checking oil RENAULT CLIO 1997 X57 / 1.G Petrol Engines Workshop Manual

ENGINE AND PERIPHERALS
S
pecifications10
CRANKSHAFT
Number of bearings5
Roll hardened
journals (mm):
- nominal diameter 54.795 ± 0.01
- repair diameter 54.550 ± 0.005
Roll hardened crankpins (mm)
:
- nominal diamete
r43.98
- repair diameter43.73
End float 0.045 - 0.852 worn
0.045 - 0.252 unworn
There are shims of various thicknesses.
If grinding is carried out, the roll hardening mus
t
remain intact over an angle of 140° in the areas
shown by the arrows.
These areas are defined on sections (A) and (B) ta-
ken as an example.
0
- 0.02
0
- 0.02
79260-1G1
OIL PUMP
Minimum oil pressure at 80
°C:
- Idle spee
d1 bar
- 4000 rpm3 bars
The pump is of the gear pump type.
Remove the cover and the valve of the oil pump.
92313S
Checking the oil pump
Check the clearances:
Clearance
A(in mm) :
- minimum
0.110
- maximum0.249
80142R1
10-17
Page 1 of 1 E_Series_19
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_19.htm

97160-1S1
FigurineMethod
referencePart
NumberDescription
ENGINE AND PERIPHERALS
S
pecial tooling required10
96508S1
Mot. 133000 00 133 000 Oil filter cap, 66 mm diameter
Mot. 127300 00 127 300 Tool for checking belt tension
Mot. 133500 00 133 500Pliers for removing valve stem seals
98503S
10-23
Page 1 of 1 E_Series_25
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_25.htm

ENGINE AND PERIPHERALS
En
gine repair10
92317S
91803G1 FITTING THE PISTON RINGS
Mount on the piston:
- the scraper ring (3),
- the taper compression piston ring (2), with the
"To
p" mark facing upwards,
- the upper piston ring (1), with the
"To
p" mark
facing upwards.
Once the seating of all the piston rings has been
adjusted, never alter this seating.
Oil and bed in the piston rings, seating the scrape
r
ring onto a solid part of the groove.Fit the "connecting rods - pistons - piston rings"
assemblies into the liners using the piston ring
compressor.
Before fitting the "liners - pistons - connecting
rods" assemblies into the cylinder block, do no
t
forget to fit the O-ring on each liner, ensuring
that it is not twisted.
Fit the assembly into the cylinder block in the pre-
established order, checking that a
0.1 mm shim
will pass freely between the liners.
92316S 918038630786314
10-41
Page 1 of 1 E_Series_43
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_43.htm

ENGINE AND PERIPHERALS
En
gine repair10
Fit:
- the oil pump, checking that the centring dowls
are present, and tighten to a torque value of
2.5 daN.m,
- the two sprockets and chain of the oil pump,
and tighten the three bolts mounting the
sprocket to the hub to
1 daN.m,
- the crankshaft end cover, sealing it with
Loctite
518.
The bead (H) should be
0.6 to 1 mm wide and
should be applied as shown in the diagram be-
low. - the crankshaft seal (bearing No.1), using tool
Mot. 1129-01; this tool is designed to ensure an
offset seal bearing surface. Lubricate the lip
and the outside of the seal.
92319R
92067R
-the crankshaft end seal, using tool
Mot. 1128-
01; lubricate the lip and the outside diamete
r
of the seal.
Turn over the s
pacer if the old seal has marked
the bearin
g surface.
92318R
10-43
Page 1 of 1 E_Series_45
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_45.htm