engine Ram 3500 2017 Workshop Manual

STARTING AND OPERATING
CONTENTS
STARTING PROCEDURES .................381
▫ Normal Starting ....................... .381
▫ Automatic Transmission ..................382
▫ Keyless Enter-N-Go — Ignition .............382
▫ Normal Starting ....................... .382
▫ Extreme Cold Weather
(Below –22°F Or 30°C) ..................384
▫ If Engine Fails To Start ..................384
▫ After Starting ......................... .385
 ENGINE BLOCK HEATER — IF EQUIPPED . . . .385
 AUTOMATIC TRANSMISSION ..............386
▫ Key Ignition Park Interlock ................387
▫ Brake/Transmission Shift Interlock System . . . .387 ▫
Eight-Speed Automatic Transmission —
If Equipped ......................... .388
▫ Six-Speed Automatic Transmission —
1500 Models Only (If Equipped) ............395
▫ Six-Speed Automatic Transmission —
2500/3500 Models Only ..................405
 FOUR-WHEEL DRIVE OPERATION —
IF EQUIPPED ......................... .414
▫ Manually Shifted Transfer Case —
If Equipped .......................... .414
▫ Electronically Shifted Transfer Case
(Four-Position Switch) — If Equipped ........417
▫ Electronically Shifted Transfer Case
(Five-Position Switch) — If Equipped ........422
▫ Four-Position Electronically Shifted Transfer
Case (Eight Speed Transmission Only) —
If Equipped ......................... .427
5

DRIVING ON SLIPPERY SURFACES ..........471
▫ Acceleration .......................... .471
▫ Traction ............................. .471
 DRIVING THROUGH WATER ..............472
▫ Flowing/Rising Water ...................472
▫ Shallow Standing Water ..................472
 OFF-ROAD DRIVING TIPS .................473
▫ After Driving Off-Road ...................474
 WINCH USAGE — POWER WAGON ONLY
(IF EQUIPPED) ........................ .474
▫ Things To Know Before Using Your Winch .....474
▫ Understanding The Features Of Your Winch . . . .476
▫ Winch Accessories ..................... .478
▫ Operating Your Winch ...................479
▫ Rigging Techniques .....................489
 POWER STEERING ...................... .490
▫ Electric Power Steering — 1500 Models .......490▫
Hydraulic Power Steering —
2500/3500 Models ..................... .491
 FUEL SAVER TECHNOLOGY 5.7L/6.4L ENGINES
ONLY — IF EQUIPPED ....................492
 PARKING BRAKE ...................... .492
 BRAKE SYSTEM ....................... .494
▫ Hydraulic Brake Assist — 2500/3500 Models Only
(Except Power Wagon) ...................494
 ELECTRONIC BRAKE CONTROL SYSTEM .....495
▫ Electronic Brake Force Distribution (EBD) ......495
▫ Brake System Warning Light ...............495
▫ Anti-Lock Brake System (ABS) .............495
▫ Anti-Lock

Brake Warning Light .............497
▫ Brake Assist System (BAS) ................497
▫ Hill Start Assist (HSA) ...................498
▫ Traction Control System (TCS) .............500
▫ Electronic Stability Control (ESC) ...........500
▫ Electronic Roll Mitigation (ERM) ...........504
5
STARTING AND OPERATING 377

▫Trailer Sway Control (TSC) — If Equipped . . . .504
▫ Hill Descent Control (HDC) — If Equipped . . . .505
 TIRE SAFETY INFORMATION ..............508
▫ Tire Markings ........................ .508
▫ Tire Identification Number (TIN) ............511
▫ Tire Terminology And Definitions ...........512
▫ Tire Loading And Tire Pressure ............513
 TIRES — GENERAL INFORMATION .........518
▫ Tire Pressure ......................... .518
▫ Tire Inflation Pressures ..................519
▫ Tire Pressures For High Speed Operation .....520
▫ Radial Ply Tires ....................... .520
▫ Tire Types ........................... .521
▫ Run Flat Tires — If Equipped ..............522
▫ Spare Tires — If Equipped ................523
▫ Tire Spinning ........................ .525
▫ Tread Wear Indicators ...................526 ▫
Life Of Tire .......................... .526
▫ Replacement Tires ..................... .527
 TIRE CHAINS (TRACTION DEVICES) .........528
 TIRE ROTATION RECOMMENDATIONS ......530
▫ Directional Tires — If Equipped .............531
▫ Dual Rear Wheels — If Equipped ...........532
 DEPARTMENT OF TRANSPORTATION
UNIFORM TIRE QUALITY GRADES ..........533
▫ Treadwear ........................... .533
▫ Traction Grades ....................... .534
▫ T

emperature Grades .....................534
 TIRE PRESSURE MONITOR SYSTEM (TPMS) . . .535
▫ Premium System ...................... .536
▫ Tire Pressure Information System (TPIS)
3500 Series Trucks ..................... .539
▫ General Information ....................540
 FUEL REQUIREMENTS ...................541
▫ 3.6L Engine .......................... .541
378 STARTING AND OPERATING

▫5.7L Engine .......................... .541
▫ 6.4L Engine .......................... .542
▫ Reformulated Gasoline ..................542
▫ Gasoline/Oxygenate Blends ...............542
▫ E-85 Usage In Non-Flex Fuel Vehicles .........543
▫ CNG And LP Fuel System Modifications ......543
▫ MMT In Gasoline ...................... .543
▫ Materials Added To Fuel .................544
▫ Fuel System Cautions ....................544
▫ Carbon Monoxide Warnings ...............545
 FLEXIBLE FUEL (3.6L ENGINE ONLY) —
IF EQUIPPED ......................... .545
▫ E-85 General Information .................545
▫ Ethanol Fuel (E-85) ..................... .546
▫ Fuel Requirements .....................546
▫ Selection Of Engine Oil For Flexible Fuel
Vehicles (E-85) And Gasoline Vehicles ........546▫
Starting ............................ .547
▫ Cruising Range ....................... .547
▫ Replacement Parts ..................... .547
▫ Maintenance ......................... .547
 ADDING FUEL ........................ .548
▫ Loose Fuel Filler Cap Message .............549
 VEHICLE LOADING .....................549
▫ Certification Label ..................... .549
 TRAILER TOWING ..................... .551
▫ Common Towing Definitions ...............551
▫ T

railer Hitch Type and Maximum
Trailer Weight ........................ .558
▫ Trailer Towing Weights (Maximum
Trailer Weight Ratings) ..................559
▫ Trailer And Tongue Weight ...............559
▫ Towing Requirements ...................559
▫ Towing Tips .......................... .567
5
STARTING AND OPERATING 379

STARTING PROCEDURES
Before starting your vehicle, adjust your seat, adjust both
inside and outside mirrors, and fasten your seat belt.
The starter should not be operated for more than 10-second
intervals. Waiting a few seconds between such intervals
will protect the starter from overheating.
WARNING!
•When leaving the vehicle, always make sure the
keyless ignition node is in the OFFmode, remove
the key fob from the vehicle and lock the vehicle.
• Never leave children alone in a vehicle, or with
access to an unlocked vehicle. Allowing children to
be in a vehicle unattended is dangerous for a number
of reasons. A child or others could be seriously or
fatally injured. Children should be warned not to
touch the parking brake, brake pedal or the gear
selector.
(Continued)
WARNING! (Continued)
•Do not leave the key fob in or near the vehicle, or in
a location accessible to children, and do not leave the
ignition of a vehicle equipped with Keyless Enter-
N-Go in the ACC or ON/RUN mode. A child could
operate power windows, other controls, or move the
vehicle.
• Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build-up may
cause serious injury or death.
Normal Starting
Normal starting of either a warm or cold engine is obtained
without pumping or pressing the accelerator pedal. Cycle
the ignition to the START position and release when the
engine starts. If the engine fails to start within 10 seconds,
cycle the ignition to the OFF position, wait five seconds,
then repeat the “Normal Starting” procedure.
5
STARTING AND OPERATING 381

Automatic Transmission
Start the engine with the transmission in PARK position.
Apply the brake before shifting into any driving range.
NOTE:
•This vehicle is equipped with a transmission shift inter-
locking system. The brake pedal must be pressed to shift
out of PARK.
• If equipped with an 8 speed transmission starting the
vehicle in NEUTRAL is not possible unless the Manual
Park Release has been activated. For the Manual Park
Release operation refer to Manual Park Release in “What
To Do In Emergencies”.
Tip Start Feature
Do not press the accelerator. Cycle the ignition switch
briefly to the START position and release it. The starter
motor will continue to run but will automatically disen-
gage when the engine is running.
Keyless Enter-N-Go — Ignition
This feature allows the driver to operate
the ignition switch with the push of a
button, as long as the Remote Start/
Keyless Enter-N-Go key fob is in the
passenger compartment.
Normal Starting
To Turn On The Engine Using The ENGINE
START/STOP Button
1. The transmission must be in PARK or NEUTRAL.
2. Press and hold the brake pedal while pushing the ENGINE START/STOP button once.
3. The system takes over and attempts to start the vehicle. If the vehicle fails to start, the starter will disengage
automatically after 10 seconds.
4. If you wish to stop the cranking of the engine prior to the engine starting, push the button again.
382 STARTING AND OPERATING

NOTE:Normal starting of either a cold or a warm engine
is obtained without pumping or pressing the accelerator
pedal.
To Turn Off The Engine Using ENGINE
START/STOP Button
1. Place the gear selector in PARK, then push and release the ENGINE START/STOP button.
2. The ignition switch will return to the OFF position.
3. If the gear selector is not in PARK, the ENGINE START/ STOP button must be held for two seconds or three short
pushes in a row with the vehicle speed above 5 mph
(8 km/h) before the engine will shut off. The ignition
switch position will remain in the ACC position until the
gear selector is in PARK and the button is pushed twice
to the OFF position. If the gear selector is not in PARK
and the ENGINE START/STOP button is pushed once,
the instrument cluster will display a “Vehicle Not In
Park” message and the engine will remain running.
Never leave a vehicle out of the PARK position, or it
could roll. NOTE:
If the ignition switch is left in the ACC or RUN
(engine not running) position and the transmission is in
PARK, the system will automatically time out after 30
minutes of inactivity and the ignition will switch to the
OFF position.Idle Shutdown — 6.4L Engine Only
This feature can be enabled so that the truck will automati-
cally shutdown when the truck has been idling for a set
period of time when the engine is at operating tempera-
ture. Idle time can be set in 5 minute increments between 5
and 60 minutes. See your local authorized dealer to enable
this feature.
NOTE: The idle shut down timer is disabled while the PTO
is active.5
STARTING AND OPERATING 383

ENGINE START/STOP Button Functions — With
Driver ’s Foot OFF The Brake Pedal (In PARK Or
NEUTRAL Position)
The ENGINE START/STOP button operates similar to an
ignition switch. It has three positions, OFF, ACC, RUN. To
change the ignition switch positions without starting the
vehicle and use the accessories follow these steps:
1. Starting with the ignition in the OFF position:
2. Push the ENGINE START/STOP button once to changethe ignition to the ACC position.
3. Push the ENGINE START/STOP button a second time to change the ignition to the RUN position.
4. Push the ENGINE START/STOP button a third time to return the ignition to the OFF position.
Extreme Cold Weather (Below –22°F Or 30°C)
To ensure reliable starting at these temperatures, use of an
externally powered electric engine block heater (available
from your authorized dealer) is recommended.
If Engine Fails To Start
If the engine fails to start after you have followed the
“Normal Starting” procedure, it may be flooded. Push the
accelerator pedal all the way to the floor and hold it there
while the engine is cranking. This should clear any excess
fuel in case the engine is flooded.
The starter motor will engage automatically, run for 10
seconds, and then disengage. Once this occurs, release the
accelerator pedal and the brake pedal, wait 10 to 15
seconds, then repeat the “Normal Starting” procedure.
CAUTION!
To prevent damage to the starter, do not crank the
engine for more than 10 seconds at a time. Wait 10 to 15
seconds before trying again.
WARNING!
•Never pour fuel or other flammable liquids into the
throttle body air inlet opening in an attempt to start
the vehicle. This could result in a flash fire causing
serious personal injury.
(Continued)
384 STARTING AND OPERATING

WARNING!(Continued)
•Do not attempt to push or tow your vehicle to get it
started. Vehicles equipped with an automatic trans-
mission cannot be started this way. Unburned fuel
could enter the catalytic converter and once the
engine has started, ignite and damage the converter
and vehicle.
• If the vehicle has a discharged battery, booster cables
may be used to obtain a start from a booster battery
or the battery in another vehicle. This type of start
can be dangerous if done improperly. Refer to
“Jump-Starting” in “What To Do In Emergencies” for
further information.
If the engine has been flooded, it may start to run, but not
have enough power to continue running when the ignition
button/key is released. If this occurs, continue cranking
with the accelerator pedal pushed all the way to the floor.
Release the accelerator pedal and the ignition button/key
once the engine is running smoothly.
If the engine shows no sign of starting after a 10 second
period of engine cranking with the accelerator pedal held
to the floor, wait 10 to 15 seconds, then repeat the “Normal
Starting” procedure.
After Starting
The idle speed is controlled automatically, and it will
decrease as the engine warms up.
ENGINE BLOCK HEATER — IF EQUIPPED
The engine block heater warms the engine, and permits
quicker starts in cold weather. Connect the cord to a
standard 110-115 Volt AC electrical outlet with a grounded,
three-wire extension cord.
1500 Models
The engine block heater cord is routed under the hood on
the passenger side of the vehicle near the right head lamp
assembly. It is located between the front grill and the
radiator, but underneath the black upper seal.
2500/3500 Models
The engine block heater cord is routed through the grille by
the right front tow hook.
It includes a removable cap that is secured by a tethered
strap. It also has a c-clip that is used for storage when not
in use for the winter months. During winter months,
remove the heater cord wiring assembly from itself on the
c-clip.
5
STARTING AND OPERATING 385

The engine block heater must be plugged in at least one
hour to have an adequate warming effect on the engine.
WARNING!
Remember to disconnect the engine block heater cord
before driving. Damage to the 110-115 Volt electrical
cord could cause electrocution.
AUTOMATIC TRANSMISSION
CAUTION!
Damage to the transmission may occur if the following
precautions are not observed:
•Shift into or out of PARK or REVERSE only after the
vehicle has come to a complete stop.
• Do not shift between PARK, REVERSE, NEUTRAL,
or DRIVE when the engine is above idle speed.
• Before shifting into any gear, make sure your foot is
firmly pressing the brake pedal.
NOTE: You must press and hold the brake pedal while
shifting out of PARK.
WARNING!
• It is dangerous to shift out of PARK or NEUTRAL if
the engine speed is higher than idle speed. If your
foot is not firmly pressing the brake pedal, the
vehicle could accelerate quickly forward or in re-
verse. You could lose control of the vehicle and hit
someone or something. Only shift into gear when the
engine is idling normally and your foot is firmly
pressing the brake pedal.
• Unintended movement of a vehicle could injure
those in or near the vehicle. As with all vehicles, you
should never exit a vehicle while the engine is
running. Before exiting a vehicle, always apply the
parking brake, shift the transmission into PARK,
turn the engine OFF, and remove the key fob. When
the ignition is in the LOCK/OFF (key removal)
position, (or, with Keyless Enter-N-Go, when the
ignition is in the OFF mode) the transmission is
locked in PARK, securing the vehicle against un-
wanted movement.
• When leaving the vehicle, always make sure the
ignition is in the OFF mode, remove the key fob from
the vehicle, and lock the vehicle.
(Continued)
386 STARTING AND OPERATING