engine oil RAM CHASSIS CAB 2019 Owner's Manual

416 SERVICING AND MAINTENANCE
Checking Oil Level — Gas Engine
To assure proper lubrication of your vehicle's engine, the
engine oil must be maintained at the correct level. Check the
oil level at regular intervals, such as every fuel stop. The best
time to check the engine oil level is about five minutes after
a fully warmed up engine is shut off.
Checking the oil while the vehicle is on level ground will
improve the accuracy of the oil level readings. Always main -
tain the oil level within the SAFE zone on the dipstick.
Adding one quart of oil when the reading is at the bottom of
the SAFE zone will result in a reading at the top of the safe
zone on these engines.
Adding Washer Fluid
The fluid reservoir is located under the hood and should be
checked for fluid level at regular intervals. Fill the reservoir
with windshield washer solvent only (not radiator anti -
freeze). When refilling the washer fluid reservoir, take some washer fluid and apply it to a cloth or towel and wipe the
wiper blades clean. This will help blade performance.
To prevent freeze-up of your windshield washer system in
cold weather, select a solution or mixture that meets or
exceeds the temperature range of your climate. This rating
information can be found on most washer fluid containers.
After the engine has warmed up, operate the defroster for a
few minutes to reduce the possibility of smearing or freezing
the fluid on the cold windshield. Windshield washer solu -
tion used with water as directed on the container, aids
cleaning action, reduces the freezing point to avoid line clog -
ging, and is not harmful to paint or trim.CAUTION!
Overfilling or underfilling will cause oil aeration or loss
of oil pressure. This could damage your engine. WARNING!
Commercially available windshield washer solvents are
flammable. They could ignite and burn you. Care must
be exercised when filling or working around the washer
solution.

418 SERVICING AND MAINTENANCE
Engine Oil — Gas Engine
Change Engine Oil
The oil change indicator system will remind you that it is
time to take your vehicle in for scheduled maintenance. Refer
to “Scheduled Servicing” in this chapter for further informa -
tion.
NOTE:
Under no circumstances should oil change intervals exceed
8,000 miles (13,000 km), twelve months or 350 hours of
engine run time, whichever comes first. The 350 hours of
engine run or idle time is generally only a concern for fleet
customers. Engine Oil Selection — 6.4L
For best performance and maximum protection under all
types of operating conditions, the manufacturer only recom -
mends engine oils that are API Certified and meet the
requirements of FCA Material Standard MS-12633.
American Petroleum Institute (API) Engine Oil
Identification Symbol
This symbol means that the oil has been certified by
the American Petroleum Institute (API). The manu -
facturer only recommends API Certified engine oils.
This symbol certifies 0W-20, 5W-20, 0W-30, 5W-30 and
10W-30 engine oils.WARNING!
You can be badly injured working on or around a motor
vehicle. Only do service work for which you have the
knowledge and the proper equipment. If you have any
doubt about your ability to perform a service job, take
your vehicle to a competent mechanic.
CAUTION!
Do not use chemical flushes in your engine oil as the
chemicals can damage your engine. Such damage is not
covered by the New Vehicle Limited Warranty.

SERVICING AND MAINTENANCE 419
Engine Oil Viscosity (SAE Grade) — 6.4L Engine
Use Mopar SAE 0W-40 engine oil approved to FCA Material
Standard MS-12633 such as Pennzoil Ultra equivalent is
recommended for all operating temperatures.
The engine oil filler cap also shows the recommended engine
oil viscosity for your engine. For information on engine oil
filler cap location, refer to the “Engine Compartment” illus -
tration in this section.
Lubricants which do not have both the engine oil certifica -
tion mark and the correct SAE viscosity grade number
should not be used.
Synthetic Engine Oils
You may use synthetic engine oils provided the recom -
mended oil quality requirements are met, and the recom -
mended maintenance intervals for oil and filter changes are
followed.
Synthetic engine oils which do not have both the engine oil
certification mark and the correct SAE viscosity grade
number should not be used. Materials Added To Engine Oil
The manufacturer strongly recommends against the addi -
tion of any additives (other than leak detection dyes) to the
engine oil. Engine oil is an engineered product and its perfor -
mance may be impaired by supplemental additives.
Disposing Of Used Engine Oil And Oil Filters
Care should be taken in disposing of used engine oil and oil
filters from your vehicle. Used oil and oil filters, indiscrimi -
nately discarded, can present a problem to the environment.
Contact an authorized dealer, service station or govern -
mental agency for advice on how and where used oil and oil
filters can be safely discarded in your area.
Engine Oil Filter
The engine oil filter should be replaced with a new filter at
every engine oil change.
Engine Oil Filter Selection
This manufacturer's engines have a full-flow type disposable oil
filter. Use a filter of this type for replacement. The quality of
replacement filters varies considerably. Only high quality filters
should be used to assure most efficient service. Mopar engine oil
filters are high quality oil filters and are recommended. 7

428 SERVICING AND MAINTENANCE
Body Lubrication
Locks and all body pivot points, including such items as seat
tracks, door hinge pivot points and rollers, liftgate, tailgate,
decklid, sliding doors and hood hinges, should be lubricated
periodically with a lithium based grease, such as Mopar
Spray White Lube to assure quiet, easy operation and to
protect against rust and wear. Prior to the application of any
lubricant, the parts concerned should be wiped clean to
remove dust and grit; after lubricating excess oil and grease
should be removed. Particular attention should also be given
to hood latching components to ensure proper function.
When performing other underhood services, the hood latch,
release mechanism and safety catch should be cleaned and
lubricated.
The external lock cylinders should be lubricated twice a year,
preferably in the Fall and Spring. Apply a small amount of a
high quality lubricant, such as Mopar Lock Cylinder Lubri -
cant directly into the lock cylinder. Windshield Wiper Blades
Clean the rubber edges of the wiper blades and the wind -
shield periodically with a sponge or soft cloth and a mild
nonabrasive cleaner. This will remove accumulations of salt
or road film.
Operation of the wipers on dry glass for long periods may
cause deterioration of the wiper blades. Always use washer
fluid when using the wipers to remove salt or dirt from a dry
windshield.
Avoid using the wiper blades to remove frost or ice from the
windshield. Keep the blade rubber out of contact with petro -
leum products such as engine oil, gasoline, etc.
NOTE:
Life expectancy of wiper blades varies depending on
geographical area and frequency of use. Poor performance of
blades may be present with chattering, marks, water lines or
wet spots. If any of these conditions are present, clean the
wiper blades or replace as necessary.

432 SERVICING AND MAINTENANCE
system and adjacent body areas for broken, damaged, dete -
riorated, or mispositioned parts. Open seams or loose
connections could permit exhaust fumes to seep into the
passenger compartment. In addition, have the exhaust
system inspected each time the vehicle is raised for lubrica -
tion or oil change. Replace as required.
Under normal operating conditions, the catalytic converter
will not require maintenance. However, it is important to
keep the engine properly tuned to assure proper catalyst
operation and prevent possible catalyst damage.
NOTE:
Intentional tampering with emissions control systems can
result in civil penalties being assessed against you.WARNING!
• Exhaust gases can injure or kill. They contain carbon
monoxide (CO), which is colorless and odorless.
Breathing it can make you unconscious and can eventu -
ally poison you. To avoid breathing CO, refer to “Safety
Tips” in “Safety” for further information.
• A hot exhaust system can start a fire if you park over
materials that can burn. Such materials might be grass
or leaves coming into contact with your exhaust system.
Do not park or operate your vehicle in areas where your
exhaust system can contact anything that can burn. CAUTION!
• The catalytic converter requires the use of unleaded
fuel only. Leaded gasoline will destroy the effective -
ness of the catalyst as an emissions control device and
may seriously reduce engine performance and cause
serious damage to the engine.
• Damage to the catalytic converter can result if your
vehicle is not kept in proper operating condition. In the
event of engine malfunction, particularly involving
engine misfire or other apparent loss of performance,
have your vehicle serviced promptly. Continued opera -
tion of your vehicle with a severe malfunction could
cause the converter to overheat, resulting in possible
damage to the converter and vehicle.

SERVICING AND MAINTENANCE 441
5. Place the gear selector momentarily into each gear posi -
tion (allowing time for the transmission to fully engage in
each position), ending with the transmission in PARK.
6. Remove the dipstick, wipe it clean and reinsert it until
seated.
7. Remove the dipstick again and note the fluid level on
both sides. The fluid level reading is only valid if there is
a solid coating of oil on both sides of the dipstick. Note
that the holes in the dipstick will be full of fluid if the
actual level is at or above the hole. The fluid level should
be between the “HOT” (upper) reference holes on the
dipstick at normal operating temperature. If the fluid
level is low, add fluid through the dipstick tube to bring
it to the proper level. Do not overfill. Use ONLY the spec -
ified fluid (see "Fluids And Lubricants" for fluid specifica -
tions). After adding any quantity of oil through the
dipstick tube, wait a minimum of two minutes for the oil
to fully drain into the transmission before rechecking the
fluid level.
NOTE:
If it is necessary to check the transmission below the oper -
ating temperature, the fluid level should be between the two
“COLD” (lower) holes on the dipstick with the fluid at
60-70°F / 16-21°C. Only use the COLD region of the dipstick as a rough reference when setting the fluid level after a trans -
mission service or fluid change. Re-check the fluid level, and
adjust as required, once the transmission reaches normal
operating temperature.
8. Reinsert the dipstick. Check for leaks. Release the parking
brake.
NOTE:
If it is necessary to check the transmission below the oper -
ating temperature, the fluid level should be between the two
COLD (lower) holes on the dipstick with the fluid at 68-86°F
/ 20-30°C. Only use the COLD region of the dipstick as a
rough reference when setting the fluid level after a transmis -
sion service or fluid change. Re-check the fluid level, and
adjust as required, once the transmission reaches normal
operating temperature. CAUTION!
If the fluid temperature is below 50 °F (10 °C) it may not
register on the dipstick. Do not add fluid until the
temperature is elevated enough to produce an accurate
reading. Run the engine at idle, in PARK, to warm the
fluid.
7

TECHNICAL SPECIFICATIONS 483
FLUID CAPACITIES U.S. Metric
Fuel (Approximate)
Standard Rear Tank 52 Gallons 197 Liters
Optional Midship Tank 22 Gallons 83 Liters
Engine Oil With Filter
6.4L Engine (We recommend you use SAE 0W-40, Synthetic API Certified) 7 Quarts 6.6 Liters
Cooling System
6.4L Engine (We recommend you use Mopar Antifreeze/Coolant 10 Year/
150,000 Mile Formula). 16.6 Quarts 15.7 Liters
8

484 TECHNICAL SPECIFICATIONS
FLUIDS AND LUBRICANTS
Engine Component Fluid, Lubricant, or Genuine Part
Engine Coolant We recommend you use Mopar Antifreeze/Coolant
10–Year/150,000 Mile Formula OAT (Organic Additive
Technology).
Engine Oil – 6.4L Engine For best performance and maximum protection under all
types of operating conditions, the manufacturer only
recommends full synthetic engine oils that meet the
American Petroleum Institute (API) categories of SN. The
manufacturer recommends the use of Pennzoil Ultra 0W-40
or equivalent Mopar engine oil meeting the requirements of
FCA Material Standard MS-12633 for use in all operating
temperatures.
Engine Oil Filter – 6.4L Engine We recommend you use Mopar Engine Oil Filters.
Spark Plugs – 6.4L Engine We recommend you use Mopar Spark Plugs.
Fuel Selection – 6.4L Engine 89 Octane Recommended - 87 Octane Acceptable, 0-15%
Ethanol.

591
Auto Unlock, Doors ................................................................ 269
Automatic Door Locks ............................................................. 37
Automatic Headlights .............................................................. 68
Automatic Temperature Control (ATC) ................................ 89
Automatic Transmission ................................................ 265, 442
Adding Fluid ....................................................................... 442
Fluid And Filter Change .................................................... 442
Fluid Change........................................................................ 442
Fluid Level Check ....................................................... 439, 440
Fluid Type .................................................................... 439, 486
Shifting.................................................................................. 256
Special Additives................................................................. 439
Automatic Transmission Limp Home Mode ...................... 269
Auxiliary Driving Systems .................................................... 174
Axle Fluid................................................................. 442, 443, 486
Axle Lubrication.............................................................. 442, 443
B
Back-Up .................................................................................... 326
Back-Up Camera ..................................................................... 326
Battery............................................................................... 148, 417
Charging System Light....................................................... 148
Keyless Key Fob Replacement ............................................ 19
Battery Saver Feature ............................................................... 71
Belts, Seat ................................................................................. 241
Body Builders Guide ................................................................ 14
Body Mechanism Lubrication ............................................... 428 B-Pillar Location ......................................................................450
Brake Assist System ................................................................163
Brake Control System .............................................................162
Brake Fluid .......................................................................438, 486
Brake System....................................................................438, 476
Fluid Check ..........................................................................438
Master Cylinder ...................................................................438
Parking ..................................................................................252
Warning Light......................................................................146
Brake/Transmission Interlock ..............................................256
Bulb Replacement ...................................................................371
Bulbs, Light ......................................................................243, 371
C
Cab Top Clearance Lights ......................................................379
Camera...................................................................................... 326
Camera, Rear....................................................................326, 330
Capacities, Antifreeze (Engine Coolant) ..............................483
Capacities, Fluid ......................................................................483
Caps, Filler
Oil (Engine) ..................................................................415, 419
Power Steering .....................................................................284
Radiator (Coolant Pressure)...............................................436
Car Washes ..............................................................................471
Carbon Monoxide Warning ...........................................240, 482
Cargo Light ................................................................................71
Cellular Phone .........................................................................555 11

593
Differential, Limited Slip ....................................................... 281
Dipsticks
Power Steering..................................................................... 284
Disabled Vehicle Towing ....................................................... 406
Disposal
Antifreeze (Engine Coolant) .............................................. 436
Do Not Disturb ........................................................................ 579
Door Ajar.................................................................................. 150
Door Ajar Light ....................................................................... 150
Door Locks
Automatic ............................................................................... 37
Doors........................................................................................... 32
Drag And Drop Menu ............................................................ 487
Driver’s Seat Back Tilt .............................................................. 39
Driving
Through Flowing, Rising, Or Shallow Standing Water ....364
Dual Rear Wheels ................................................... 396, 467, 477
E
Electric Brake Control System ............................................... 162
Anti-Lock Brake System ..................................................... 161
Electronic Roll Mitigation .......................................... 166, 170
Electrical Power Outlets......................................................... 117
Electronic Range Select (ERS)........................................ 262, 270
Electronic Stability Control (ESC) ........................................ 166
Electronic Throttle Control Warning Light ......................... 149
Electronically Shifted Transfer Case .................................... 272 Emergency Braking.................................................................252
Emergency, In Case Of
Freeing Vehicle When Stuck ..............................................405
Hazard Warning Flasher ....................................................366
Jacking...................................................................................390
Jump Starting .......................................................................398
Emission Control System Maintenance ...............................159
Engine .......................................................................................415
Air Cleaner ...........................................................................420
Break-In Recommendations...............................................251
Compartment Identification ..............................................415
Coolant (Antifreeze)............................................................ 484
Exhaust Gas Caution................................................... 240, 482
Fails To Start.........................................................................249
Flooded, Starting .................................................................249
Fuel Requirements ..............................................................479
Jump Starting .......................................................................398
Oil ..................................................................................418, 484
Oil Filler Cap ................................................................415, 419
Oil Filter ................................................................................419
Oil Reset ................................................................................130
Oil Selection .........................................................................418
Oil Synthetic .........................................................................419
Overheating..........................................................................401
Starting..................................................................................246
Engine Oil Viscosity................................................................419 11