oil level RENAULT CLIO CUP 2013 X85 / 3.G User Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2013, Model line: CLIO CUP, Model: RENAULT CLIO CUP 2013 X85 / 3.GPages: 35, PDF Size: 2.68 MB
Page 15 of 35
Downloaded from www.Manualslib.com manuals search engine 98CUP_2013 Release
C-15
Engine diagnostic parameters
: (see also chapter
C-Engine)
Engine
parameters Signification
Values expected
when engine is
OFF
Values expected when Engine is
running
RPM Engine revs 0 - Idle > 1200rpm
- WaterT<50°c : RPM limiter = 4500rpm
- 50°c
progressively to reach 3500rpm at 120°c
VBatt (V) Battery voltage 11.5V to 12.5V > 13.5V
OilP (b) Oil pressure 0 >1.5b when engine RPM>3000
WaterT (°C) Water temp
#ambient temp when the
car is cold Water temp progressively increase to 87°c
(Water fan goes ON at low speed)
AirT (°C) Air intake temp #ambient temp when the
car is cold Air temp progressively increase when the car is
in static position
Pedal (%) Gas Pedal
potentiometer position 0 > 100% depending on
Gas pedal position 0 > 100% depending on Gas pedal position
Throttle (°) Throttle
potentiometer position <9°
(depends on water temp) 0> 100° depending on Gas pedal position
FBW Fly by wire status OK
OK
Manifold P Manifold air pressure Atmospheric pressure - Idle : Manifold P< 350mb
- When Water T >55°c Manifold P follows strictly
the BoostP (at 100% throttle)
Boost P Boost pressure Atmospheric pressure - Boost P < 1.1b when Water T <30°c
- When 30°c < Water T < 50°c => BoostP
increase progressively
- when water T > 50°c => BoostP can go to its
maximum value (2.1b)
VVT1_tg (°)
VVT1 target =
instruction sent by
ECU to the dephaser 0
If WaterT < 55°, VVT1_tg =0
As soon as WaterT>55°, VVT1_tg=100
VVT1_pos (°) Intake
camshaft pos :
depends on VVT1_tg 0 - After starting : automatic calibration (10sec)
- Then VVT1_pos = 100°
- when water T>55°, VVT1_pos must strictly
follows VVT1_tg
Fuel (L) Fuel level Fuel Level Fuel level
Fuel LP (b)
Fuel press
(measured at the
exit of the fuel cell) 0b / 5b maxi when “fuel
pump” button is pressed 4.7
-If fuel HP < 15b during starter excitation, the
engine will not start, it’s necessary to bleed the
air inside of the rail
(see procedure in chapter
C-Engine)
Water Fan Water fan speed OFF
(depends on water temp) LOW (Low speed) when Water T >87°C
OFF when Water T <86°C
HIGH (High speed) when Water T >90°C
LOW when WaterT <88°C
See chapter
C-Engine
Turbo Fan Turbo fan OFF
(depends on Air temp) ON if Air temp is > 50°C
OFF when Air temp is <48°C
Waste Gate (%)
Waste gate duty 0
Depends on Boost pressure target
Must always be under 70%
Pop off (%) Pop off valve pos 0 (close) - 100% (open) after an complete closure of the
throttle and Boost P > 1400 mbar (to reduce the
pressure upstream to the closed throttle)
- 100% if WaterT <50°c
ID Not used
For reliability reasons and to avoid alarms risings,
it’s strongly
recommended to let the engine warm up to a water temp > 60°C
before any practising. If this condition is not respec ted, the full engine
power won’t be available.