change time RENAULT CLIO SPORT TOURER 2012 X85 / 3.G Owners Manual

1.68
ENG_UD26845_2
Ordinateur de bord : paramètres de voyage (X85 - B85 - C85 - S85 - K\
85 - Renault)
ENG_NU_853-8_BCSK85_Renault_1
Jaune NoirNoir texte
ON-BOARD COMPUTER: trip settings (3/4)
Examples of display selections
by pressing button 2 Interpreting the display selected
Display A Display Bc) Distance before service
Distance remaining until the next service.
There are several scenarios:
–
remaining mileage less than 900 miles (1,500 km) or next serv-
ice due within two months. When the display selected is “mile-
age before service”, symbol
Ê appears on display A . The
message “Service due” appears on display B.
– mileage before service equal to 0 miles/km or date of serviced
reached. When the display selected is “mileage before service”,
symbol
Ê flashes on display A accompanied by warning light
©. The message “Service vehicle” is shown on display B
accompanied by the symbol
Ê and warning light ©.
12000 SERVICE DUE IN

KMÊ12000 KM
NB: depending on the vehicle, the mileage before service changes according to the driving style (frequent driving at low speed,
door-to-door journeys, extensive use at idle speed, towing a trailer etc.). The distance remaining until the next service can there-
fore decrease more quickly in some cases than the actual distance travel\
led.
Resetting the display after the service in accordance with the maintenan\
ce schedule.
The mileage before service must only be reset after a service which complies with the recommendations in the maintenance
schedule.
If you decide to change the oil more frequently, do not reset this data each time the oil is changed to avoid exceeding the replace -
ment intervals for other parts in the maintenance schedule.
Special note: to reset the distance before service, press and hold one of the display reset buttons for approximately 10 seconds
until the display shows the mileage permanently.
The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT \
AND COUNTRY.

clock ..................................................... (up to the end of the DU)
clock ..................................................... (up to the end of the DU)
control instruments ............................... (up to the end of the DU)
1.73
ENG_UD24926_3
Heure et température extérieure (X85 - B85 - C85 - S85 - K85 - Re\
nault)
ENG_NU_853-8_BCSK85_Renault_1
Clock and exterior temperature
Then press and hold button 3 to con -
firm the time set.
The minutes flash; repeatedly press or
press and hold button 2 to set them.
When setting is complete, the hours
and minutes remain displayed continu -
ously for 2 seconds: your setting is reg-
istered.
You may change the display.Display A
The time is displayed when the ignition
is switched on.
To access display 1 for setting the time,
press button 2 or 3. Wait for a few sec-
onds.
The hours and minutes flash and you
are now in setting mode; press and
hold button 3 to set the hours.
When the hours flash, repeatedly press
or press and hold button 2, to set them.
CLOCK AND EXTERIOR TEMPERATURE (1/2)
2
3
If the power supply is cut (battery
disconnected, supply wire cut, etc.),
the clock must be reset.
We recommend that you do not
adjust these settings while driving.
TIME
16:30
1
3382.3

KM
16:20
A

wipers ................................................... (up to the end of the DU)
windscreen washer ............................... (up to the end of the DU)
1.83
ENG_UD19811_2
Essuie-vitre / lave-vitre avant (X85 - B85 - C85 - S85 - K85 - Renault)\
ENG_NU_853-8_BCSK85_Renault_1
Wash/Wipe
Vehicles with automatic wiper
function
With the engine running, move stalk 1
– A park.
– B automatic wiper function
When this position is selected, the
system detects the presence of
water on the windscreen and triggers
wiping at a suitable wiping speed.
It is possible to modify the sensitivity
by turning ring 2.
– C normal wiping speed.
– D fast wiping speed.
Special note
When the vehicle is being driven, the
wiping speed slows down whenever the
vehicle stops. The speed will change
from fast wiping speed to normal wiping
speed.
As soon as the vehicle moves off,
wiping will return to the speed originally
selected.
Any action on stalk 1 overrides and
cancels automatic operation.
With the ignition on,
move stalk 1
– A park.
– B intermittent wiping
The wipers will pause for several
seconds between sweeps. It is pos-
sible to change the time between
sweeps by turning ring 2.
– C normal wiping speed.
– D fast wiping speed.
WINDSCREEN WASH/WIPE (1/2)
A
B
C
D
121
When working in the engine
compartment, ensure that
the windscreen wiper stalk
is in position A (park).
Risk of injury.

JauneNoirNoir texte
2.29
ENG_UD22304_2
Régulateur-limiteur de vitesses : fonction régulateur (X85 - B85 \
- C85 - S85 - K85 - Renault)
ENG_NU_853-8_BCSK85_Renault_2
CRUISE CONTROL/SPEED LIMITER: cruise control function (3/4)
Exceeding the cruising speed
In the event of an emergency
The cruising speed may be exceeded
at any time by depressing the accelera -
tor pedal. While it is being exceeded,
the cruising speed flashes on the in -
strument panel.
Cruising speed cannot be main -
tained
In some driving conditions (for exam -
ple when driving down a steep gradi -
ent), the system is unable to maintain
the cruising speed: the speed on the in-
strument panel information display will
flash to inform you of this situation.
Varying the cruising speed
The cruising speed may be changed by
pressing repeatedly or continuously on:
– switch 2 (+) to increase the speed;
– switch 3 (-) to decrease the speed.
The cruise control function
is in no way linked to the
braking system.
23

automatic gearbox (use) ....................... (up to the end of the DU)
changing gear ....................................... (up to the end of the DU)
driving ................................................... (up to the end of the DU)
automatic gearbox selector lever ..........(up to the end of the DU)
2.31
ENG_UD12577_2
Boîte automatique (X85 - B85 - C85 - S85 - K85 - Renault)
ENG_NU_853-8_BCSK85_Renault_2
Automatic gearbox
Operation
With gear lever 1 in position P, start the
engine.
With your foot on the brake pedal (warn-
ing light 4 goes out), move the lever out
of position P.
Only engage D or R when the vehi -
cle is stopped, with your foot on the
brake and the accelerator pedal re -
leased.
You must apply the brake before
pressing unlocking button 2 to move
out of position P.
Selector lever 1
P: park
R: reverse
N: neutral
D: automatic mode
3: displays gear engaged in manual
mode.
AUTOMATIC TRANSMISSION (1/3)
1
3
Driving in automatic mode
Move lever 1 to position D.
In most traffic conditions, you will not
have to touch the gear selector lever
again: the gears will change automati -
cally at the right time and at the most
suitable engine speed because the au-
tomatic system takes into account the
vehicle load and road contour and ad-
justs itself to the particular driving style
you have chosen.
Economical driving
When driving, always leave the lever
in position D, keeping the accelerator
pedal lightly depressed to ensure au -
tomatic gear changes at comparatively
low engine speeds.
Accelerating and overtaking
Depress the accelerator pedal firmly
and fully (so that it goes beyond the
kickdown point).
This will enable you to change down
to the optimum gear within the
engine range.
4
2

JauneNoirNoir texte
3.19
ENG_UD14664_3
Lève-vitres électriques / Lève-vitres impulsionnels / Lève-v\
itres manuels (X85 - B85 - C85 - S85 - K85 - Renault)
ENG_NU_853-8_BCSK85_Renault_3
eLeCtriC WinDOWs (3/3)/ManUaL WinDOWs
One-touch mode
– Briefly press the relevant switch
fully: the window is lowered com -
pletely.
– Briefly lift the relevant switch fully:
the window is raised completely.
Pressing the switch again while the
window is moving will stop its move -
ment.
special note
For your safety your vehicle is fitted
with an anti-pinch facility. When a
window encounters resistance whilst
closing (someone’s fingers, an animal’s
paw or the branch of a tree, for exam-
ple), it stops and lowers by several cen-
timetres.
Once the obstacle has been removed,
briefly lift the switch again fully to close
the window.
normal mode
– Press the relevant switch to lower
the window and release it when the
window is at the required height.
– Lift the relevant switch to raise the
window and release it when the
window is at the required height.
Operating faults
If a window does not close, the system
will change to normal mode: lift the rel-
evant switch as many times as neces-
sary to close the window, then release
it. Press the switch again (still on the
closing side) for one second to reset
the system.
If necessary, contact an approved
Dealer.
Manual window winder
controls
Turn handle 1.
1
Closing windows can cause
serious injury.

maintenance:mechanical ...................................... (up to the end of the DU)
engine oil level ...................................... (up to the end of the DU)
engine oil .............................................. (up to the end of the DU)
4.4
ENG_UD22490_3
Niveau huile moteur : généralités (X85 - B85 - C85 - S85 - K85\
- Renault)
ENG_NU_853-8_BCSK85_Renault_4
Jaune NoirNoir texte
Variant 1 Variant 2Interpretation of messages
25302Message 1
“Oil level OK”
OIL LEVEL
OOOOOOO
The message “oil” is
displayed, alternating with dashes No display
Message 2
“Adjust oil level”
If the level is at minimum: depending
on the vehicle, the message “top up oil
level” or “oil” appears on the display, al-
ternating with dashes and the
©
warning light on the instrument panel
comes on: message 2.
It is vital to top up the oil as soon as
possible.
Engine oil level: general information
The display only warns the
driver if the oil level is at the
minimum level. It does not
inform the driver that the oil
level has exceeded the maximum
level as this can only be measured
using a dipstick.
Minimum oil level warning on instru-
ment panel
When the ignition is switched on, if the
level is above the minimum level, the
message “oil ok” or “oil level correct” is
shown on the display for approximately
15 seconds.
For more information, press the trip
computer readout button: the message
“oil level” will be shown on the display
with squares which are replaced by
dashes when the level drops.
To advance to trip computer reading,
press the button again.
It is normal for an engine to use oil for
lubrication and cooling of moving parts
and it is normal to top up the level be-
tween oil changes.
However, contact your approved
Dealer if more than 0.5 litres is being
consumed every 600 miles (1,000 km)
after the running in period.
Check the oil level at regular inter
-
vals and before any long journey
to avoid the risk of damaging your
engine.
Reading the oil level
The oil level should be read with the ve-
hicle on level ground, after the engine
has been switched off for some time.
The dipstick must be used to read
the exact oil level and make sure
that the maximum level has not been
exceeded (risk of engine damage).
Refer to the following pages.
The instrument panel display only
alerts the driver when the oil level is at
its minimum.
ENGINE OIL LEVEL: general information (1/2)

changing a wheel.................................. (up to the end of the DU)
lifting the vehicle changing a wheel ............................ (up to the end of the DU)
5.11
ENG_UD19793_3
Changement de roue (X85 - B85 - C85 - S85 - K85 - Renault)
ENG_NU_853-8_BCSK85_Renault_5
Continue to crank the jack so that the
baseplate is correctly positioned (it
should be underneath the vehicle and
aligned with jack head A).
Turn it a few times to lift the wheel off
the ground.
Changing a wheel
Switch on the hazard warn-
ing lights.
Keep the vehicle away from
traffic and on a level sur -
face where it will not slip (if neces -
sary, place a solid support under the
jack base).
Apply the hand brake and engage a
gear (first or reverse, or P for auto-
matic transmissions).
Ask all the passengers to leave the
vehicle and keep them away from
traffic.
CHANGING A WHEEL (1/2)
A
54
3
2
1
Vehicles equipped with a jack
and wheelbrace
If necessary, remove the wheel trim.
Depending on the vehicle, position
adapter 1 on the wheel bolt.
Use the wheelbrace to slacken off the
wheel bolts 2 . Position it so as to be
able to push from above.
Crank up jack 3 by hand to position the
jack head against jacking point 4 clos-
est to the wheel concerned and, de -
pending on the vehicle, marked by an
arrow 5.
To prevent any risk of injury
or damage to the vehicle,
only crank the jack until the
wheel you are replacing is
a maximum of 3 centimetres off the
ground.
If the vehicle is not equipped with a
jack or wheelbrace, you can obtain
these from your approved dealer.