wheel torque RENAULT CLIO 1997 X57 / 1.G Petrol Engines Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 1997, Model line: CLIO, Model: RENAULT CLIO 1997 X57 / 1.GPages: 55, PDF Size: 4.15 MB
Page 7 of 55
ENGINE AND PERIPHERALS
Section and ti
ghtening torques(in daN.m and/or°)10
(1) Timing tension wheel nut: tighten to
5 daN.m
(2)
M6
bolt and nut: tighten to
1 daN.m
M8
bolt: tighten to
2.2 daN.m
(3) Pre-tighten to
2 daN.m, then angle tighten by
68°
±6°
DI1043
5 to 5.5
10-5
Page 1 of 1 E_Series_7
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_7.htm
Page 21 of 55
ENGINE AND PERIPHERALS
S
pecifications10
CONSUMABLES
PARTS TO BE RENEWED WHEN THEY HAVE BEEN
REMOVED
All seals and gaskets.
Flywheel bolts.
Valve guides.
Cylinder head bolts.
Crankshaft bearing bolts.
PRECAUTIONS
WASHING OF ENGINE
Protect the timing and alternator belts to avoid
splashing of water and washing products on to
them.
Do not allow water to penetrate the air inle
t
pipes.
FITTING OF THREAD INSERTS
The threaded holes in all the engine components
may be repaired using thread inserts.
Type QuantityComponent concernedParts Dept. Nos.
( SODICAM )
Loctite FRENETANCH (Locking and
sealing resin)
Loctite FRENBLOC (Locking and
sealing resin)
Loctite AUTOFORM
RHODORSEAL 5661
Loctite 518
Décapjoin
t
1 to 2 drops
Coa
t
Coat
Coat
Bead
Coa
t
Mounting bolts: flywheel, torque
converter starter plate
Crankshaft bearing (if the flywheel
mounting bolts have no locking
plate)
Flywheel bearing face on cranks-
haf
t
Sump, bearing cap, crankshaft
bearing
Water pump. crankshaft cove
r
Cleaning of aluminium cylinder
head gasket face
77 01 394 070
77 01 394 071
77 01 400 309
77 01 404 452
77 01 421 162
77 01 405 952
10-19
Page 1 of 1 E_Series_21
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_21.htm
Page 24 of 55
Mot. 792-03
Mot. 1132 Fi
gurineMethod
ReferencePart
NumberDescription
ENGINE AND PERIPHERALS
S
pecial tooling required10
Mot. 591-0400 00 059 104
Elé. 1382
00 00 138 200
78181S
10250
82919S1
80359S1
97628S
Mot. 799-0100 00 079 901
80357S
Mot. 1128-0100 00 112 801Tool for fitting crankshaft seal, timing side Angular wrench for tightening cylinder head
( 1/2" drive )
Spark plug wrench kit, limited tightening
torque
Pinion immobiliser for notched timing belt.
68658S
Mot. 1129-0100 00 112 901Tool for fitting crankshaft seal, flywheel side
92645-1S1
Mot. 1135-01
00 00 113 501Timing belt tensioning tool En
gine mounting plate for Desvil stand.
Set of 3 threaded rods for mounting engine
on the
Mot. 792-03. 00 00 079 203
00 00 113 200
Mot. 1127-01
00 00 112 701Tool for fitting camshaft seal
10-22
Page 1 of 1 E_Series_24
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_24.htm
Page 46 of 55
ENGINE AND PERIPHERALS
En
gine repair10
99179R1
Refit the sump and tighten to a torque value of
1 daN.m.
NOTE : A tight seal for the sump can only be ob-
tained using the special seal supplied by the afte
r-
sales service, except for engine
E7J 764 in which a
tight seal is achieved by using
RHODOR-SEAL
5661. Bead (D) should be
3 mm wide.
Do not forget to replace the two "half-moon"
seals at (A) with new ones.
Coat the flywheel bearing surface on the cranks-
haft with
AUTOFORM Loctite.
Fit the flywheel or the converter plate and immo-
bilise it with the toothed segment
Mot. 582-01.
Apply a drop of
FRENETANCH Loctite to the
bolts and tighten them to
5 - 5.5 daN.m.
Centre the clutch disc and secure the mechanism.
92068R
Refit the water pump, sealing it with
Loctite 518.
The bead (H) should be
0.6 to 1 mm wide and
should be applied as shown in the diagram below.
REFITTING THE CYLINDER HEAD
Remove the liner tool
Mot. 588.
Clean the gasket surfaces of the cylinder bloc
k
and the cylinder head.
Refit the cylinder head centring dowl.
The new cylinder head gasket.
The cylinder head (lubricate the threads and
underneath the bolt heads).
All the cylinder head bolts must be replaced
systematically after any removal.
10-44
Page 1 of 1 E_Series_46
04.08.2003 http://jester.com.ua/renault/motors/e/E_Series/css/E_Series_46.htm