wheel bolts RENAULT CLIO 2009 X85 / 3.G Owners Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2009, Model line: CLIO, Model: RENAULT CLIO 2009 X85 / 3.GPages: 264, PDF Size: 15.68 MB
Page 197 of 264
Downloaded from www.Manualslib.com manuals search engine
tool kit ...................................................(up to the end of the DU)hubcap tool ...........................................(up to the end of the DU)jack .......................................................(up to the end of the DU)wheelbrace ...........................................(up to the end of the DU)towing hitch...........................................(up to the end of the DU)wheelbrace ...........................................(up to the end of the DU)puncture................................................(up to the end of the DU)
5.9
ENG_UD12590_2Bloc-outils (X85 - B85 - C85 - S85 - K85 - Renault)ENG_NU_853-3_BCSK85_Renault_5
End piece for special wheel
bolt
3(depending on vehicle)
Towing hitch 4Refer to the information on “Towing” in Section 5.
Hubcap tool 5 or 6This tool is used to remove the wheel trims.
Jack 7Remove jack 7.To refit, lower the jack fully and unscrew it by one turn and pivot the base so that it can be stored.
Storage compartment 1(depending on vehicle)
This is for storing a lock nut.
Wheelbrace 2This is used to tighten or release the wheel bolts.
Tool kit
A is located in the tray under the luggage compartment carpet.Depending on the vehicle, lift the cover, then remove it.Take out the tool kit, lifting it at both ends.To return it, proceed in the reverse order to removal.
TOOL KIT
Tool kit (jack, wheelbrace, etc.)
1
A
7
2
3
4
56
Do not leave the tools unsecured inside the vehicle as they may come loose under braking. After use, check that all the tools are correctly clipped into the tool kit, then position it correctl\
y in its housing: there is a risk of injury.If wheel bolts are supplied in the tool kit, only use these bolts for the emergency spare wheel: refer to the label affixed to the emergency spare wheel.
The jack is designed for wheel changing purposes only. Under no circumstances should it be used for carrying out repairs un- derneath the vehicle or to gain access to the underside of the vehicle.
Page 198 of 264
Downloaded from www.Manualslib.com manuals search engine
hubcap tool ...........................................(up to the end of the DU)trims ......................................................(up to the end of the DU)
5.10
ENG_UD10599_1Enjoliveur - Roue (X85 - B85 - C85 - S85 - K85 - Renault)ENG_NU_853-3_BCSK85_Renault_5
Wheel trims - wheel
We would advise you to note down the number engraved on the tool so that you can replace it if it is lost.
Central wheel hubcap
(example: hubcap 4)
To remove it, insert the hubcap tool 6 (located in the tool kit) into recess 5.
To refit it, position it in line with recess 5 and tighten it with tool 6.
Hubcap (example hubcap 1)
Remove the wheel trim using hubcap
tool 2 (located in the tool kit) by en- gaging the hook in the opening near
valve 3.
To refit it, align it with valve 3. Push the retaining hooks in fully, starting with side A near the valve, followed by B and C, finishing at D opposite the
valve.
WHEEL TRIMS - WHEEL
1
4
5
6
2
3
D
C
A
B
Do not leave the tools un- secured inside the vehicle as they may come loose under braking. After use, check that all the tools are correctly clipped into the tool kit, then position it correctly in its housing: there is a risk of injury.If wheel bolts are supplied in the tool kit, only use these bolts for the emergency spare wheel: refer to the label affixed to the emergency spare wheel.The jack is designed for wheel changing purposes only. Under no circumstances should it be used for carrying out repairs underneath the vehicle or to gain access to the un- derside of the vehicle.
Page 199 of 264
Downloaded from www.Manualslib.com manuals search engine
changing a wheel..................................(up to the end of the DU)lifting the vehiclechanging a wheel ............................(up to the end of the DU)
5.11
ENG_UD10600_1Changement de roue (X85 - B85 - C85 - S85 - K85 - Renault)ENG_NU_853-3_BCSK85_Renault_5
Turn it a few times to lift the wheel off the ground.Undo the bolts and take off the wheel.Fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub.Tighten the bolts and lower the jack.With the wheel on the ground, fully tighten the bolts and check they are correctly tightened as quickly as possi- ble (tightening torque 110 Nm).
Changing a wheel
If you have a puncture, re- place the wheel as soon as possible.
A tyre which has been punc- tured should always be inspected (and repaired, where possible) by a specialist.
Switch on the hazard warn- ing lights.
Keep the vehicle away from traffic and on a level sur- face where it will not slip (if neces- sary, place a solid support under the jack base).
Apply the hand brake and engage a gear (first or reverse, or P for auto- matic transmissions).
Ask all the passengers to leave the vehicle and keep them away from traffic.
CHANGING A WHEEL
A
5
4
3
2
1
Anti-theft bolt
If you use anti-theft bolts, fit these nearest the valve (otherwise it may not be possible to fit the wheel trim).
If necessary, remove the wheel trim.Depending on the vehicle, position adapter 1 on the wheel bolt.Use the wheelbrace to slacken off the
wheel bolts 2. Position it so as to be able to push from above.
Crank up jack 3 by hand to position the
jack head against jacking point 4 clos- est to the wheel concerned and, de- pending on the vehicle, marked by an
arrow 5.Continue to crank the jack so that the baseplate is correctly positioned (it should be underneath the vehicle and
aligned with jack head A).