wiring RENAULT CLIO CUP 2013 X85 / 3.G User Manual

Downloaded from www.Manualslib.com manuals search engine 98CUP_2013 Release

C-11

B.6.2 STEERING WHEEL SWITCH PANEL : XAP_STER98



Button Action Short press Long press
LIGHT Light management
(Front headlight and rear) Head light flasher 1st Long press :
light goes ON
2nd long press : light goes OFF
WIPER Wiper management 1 go/back wiper, return to
“0” position 1st Long press :
permanent wiper on only
one constant speed (maximum speed)
2nd long press : wiper stops and returns
at “0” position
CLEAN Windscreen cleaning (wiper + pump) While this push button is pressed, wiper and windsc
reen washer work
together. When released, wiper return to “0” positi on
PAGE Access to the dashboard
pages Change page
Switch between “diagnostic pages”
(3) and “driver pages” (5)
PIT Pit limiter management 1st short press :
enable (60kph)
2nd short press : Disable /
GEAR Gearbox barrel unlocking
(safety) Unlock the gearbox barrel (see
chapter
D “Trasnmission-sifting” ) /
GREEN
BUTTON Free button Management accessible using the
free connector on chassis loom (See
chapter
F “wiring looms”) /

Downloaded from www.Manualslib.com manuals search engine 98CUP_2013 Release

C-17

B.6.3.1.6 DIAGNOSTIC PAGE 3 : BRAKE / CHASSIS DIAGNOSTIC



Brake/
chassis
parameters
Signification
Values expected
when engine is
OFF
Values expected when Engine is
running
Front BP Font brake pressure From 0 to more than 10 0b
Rear BP Rear Brake pressure From 0 to 40b (depends on rear brake pressure limiter setup)
Balance % of brake pressure
on front axle From 40% to 70% (depends on balance bar rod setup)
Steering
Steering angle
sensor -360° to + 360°
FL WSP (kph)
Front left wheel
speed 0 >0 when a gear is engaged
FR WSP (kph)
Front right wheel
speed 0 >0 when a gear is engaged

B.6.3.1.7
DIAGNOSTIC PAGE 4 : CBNT DIAGNOSTIC (PAGE 1/2 : STATUS)



Every indication corresponds to the XAP CBNT pinout and shows the status
(OK / FAULT)
of each Pin (one Letter = A, B, h, g…etc = 1 Pin). All values must be “OK” (green).
When “FAULT” appears, the Pin is not correctly supp lied. Please refer to chapter F- wiring
for more details.

Downloaded from www.Manualslib.com manuals search engine 98CUP_2013 Release

C-18

B.6.3.1.8 DIAGNOSTIC PAGE 5 : CBNT DIAGNOSTIC (PAGE 1/2 : STATES)



Every indication corresponds to the XAP CBNT pinout and shows the state
(ON/OFF) of
each Pin. Please refer to chapter F- wiring for more details.

When XAP Master relay is ON :
- All values from the first column must be “ON” (gr een)

- On the second column, Steer W/A, starter and revG B Sol must be “ON” green, for the
other Pins, please find the action/result below :
Sensors
/actuators Signification Action result
stop light SW Brake Pedal
contactor switch Brake pedal pressed OFF >ON
rain light SW Rain light switch on facia switch
panel “Rain ” switch ON OFF >ON
light left SW Left side lights switch on steering
wheel “light” button pressed OFF >ON
light right SW Right side lights switch on steering
wheel “light” button pressed OFF >ON
ignition Ignition coils switch on facia switch
panel “ignition” switch ON OFF >ON
fuel pump Fuel tower pump (facia switch panel
manual mode or automatic mode) state “fuel pump” button pressed and/or
automatic fuel pump management OFF >ON
brake light Lateral rear brake light state
Brake pedal pressed OFF >ON
rain light** Rear central rain light state Brake pedal pressed
And/or « Rain » switch ON And/or pit limiter ON
And/or Reverse gear ratio engaged OFF >ON
wiper zero “Wiper” position state
When “wiper” leave its rest position ON>OFF

** Please refer to Central rear rain light activati on strategies in this chapter

Downloaded from www.Manualslib.com manuals search engine 98CUP_2013 Release

C-30

You must fit the wiring of the white connector directly on the plastic windscreen lower
grid using a tyrap® as indicated below:



The fire extinguisher is controlled by a deported c ontrol unit fitted on the central tunnel.
A specific fire extinguisher loom allows to link th is control unit + fire extinguisher to the
chassis loom.

Position 1: system isolated

This position is to test the extinguisher loom. Eve rything must be correctly connected to
the loom. When you push the fire button (Facia swit ch panel or from outside deported
button), the green light must go ON but the extinguisher will n ot deploy.


NOTE :
if the green light is ON without testing the syste m, there is a default on the
loom. In this case, you must be careful because the extinguisher is directly connected to
the command box. As a consequence, if you switch to position 3, you will immediately
deploy the extinguisher.
Position 2: battery check


If the orange light goes ON, the battery is ok.
Position 3: system armed


“System armed” means that if you push the fire butt on (Facia switch panel or from
outside deported button), you will immediately depl oy the extinguisher.
The green light goes ON only when the extinguisher is deployed.
3
1
2 deported
control unit