oil pressure RENAULT CLIO 1997 X57 / 1.G Petrol Engines Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 1997, Model line: CLIO, Model: RENAULT CLIO 1997 X57 / 1.GPages: 55, PDF Size: 4.15 MB
Page 19 of 55
ENGINE AND PERIPHERALS
S
pecifications10
CRANKSHAFT
Number of bearings5
Roll hardened
journals (mm):
- nominal diameter 54.795 ± 0.01
- repair diameter 54.550 ± 0.005
Roll hardened crankpins (mm)
:
- nominal diamete
r43.98
- repair diameter43.73
End float 0.045 - 0.852 worn
0.045 - 0.252 unworn
There are shims of various thicknesses.
If grinding is carried out, the roll hardening mus
t
remain intact over an angle of 140° in the areas
shown by the arrows.
These areas are defined on sections (A) and (B) ta-
ken as an example.
0
- 0.02
0
- 0.02
79260-1G1
OIL PUMP
Minimum oil pressure at 80
°C:
- Idle spee
d1 bar
- 4000 rpm3 bars
The pump is of the gear pump type.
Remove the cover and the valve of the oil pump.
92313S
Checking the oil pump
Check the clearances:
Clearance
A(in mm) :
- minimum
0.110
- maximum0.249
80142R1
10-17
Page 1 of 1 E_Series_19
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_19.htm
Page 22 of 55
ENGINE AND PERIPHERALS
Standard exchan
ge10
PREPARATION OF USED ENGINE FOR RETURN
The engine should be cleaned and drained (oil
and water
).
Leave on the used engine or put into the box use
d
for returning it:
- the dipstick and its guide,
- the flywheel or the starter plate,
- the clutch disc and mechanism,
- the fuel pump,
- the water pump,
- the crankshaft pulley,
- the cylinder head cover,
- the spark plugs,
- the belt tensioner,
- the pressure switch and temperature switch,
- the timing cover,
- the oil filter.
Do not forget to remove:
- all the flexible coolant pipes,
- the belt or belts (except timing belt).
The used engine must be fixed on to the wooden
base in the same way as the reconditioned en-
gine:
- plastic plugs and caps in place,
- cardboard cover all around it.
10-20
Page 1 of 1 E_Series_22
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_22.htm
Page 31 of 55
ENGINE AND PERIPHERALS
En
gine repair10
- the camshaft seal,
- the camshaft flange,
92078R
10010S
- the camshaft,
- the fuel pump (if fitted),
- the distributor with the ignition wiring loom,
- the thermostat housing,
- the spark plugs,
- the camshaft sprocket, after immobilising i
t
with
Mot. 799-01.
Compress the valve springs (e.g. with
FACOM tool
U43L).
Remove the collets, the upper cups, the springs,
the valves, the valve seals using the pliers
Mot.
1335 and the lower cups. The wearing of gloves is recommended during
this operation.
Do not allow any product to drip on to paintwork.
We would like to stress that the utmost care
should be taken in carr
ying out this operation to
prevent foreign bodies from penetrating the
pipes feeding oil under pressure to the camshafts
(pipes located both in the cylinder block and in
the c
ylinder head) and in the oil return pipe.
Failure to follow this instruction would in fact ris
k
blocking the nozzles of the valve rockers and qui-
ckly causing damage to the rocker cams and fin-
gers. Cleanin
g
It is very important not to scratch the sealing
faces of aluminium parts.
Use the product Decapjoint to dissolve any part of
the seal which remains.
Apply the product to the part to be cleaned; wai
t
about ten minutes, then remove it by means of a
wooden spatula.
10-29
Page 1 of 1 E_Series_31
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_31.htm