set time on radio Ram ProMaster 2017 Owner's Manual

turn the system OFF, rotate the center ring upward a
second time. The Cruise Indicator Light will turn off. The
system should be turned off when not in use.
WARNING!
Leaving the Electronic Speed Control system on when
not in use is dangerous. You could accidentally set the
system or cause it to go faster than you want. You could
lose control and have an accident. Always leave the
system OFF when you are not using it.
To Set A Desired Speed
Turn the Electronic Speed Control ON. When the vehicle
has reached the desired speed, move the electronic speed
control lever upward SET(+) and release. Release the
accelerator and the vehicle will operate at the selected
speed.
NOTE:The vehicle should be traveling at a steady speed
and on level ground before moving the electronic speed
control lever upward SET(+).
To Deactivate
A soft tap on the brake pedal, pushing the RES button, or
normal brake pressure while slowing the vehicle will deactivate Electronic Speed Control without erasing the set
speed memory. Rotating the center ring upward to turn the
system OFF or turning the ignition switch OFF erases the
set speed memory.
To Resume Speed
To resume a previously set speed, push the RES button and
release. Resume can be used at any speed above 20 mph
(32 km/h) up to the maximum speed of 100 mph
(160 km/h).
To Vary The Speed Setting
To Increase Speed
When the Electronic Speed Control is set, you can increase
speed by tapping the Speed Control lever up (+).
The drivers preferred units can be selected through the
radio settings if equipped. Refer to ”Uconnect Settings” in
“Understanding Your Instrument Panel” for more informa-
tion. The speed increment shown is dependant on the
chosen speed unit of U.S. (mph) or Metric (km/h):
U.S. Speed (mph)
•
Tapping the Speed Control lever up (+) once will result
in a 1 mph increase in set speed. Each subsequent tap of
the lever results in an increase of 1 mph.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83

•Language
• Buzzer Volume
• Seat Belt Buzzer (*)
• (*) just available after SBR disable made by CHR
Service
• Service (Diesel Only)
• DRL - Daytime Running Lights (if equipped)
• Exit menu
NOTE:
• If equipped with Uconnect 5.0 radio, some customer
programmable features will display in the Uconnect
5.0 system. Refer to the radio supplement for further
Uconnect 5.0 information.
• The clock setting and Uconnect 5.0 clock setting pro-
cedure can be done through the radio or the Instru-
ment Cluster Display.
Selecting An Option Of The Main Menu Without Submenu
1. Briefly push and release the MODEbutton to select the
main menu option to set. 2. Push and release the
UPorDOWNarrow
button (by single pushes) to select the new setting.
3. Briefly push and release the MODEbutton to store the
new setting and go back to the main menu option
previously selected.
Selecting An Option Of The Main Menu With Submenu
1. Briefly push and release the MODEbutton to display
the first submenu option.
2. Push and release the UP
orDOWNarrow
button (by single pushes) to scroll through all the
submenu options.
3. Briefly push and release the MODEbutton to select the
displayed submenu option and to open the relevant
setup menu.
4. Push and release the UP
orDOWNarrow
button (by single pushes) to select the new setting for
this submenu option.
5. Briefly push and release the MODEbutton to store the
new setting and go back to the previously selected
submenu option.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 123

•Seat Belt Buzzer (*)
• (*) just available after SBR disable made by CHR
Service
• Service (Diesel Only)
• DRL - Daytime Running Light (if equipped)
• Exit menu
NOTE:
• If equipped with Uconnect 5.0/5.0N radio, some cus-
tomer programmable features will display in the
Uconnect 5.0/5.0N system. Refer to the Uconnect Set-
tings for further Uconnect 5.0/5.0N information.
• The Instrument Cluster Display clock setting and
Uconnect 5.0/5.0N clock setting procedure can be done
through the radio or the Instrument Cluster Display.
CYBERSECURITY
Your vehicle may be a connected vehicle and may be
equipped with both wired and wireless networks. These
networks allow your vehicle to send and receive informa-
tion. This information allows systems and features in your
vehicle to function properly. Your vehicle may be equipped with certain security fea-
tures to reduce the risk of unauthorized and unlawful
access to vehicle systems and wireless communications.
Vehicle software technology continues to evolve over time
and FCA US LLC, working with its suppliers, evaluates
and takes appropriate steps as needed. Similar to a com-
puter or other devices, your vehicle may require software
updates to improve the usability and performance of your
systems or to reduce the potential risk of unauthorized and
unlawful access to your vehicle systems.
The risk of unauthorized and unlawful access to your
vehicle systems may still exist, even if the most recent
version of vehicle software (such as Uconnect software) is
installed.
WARNING!
•
It is not possible to know or to predict all of the
possible outcomes if your vehicle’s systems are
breached. It may be possible that vehicle systems,
including safety related systems, could be impaired
or a loss of vehicle control could occur that may
result in an accident involving serious injury or
death.
(Continued)
4
UNDERSTANDING YOUR INSTRUMENT PANEL 127

NOTE:The operation of many of the resources mentioned
in this publication depends on technology used by radio
stations and other base stations, which may not be avail-
able at certain times and/or in particular locations.
Recommendations
Road Safety
We recommend that you learn how to use the various radio
features (for example, Station Preset) before you begin your
journey.
WARNING!
Turning the volume up too high may be dangerous for
the driver and other people on the road. You should
adjust the volume so that you are always able to hear
sounds around you (e.g. horns, ambulances, police
cars, etc.).
Radio Reception
Reception varies constantly while driving.
Reception may be affected by mountains, buildings or
bridges, especially when further away from the transmitter
of the tuned radio station.
CAUTION!
When listening to traffic news, you may notice louder
volume compared to normal playback.
Care And Maintenance
The radio structure is built to guarantee many years of
operation without needing maintenance. In case of a fault,
contact your local authorized dealer.
Use only a soft, anti-static cloth to clean the front of the
radio.
Detergents and waxes can damage the surface.
Identification Number
The radio has a unique identification number (found on the
warranty card). This card is required as proof of ownership
if the radio is stolen or when seeking assistance. Do not
store the warranty card in the vehicle.
Security Code
This radio has a serial number (found on the warranty
card).
Present this card as proof of ownership if the radio is stolen
or if you require assistance.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 129

Searching for Stations In Manual Mode
Pushing
orfor more than two seconds displays
the selected radio station frequency. Each time a button
is pushed, the radio station frequency is increased or
decreased according to the default search pattern for the
selected band (100 kHz for FM and 10k Hz for AM).
When the search button is pushed and held, the radio
station frequency will continue to be increased or de-
creased. If the buttons are not pushed for five seconds,
the display will show the message AUTOand manual
search mode will be canceled. When the search is
complete, the display will show the tuned band and
station in the format F1 106.9, or, if the station found
was previously stored in memory, the display will show
the channel where it is stored and the tuned station.
Mute/Pause
Pushing this button mutes the sound. The display will
switch between MUTE ONand the previous display
(3 seconds).
Pushing the button again restores the audio without chang-
ing the original volume setting. The display will show
MUTE OFF for three seconds, and then return to the
previous display mode.
When the
or, Audio, 1, 2, 3, 4, 5, 6, BAND/AS
buttons and SRC are pushed in Mute/Pausedmode,
these will be implemented and the audio will be re-
stored without changing the original volume. 4
UNDERSTANDING YOUR INSTRUMENT PANEL 135

Shuffle (Random Playback)
Pushing the RND button enables or disables theshuffle
feature. When enabled, the RND indicator is switched on
and the display will show RND ONfor two seconds. The
display will then revert to the previous view.
When you push this button again, the function is disabled,
the RND indicator is turned off and the display will show
RND OFF for two seconds. The display then reverts to the
previous view.
If the RND function is enabled, the music forward/reverse
will be random, both in normal mode and Fast Track mode.
In this case, Buttons 1 and 2 (forward/reverse folder) have
the exact same function as
or(music forward/
reverse), respectively.
Switching Between Display Modes
When you push the DISP button for less than two seconds,
information about the track being played will alternate in
the following sequence: Track
TimeTitleAlbum
ArtistFileFolderTrack. At the first touch of
the button, the display now shows the information type
related to the track being played, for example, if the
current information is track, the display will show
TIME. If you push any other buttons or if the DISP button is not pushed for two seconds, the information
type that is on the display will be selected. When the file
that is being played does not contain the selected
information, the radio will display
NO NAME.
UCONNECT RADIOS
For detailed information about your Uconnect 3.0, and 5.0
radio, refer to your Uconnect Owner ’s Manual Supple-
ment.
UCONNECT SETTINGS
The Uconnect system uses a combination of buttons on the
touchscreen and buttons on the faceplate located on the
center of the instrument panel that allows you to access
and change the customer programmable features. Many
features can vary by vehicle.
CAUTION!
Do NOT attach any object to the touchscreen, doing so
can result in damage to the touchscreen.
144 UNDERSTANDING YOUR INSTRUMENT PANEL

Setting NameSelectable Options
Subscription Info Sirius ID
NOTE:
New vehicle purchasers or lessees will receive a free limited time subscription to SiriusXM Satellite Radio with your
radio. Following the expiration of the free services, it will be necessary to access the information on the Subscription
Information screen to re-subscribe.
1. Press the “Subscription Info” button on the touchscreen to access the Subscription Information screen.
2. Write down the Sirius ID numbers for your receiver. To reactivate your service, either call the number listed on the screen or visit the provider online.
SiriusXM Travel Link is a separate subscription and is available for U.S. residents only.
Restore Settings — If Equipped
After pressing the “Restore Settings” button on the touch-
screen the following settings will be available:
Setting Name Selectable Options
Restore Settings YesCancel
NOTE: When this feature is selected, it will reset the Display, Clock, Audio, and Radio Settings to their default set-
tings. Once the settings are restored, a pop up appears stating settings reset to default.Press the okay button on the
touchscreen to exit.
154 UNDERSTANDING YOUR INSTRUMENT PANEL

WARNING!
•Take care to avoid the radiator cooling fan whenever
the hood is raised. It can start anytime the ignition
switch is ON. You can be injured by moving fan
blades.
• Remove any metal jewelry such as rings, watch
bands and bracelets that could make an inadvertent
electrical contact. You could be seriously injured.
• Batteries contain sulfuric acid that can burn your
skin or eyes and generate hydrogen gas which is
flammable and explosive. Keep open flames or
sparks away from the battery.
1. Set the parking brake, shift the automatic transmission into PARK and turn the ignition to the OFF position.
2. Turn off the heater, radio, and all unnecessary electrical accessories.
3. If using another vehicle to jump-start the battery, park the vehicle within the jumper cables reach, set the
parking brake and make sure the ignition is OFF.
WARNING!
Do not allow vehicles to touch each other as this could
establish a ground connection and personal injury
could result.
Jump-Starting Procedure
WARNING!
Failure to follow this jump-starting procedure could
result in personal injury or property damage due to
battery explosion.
CAUTION!
Failure to follow these procedures could result in
damage to the charging system of the booster vehicle
or the discharged vehicle.
Connecting The Jumper Cables
1. Connect the positive (+)end of the jumper cable to the
remote positive (+)post of the discharged vehicle.
268 WHAT TO DO IN EMERGENCIES