ECU RENAULT CLIO 1999 X65 / 2.G Air Bag And Seat Belts Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 1999, Model line: CLIO, Model: RENAULT CLIO 1999 X65 / 2.GPages: 90, PDF Size: 0.54 MB
Page 18 of 90
Downloaded from www.Manualslib.com manuals search engine WIRING
Air bags and seat belt pretensioners
88
After deactivating the air bag function using the
fault finding tool and removing the passenger air
bag module :
• cut the passenger air bag wiring 60 mm from
the instrument panel wiring tape,
• unsheath the passenger air bag supply wiring
by 30 mm,
• strip the wiring provided in the kit and the
passenger air bag wiring by approximately10
mm,
• thread 2 cm of heat shrink sleeving (provided
in the kit) on each of the vehicle’s wiring lines,
• solder the vehicle’s wiring to the wiring in the
kit (B),
• position the heat shrink sleeving over the sol-
dered joins and heat it,
15668R
• refit and secure the passenger air bag module,
• connect the new connector to the passenger
air bag module,
• carry out a check using the fault finding tool.
Unlock the computer if everything is correct,
otherwise see the "Fault Finding " section.
SEAT BELT PRETENSIONERS
Description
They are mounted to the side of the front seats.
96438S
A pretensioner comprises :
- a special belt buckle (A),
- a pyrotechnic gas generator with its ignition
module (B).
DI8801R
88-16
Page 26 of 90
Downloaded from www.Manualslib.com manuals search engine WIRING
Air bags and seat belt pretensioners
88
Special case : the connector with lugs
A series of vehicles are fitted with a red connector
with lugs (A) on the passenger air bag module.
16008R
To disconnect it, carefully use a small screwdriver
as a lever , so as not to damage the lugs .
In the event of the lugs breaking, replace the
connector using the kit part number : 77 01 206
210 using the following method.
After deactivating the air bag function using the
fault finding tool and removing the passenger air
bag module :
• cut the passenger air bag wiring 60 mm from
the instrument panel wiring tape,
• unsheath the passenger air bag supply wiring
by 30 mm,
• strip the wiring provided in the kit and the
passenger air bag wiring by approximately10
mm,
• thread 2 cm of heat shrink sleeving (provided
in the kit) on each of the vehicle’s wiring lines,
15668R
• refit and secure the passenger air bag module,
• connect the new connector to the passenger
air bag module,
• carry out a check using the fault finding tool.
Unlock the computer if everything is correct,
otherwise see the "Fault Finding " section. • solder the vehicle’s wiring to the wiring in the
kit (B),
• position the heat shrink sleeving over the sol-
dered joins and heat it,
88-24
Page 27 of 90
Downloaded from www.Manualslib.com manuals search engine WIRING
Air bags and seat belt pretensioners
88
Refitting
IMPORTANT: the safety notes which must be fol-
lowed to refit or replace the passenger air bag
module must be observed .
If these procedures are not correctly observed the
systems may not operate correctly or may be acci-
dentally triggered, presenting a danger to the oc-
cupants of the vehicle.
Refitting is the opposite of removal
IMPORTANT: a 2nd generation passenger air bag
module must not be fitted to a vehicle fitted with
a 1
stgeneration computer (see the table on
pages 2 and 3).
Observe part numbers mentioned in the spare
parts catalogue, referring to vehicle equipment.
REMINDER: the computer in these vehicles can wi-
thstand several triggerings. Therefore, it does not
have to be replaced after every triggering of the
air bag(s) or pretensioners (see "Computer" sec-
tion).
IMPORTANT
• No foreign body (bolt,clip...) must be forgotten
when refitting the air bag module.
• Reconnect the passenger air bag module and
secure it (tightening torque : 0.6 daN.m).
• Press the connector in firmly on the module
side (strong clipping system).
• Attach a blue adhesive sticker " after sales sys-
tem tamperproof label" sold under part num-
ber : 77 01 205 356 on the air bag module
connector.
• After refitting everything, carry out a check
using the fault finding tool.
• Unlock the computer if everything is correct,
otherwise see the"Fault Finding" section.
SIDE AIR BAG MODULE
Description
It is fitted into the seatback of the front seats on
the door side.
It comprises :
- an inflatable bag,
- a pyrotechnic gas generator and ignition
module.
These components cannot be separated.
15132R
In order to work the inflatable bag tears through
the module cover, the foam and the seat trim.
NOTE: this system is operational after the ignition
has been switched on.
IMPORTANT:
The pyrotechnic systems (pretensioners or air
bags) must not be handled when near a heat
source or a flame because there is a risk that the
system will be triggered.
No measurements may be made on these systems
using an ohmmeter or any other electrical measu-
ring equipment: the system may be triggered due
to the operating current of the measuring equip-
ment.
88-25