turn signal Ram ProMaster 2014 Owner's Manual
[x] Cancel search | Manufacturer: RAM, Model Year: 2014, Model line: ProMaster, Model: Ram ProMaster 2014Pages: 410, PDF Size: 2.83 MB
Page 16 of 410
WARNING!(Continued)
•Do not leave children or animals inside parked
vehicles in hot weather. Interior heat build-up may
cause serious injury or death.
CAUTION!
An unlocked car is an invitation to thieves. Always
remove the key from the ignition and lock all the
doors when leaving the vehicle unattended.
Locking Doors With A Key
You can insert the key with either side up. To lock the
door, turn the key to the right. To unlock the door, turn
the key to the left. Refer to “Body Lubrication” in
“Maintaining Your Vehicle” for maintenance procedures.
Key-In-Ignition Reminder
Opening the driver’s door when the key is in the ignition
and the ignition switch position is OFF/LOCK, sounds a
signal to remove the key.
STEERING WHEEL LOCK — IF EQUIPPED
Your vehicle may be equipped with a passive steering
wheel lock. This lock prevents steering the vehicle with-
out the ignition key. If the steering wheel is moved
approximately a half turn in either direction, and the key
is not in the ignition, the steering wheel will lock.
To Manually Lock The Steering Wheel
With the engine running, rotate the steering wheel one-
quarter revolution in either direction, turn off the engine
and remove the key. Turn the steering wheel slightly in
either direction until the lock engages.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Page 19 of 410
NOTE:Changes or modifications not expressly approved
by the party responsible for compliance could void the
user’s authority to operate the equipment.
VEHICLE SECURITY ALARM
The Vehicle Security Alarm monitors the vehicle doors
and ignition for unauthorized operation. When the Ve-
hicle Security Alarm is activated, interior switches for
door locks are disabled. The system provides both au-
dible and visible signals, for the first three minutes the
horn will sound and the turn signal lights will flash. For
an additional 15 minutes only the turn signal lights will
flash.
Rearming Of The System
The Vehicle Security Alarm will rearm itself after the 15
additional minutes of turn lamps flashing, if the system
has not been disabled. If the condition which initiated the alarm is still present, the system will ignore that condi-
tion and monitor the remaining doors and ignition.
To Arm The System
To Arm The System The Vehicle Security Alarm will set
when you use the Remote Keyless Entry (RKE) transmit-
ter to lock the doors. If a door or the bonnet is not
properly shut, it will be excluded from the perimetral
testing by the alarm system.
To Disarm The System
Use the RKE transmitter to unlock the door and disarm
the system.
The Vehicle Security Alarm will also disarm if a pro-
grammed Sentry Key® is inserted into the ignition
switch. To exit the alarming mode, press the RKE trans-
mitter UNLOCK button, or insert a programmed Sentry
Key® into the ignition switch.
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17
Page 21 of 410
NOTE:The line of transmission must not be blocked with
metal objects.To Unlock The Doors
Press and release the UNLOCK button on RKE transmit-
ter once to unlock only the front doors. Press and release
the CARGO UNLOCK button on RKE transmitter once to
unlock the cargo area (rear lateral sliding doors and rear
door). The turn signal lights will flash to acknowledge
the unlock signal.
To Lock The Doors
Press and release the LOCK button on the RKE transmit-
ter to lock all doors. The turn signal lights will flash and
the horn will chirp to acknowledge the signal. If a door is
ajar the turn signal lights will flash at an increased rate
and there will be no horn chirp, this is to indicate that a
door is still ajar.
Remote Keyless Entry Transmitter
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19
Page 38 of 410
Energy Management Feature
This vehicle has a safety belt system with an Energy
Management feature in the front seating positions to help
further reduce the risk of injury in the event of a head-on
collision.
This safety belt system has a retractor assembly that is
designed to release webbing in a controlled manner. This
feature is designed to help reduce the belt force acting on
the occupant’s chest.
Seat Belt Pretensioners
The seat belts for all front seating positions are equipped
with pretensioning devices that are designed to remove
slack from the seat belt in the event of a collision. These
devices may improve the performance of the seat belt by
assuring that the belt is tight around the occupant early
in a collision. Pretensioners work for all size occupants,
including those in child restraints.NOTE:
These devices are not a substitute for proper seat
belt placement by the occupant. The seat belt still must be
worn snugly and positioned properly.
The pretensioners are triggered by the Occupant Re-
straint Controller (ORC). Like the air bags, the preten-
sioners are single use items. A deployed pretensioner or
a deployed air bag must be replaced immediately.
Enhanced Seat Belt Use Reminder System
(BeltAlert®)
BeltAlert® is a feature intended to remind the driver and
front passenger(s) to fasten their seat belts. The feature is
active whenever the ignition is on. If the driver or front
seat passenger(s) is unbelted, the Seat Belt Reminder
Light will turn on and remain on until the front seat belts
are fastened. When the driver is unbelted during the first
six seconds from key on, in addition to the visual signal,
an acoustic warning of maximum six seconds starts
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE
Page 69 of 410
WARNING!(Continued)
•Check mounting of mats on a regular basis. Always
properly reinstall and secure floor mats that have
been removed for cleaning.
• Always make sure that objects cannot fall into the
driver footwell while the vehicle is moving. Ob-
jects can become trapped under the brake pedal
and accelerator pedal causing a loss of vehicle
control.
• If required, mounting posts must be properly in-
stalled, if not equipped from the factory.
Failure to properly follow floor mat installation or
mounting can cause interference with the brake
pedal and accelerator pedal operation causing loss of
control of the vehicle.
Periodic Safety Checks You Should Make Outside
The Vehicle
Tires
Examine tires for excessive tread wear and uneven wear
patterns. Check for stones, nails, glass, or other objects
lodged in the tread or sidewall. Inspect the tread for cuts
and cracks. Inspect sidewalls for cuts, cracks and bulges.
Check the wheel nuts for tightness. Check the tires
(including spare) for proper cold inflation pressure.
Lights
Have someone observe the operation of brake lights and
exterior lights while you work the controls. Check turn
signal and high beam indicator lights on the instrument
panel.
2
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67
Page 72 of 410
▫Daytime Running Lights — If Equipped ......92
▫ Lights-On Reminder ....................92
▫ Battery Saver .........................92
▫ Fog Lights — If Equipped ................93
▫ Turn Signals ..........................93
▫ Parking Lights ........................93
▫ Lane Change Assist ....................93
▫ High Beam/Low Beam Select Switch ........93
▫ Flash-To-Pass .........................94
▫ Follow Me Home/Headlight Delay ..........94
▫ Map/Dome/Lights .....................95
WINDSHIELD WIPERS AND WASHERS ......98
▫ Windshield Wipers .....................98 ▫
Intermittent Wiper System ...............98
▫ Low Speed ...........................99
▫ High Speed ..........................99
▫ Mist Feature ..........................99
▫ Windshield Washer Operation .............99
TELESCOPING STEERING COLUMN ........100
ELECTRONIC SPEED CONTROL ...........101
▫ To Activate ......................... .102
▫ To Set A Desired Speed .................102
▫ To Deactivate ....................... .103
▫ To Resume Speed .....................103
▫ To Vary The Speed Setting ...............103
▫ To Accelerate For Passing ................105
70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 92 of 410
CAUTION!
To prevent possible damage, do not slam the hood to
close it. Use a firm downward push at the front center
of the hood to ensure that both latches engage.
WARNING!
Be sure the hood is fully latched before driving your
vehicle. If the hood is not fully latched, it could open
when the vehicle is in motion and block your vision.
Failure to follow this warning could result in serious
injury or death.
LIGHTS
Multifunction Lever
The multifunction lever controls the operation of the
headlights, parking lights, turn signals, headlight beam
selection and the passing lights. The multifunction lever
is located on the left side of the steering column.
Multifunction Lever
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 94 of 410
Daytime Running Lights — If Equipped
NOTE:When the headlights are turned on, the Daytime
Running Lights will be deactivated.
To activate the Daytime Running Lights (DRL), rotate the
end of the multifunction lever to the O (Off) position.
NOTE: The low beams and side/taillights will not be on
with DRL. The DRL function may be programmed to be
ON or OFF through the Uconnect® system screen. Refer
to “ Uconnect® Settings ” in “Understanding Your In-
strument Panel” for further information.
The high beam lights will come on as Daytime Running
Lights (lower intensity), whenever the ignition is ON, the
engine is running, the headlight switch is off, the parking
brake is off, the turn signal is off, and the shift lever is in
any position except PARK.
Lights-On Reminder
If the headlights or parking lights are not turned OFF
when the ignition is turned OFF a chime will sound to
alert the driver when the driver’s door is opened.
Battery Saver
To protect the life of your vehicle’s battery when the
ignition is OFF and any door is left ajar for 10 minutes the
interior lights will automatically turn off.
If the headlights remain on while the ignition is cycled
OFF, the exterior lights will automatically turn off after
eight minutes. If the headlights are turned on and left on
for eight minutes while the ignition is OFF, the exterior
lights will automatically turn off.
NOTE: Battery saver mode is cancelled if the ignition is
ON.
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE
Page 95 of 410
Fog Lights — If Equipped
The fog light switch is located on the center
stack of the instrument panel, just below the
climate controls. Press the switch once to turn
the fog lights on. Press the switch a second time to turn
the fog lights off.
Turn Signals
Move the multifunction lever up or down and the arrows
on each side of the instrument cluster flash to show
proper operation of the front and rear turn signal lights.
NOTE: If either light remains on and does not flash, or
there is a very fast flash rate, check for a defective outside
light bulb. If an indicator fails to light when the lever is
moved, it would suggest that the indicator bulb is
defective.
Parking Lights
These lights can only be turned on with ignition key in
the STOP position or removed, by moving the end of the
multifunction lever to O (off) position and then to the
headlight position.
The warning light telltale in the instrument panel comes
on. The lights stay on until the next ignition cycle is
performed.
Lane Change Assist
Tap the lever up or down once, without moving beyond
the detent, and the turn signal (right or left) will flash five
times then automatically turn off.
High Beam/Low Beam Select Switch
Pull the multifunction lever toward you to switch the
headlights to high beam. Pull the lever a second time to
switch the headlights back to low beam.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93
Page 96 of 410
Flash-To-Pass
You can signal another vehicle with your headlights by
partially pulling the multifunction lever toward the steer-
ing wheel. This will cause the high beam headlights to
turn on until the lever is released.
Follow Me Home/Headlight Delay
When this feature is selected the driver can choose to
have the headlights remain on for a preset period of time.
Activation
Remove the key or turn the ignition to the OFF/LOCK
position, and pull the multifunction lever toward the
steering wheel, within two minutes. Each time the lever
is pulled, the activation of the lights will be extended by
30 seconds. The activation of the lights can be extended to
a maximum of 210 seconds.The warning light on the instrument panel will light up
and the corresponding message will appear in the EVIC
display for as long as the function is activated. The
warning light comes on when the lever is operated and
stays on until the function is automatically deactivated.
Each movement of the lever only increases the amount of
time the lights stay on.
Deactivation
Pull the multifunction lever toward the steering wheel
and hold it for more than two seconds.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE