 113 of 698
1. Place the ignition in the ON/RUN position.
2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm)away from the HomeLink button you wish to program
while keeping the HomeLink indicator light in view.
3. Push and hold the HomeLink button you want to program while you push and hold the hand-held trans-
mitter button.
4. Continue to hold both buttons and observe the indicator light. The HomeLink indicator will flash slowly and
then rapidly after HomeLink has received the frequency
signal from the hand-held transmitter. Release both
buttons after the indicator light changes from slow to
rapid.
5. At the garage door opener motor (in the garage), locate the “LEARN” or “TRAINING” button. This can usually
be found where the hanging antenna wire is attached to
the garage door opener/device motor. Firmly push and
release the “LEARN” or “TRAINING” button. On some
garage door openers/devices there may be a light that
blinks when the garage door opener/device is in the
LEARN/TRAIN mode.
NOTE: You have 30 seconds in which to initiate the next
step after the LEARN button has been pushed. 6. Return to the vehicle and push the programmed
HomeLink button twice (holding the button for two
seconds each time). If the garage door opener/device
activates, programming is complete.
NOTE: If the garage door opener/device does not activate,
push the button a third time (for two seconds) to complete
the training.
To program the remaining two HomeLink buttons, repeat
each step for each remaining button. DO NOT erase the
channels.
Reprogramming A Single HomeLink Button (Rolling
Code)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
2. Push and hold the desired HomeLink button until the indicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button proceed with “Program- ming A Rolling Code” step 2 and follow all remaining
steps.
3
GETTING TO KNOW YOUR VEHICLE 111
Page 114 of 698
Programming A Non-Rolling Code
For programming Garage Door Openers manufactured
before 1995.
1. Cycle the ignition to the ON/RUN position.
2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm)away from the HomeLink button you wish to program
while keeping the HomeLink indicator light in view.
3. Press and hold the HomeLink button you want to program while you press and hold the hand-held trans-
mitter button.
4. Continue to hold both buttons and observe the indicator light. The HomeLink indicator will flash slowly and
then rapidly after HomeLink has received the frequency
signal from the hand-held transmitter. Release both
buttons after the indicator light changes from slow to
rapid.
5. Press and hold the programmed HomeLink button and observe the indicator light.
• If the indicator light stays on constantly, programming
is complete and the garage door/device should acti-
vate when the HomeLink button is pressed. •
To program the two remaining HomeLink buttons,
repeat each step for each remaining button. DO NOT
erase the channels.
Reprogramming A Single HomeLink Button (Non-
Rolling Code)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
2. Press and hold the desired HomeLink button until the indicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button, proceed with “Program- ming A Non-Rolling Code” step 2 and follow all remain-
ing steps.
Canadian/Gate Operator Programming
For programming transmitters in Canada/United States
that require the transmitter signals to “time-out” after
several seconds of transmission.
Canadian radio frequency laws require transmitter signals
to time-out (or quit) after several seconds of transmission –
which may not be long enough for HomeLink to pick up
112 GETTING TO KNOW YOUR VEHICLE
Page 115 of 698
the signal during programming. Similar to this Canadian
law, some U.S. gate operators are designed to time-out in
the same manner.
It may be helpful to unplug the device during the cycling
process to prevent possible overheating of the garage door
or gate motor.
1. Cycle the ignition to the ON/RUN position.
2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm)away from the HomeLink button you wish to program
while keeping the HomeLink indicator light in view.
3. Continue to press and hold the HomeLink button, while you press and release (“cycle”) your hand-held trans-
mitter every two seconds until HomeLink has success-
fully accepted the frequency signal. The indicator light
will flash slowly and then rapidly when fully trained.
4. Watch for the HomeLink indicator to change flash rates. When it changes, it is programmed. It may take up to 30
seconds or longer in rare cases. The garage door may
open and close while you are programming.
5. Press and hold the programmed HomeLink button and observe the indicator light. NOTE:
•If the indicator light stays on constantly, programming
is complete and the garage door/device should acti-
vate when the HomeLink button is pressed.
• To program the two remaining HomeLink buttons,
repeat each step for each remaining button. DO NOT
erase the channels.
If you unplugged the garage door opener/device for
programming, plug it back in at this time.
Reprogramming A Single HomeLink Button (Canadian/
Gate Operator)
To reprogram a channel that has been previously trained,
follow these steps:
1. Cycle the ignition to the ON/RUN position.
2. Press and hold the desired HomeLink button until the indicator light begins to flash after 20 seconds. Do not
release the button.
3. Without releasing the button, proceed with “Canadian/ Gate Operator Programming” step 2 and follow all
remaining steps.
3
GETTING TO KNOW YOUR VEHICLE 113
Page 116 of 698
Using HomeLink
To operate, push and release the programmed HomeLink
button. Activation will now occur for the programmed
device (i.e. garage door opener, gate operator, security
system, entry door lock, home/office lighting, etc.) The
hand-held transmitter of the device may also be used at
any time.
Security
It is advised to erase all channels before you sell or turn in
your vehicle.
To do this, push and hold the two outside buttons for 20
seconds until the orange indicator flashes. Note that all
channels will be erased. Individual channels cannot be
erased.
The HomeLink Universal Transceiver is disabled when the
Vehicle Security Alarm is active.
Troubleshooting Tips
If you are having trouble programming HomeLink, here
are some of the most common solutions:
•Replace the battery in the Garage Door Opener hand-
held transmitter. •
Push the LEARN button on the Garage Door Opener to
complete the training for a Rolling Code.
• Did you unplug the device for programming and re-
member to plug it back in?
If you have any problems, or require assistance, please call
toll-free 1-800-355-3515 or, on the Internet at
HomeLink.com for information or assistance.
General Information
The following regulatory statement applies to all Radio
Frequency (RF) devices equipped in this vehicle:
This device complies with Part 15 of the FCC Rules and
with Innovation, Science and Economic Development
Canada license-exempt RSS standard(s). Operation is sub-
ject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, in- cluding interference that may cause undesired opera-
tion.
NOTE: Changes or modifications not expressly approved
by the party responsible for compliance could void the
user ’s authority to operate the equipment.
114 GETTING TO KNOW YOUR VEHICLE
Page 686 of 698
Engine Oil Viscosity........................ .499
Engine Oil Viscosity Chart ....................499
Enhanced Accident Response Feature .........260, 484
Entry System, Illuminated .....................76
Ethanol ................................. .560
Exhaust Gas Cautions ....................285, 562
Exhaust System ........................ .285, 511
Exterior Lighting ............................68
Exterior Lights ......................... .68, 287
Filters Air Cleaner ............................ .501
Air Conditioning ..................... .95, 504
Engine Oil ......................... .501, 564
Engine Oil Disposal ...................... .500
Flashers Turn Signals ..................... .73, 192, 287
Flash-To-Pass ..............................71
Flat Tire Stowage .......................... .470
Fluid, Brake ............................. .566
Fluid Capacities ........................... .563
Fluid Leaks .............................. .288
Fluid Level Checks Brake ................................ .519
Fluids And Lubricants ...................... .564Fog Lights
............................ .72, 446
Fold-Flat Seats .............................43
Forward Collision Warning ....................221
Four-Way Hazard Flasher .....................435
Four Wheel Drive ......................... .313
Freeing A Stuck Vehicle ..................... .480
Front Axle (Differential) ..................... .521
Fuel ................................... .558
Adding .............................. .404
Additives ............................. .559
Clean Air ............................. .559
Ethanol .............................. .560
Gasoline .............................. .558
Light ................................ .186
Materials
Added........................ .559
Methanol ............................. .560
Octane Rating ....................558, 559, 564
Requirements ....................... .558, 563
Tank Capacity .......................... .563
Fuses .................................. .449
Garage Door Opener (HomeLink) ...............109
Gasoline, Clean Air ........................ .559
Gasoline, Reformulated ..................... .559
General Information ........................ .231
684 INDEX
Page 687 of 698
Glass Cleaning........................... .553
Grocery Bag Retainer .........................55
Gross Axle Weight Rating .....................408
Gross Vehicle Weight Rating ...................408
Guide Body Builders ............................5
GVWR ................................. .406
Hazard Driving Through Flowing, Rising, Or Shallow
Standing Water ......................... .430
Hazard Warning Flashers .....................435
Headlights .............................. .442
Cleaning .............................. .547
High Beam ..............................69
High Beam/Low Beam Select Switch ...........69
Passing ................................71
Switch .................................68
Head Restraints ............................55
Head Rests ................................55
Heated Mirrors .............................66
Heater, Engine Block ....................... .299
High Beam/Low Beam Select (Dimmer) Switch ......69
Hill Descent Control ....................... .208
Hill Descent Control Indicator .................208Hill Start Assist
........................... .200
Hitches Trailer Towing .......................... .413
Hoisting ................................ .522
HomeLink (Garage Door Opener) ...............109
Hood Prop .............................. .106
Hood Release ............................ .106
Ignition ..................................27
Switch .................................27
Illuminated Entry ...........................76
Inside Rearview Mirror ....................61, 436
Instrument Cluster Descriptions ........................... .192
Display .............................. .167
Instrument Panel Lens Cleaning ................552
Integrated Trailer Brake Control ................417
Interior Appearance Care .....................550
Interior Lights ..............................74
Intermittent Wipers (Delay Wipers) ...............
77
Introduction ................................4
In Vehicle Help Vehicle User Guide ........................18
Inverter Outlet (115V) ...................... .13012
INDEX 685
Page 695 of 698
Tips ..................................422
Trailer And Tongue Weight ..................414
Wiring ............................... .420
Trailer Towing Guide ....................... .414
Trailer Weight ............................ .414
Transfer Case ............................ .522
Electronically Shifted ...................314, 318
Fluid ................................ .566
Transmission ............................. .306
Automatic ......................... .306, 520
Fluid ................................ .566
Maintenance ........................... .520
Shifting .............................. .304
Transporting Pets ......................... .284
Tread Wear Indicators ...................... .536
Turn Signals .....................73, 192, 442, 447
Uconnect Uconnect Settings . . . .572, 580, 582, 604, 607, 628, 630
Uconnect Settings Customer Programmable
Features ............38, 580, 582, 604, 607, 628, 630
Passive Entry Programming ........38, 580, 604, 628
Uconnect Voice Command ....................648
Uniform Tire Quality Grades ..................545 Universal Garage Door Opener (HomeLink)
........109
Universal Transmitter ....................... .109
Unleaded Gasoline ........................ .558
Untwisting Procedure, Seat Belt ................238
USB................................... .642
Utility Rails, Rear Cargo Area ..................145
Vehicle Identification Number (VIN) .............556
Vehicle Loading ....................... .406, 529
Vehicle Modifications/Alterations .................6
Vehicle Storage ......................... .94, 546
Vehicle User Guide In Vehicle Help ...........................18
Navigation ..............................18
Operating Instructions ......................18
Searching User Guide ......................18
Viscosity, Engine Oil ....................... .499
V
oice Recognition System (VR) .................648
Warning Lights (Instrument Cluster Descriptions) . . . .185
Warnings And Cautions .......................5
Warranty Information ...................... .677
Washers, Windshield ..................... .77, 497
Washing Vehicle .......................... .548
12
INDEX 693