Heating RENAULT KANGOO 2013 X61 / 2.G Diesel DCM 1.2 Injection User Guide

13B-50
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF021
PRESENT
OR
STOREDPREHEATING WARNING LIGHT CIRCUIT
CO.0: Open circuit or short circuit to earth
CC.1: Short circuit to + 12 V
NOTESSpecial notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Clear the fault and check the correct operation of the warning light with command AC060 Preheating warning
light.
Check the connection and condition of the connector for the preheating warning light sensor, component code
247.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 9804A, Electrical wiring repair,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation and continuity of the following connection:
•3NX between components 247 and 120.
If the connection is faulty and if there is a repair procedure (see Technical Note 9804A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the instrument panel, component code 247 (see MR 388, (Logan/Sandero), MR
423 (Thalia 2/Symbol 2), MR 451 (Duster) or MR 374 (Kangoo VLL), Mechanical, 83A, Instrument panel,
Instrument panel: Removal - Refitting).
If the fault persists, contact your Techline.
DCM1.2_V08_DF021

13B-53
AFTER REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$071.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF025
PRESENT
OR
STOREDPRE-POSTHEATING UNIT DIAGNOSTIC LINE
CO: Open circuit.
NOTESSpecial notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Check power supply fuse F1 (70 A) or F6 (for Kangoo VLL) of the preheating unit, component code 257 in the
engine compartment (see MR 388 (Logan/Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2) or MR 374
(Kangoo VLL), Mechanical, 81C, Fuses, Fuses: List and location of components).
Check the connection and condition of the heater plug connectors, component codes 680, 681, 682, and 683.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Measure the resistance of each heater plug.
The resistance must be less than 2 .
Replace the faulty plug(s) (see MR 388 (Logan/Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2) or MR
374 (Kangoo VLL), Mechanical, 13C, Preheating, Heater plugs: Removal – Refitting).
Check the connection and condition of the preheating unit connector, component code 257.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the connection and condition of the injection computer connector, component code 120.
If the connector is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation, continuity and the absence of interference resistance on the following connections:
●3FY between components120 and 257,
●3FF between components120 and 257.
If the connection(s) are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or
Technical Note 9804A (Dacia), Repairing electrical wiring, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If the fault is still present, contact the Techline.
DCM1.2_V08_DF025

13B-101
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF162
PRESENT
OR
STOREDOVERHEATING WARNING LIGHT
CO.0: open circuit or short-circuit to earth
CC.1: short circuit to +12 V
NOTESSpecial notes:
Use the Wiring Diagrams Technical Note for Logan, Sandero, Duster, Thalia 2/
Symbol 2 or Kangoo VLL.
Clear the fault and check the correct operation of the warning light with command AC061 Overheating warning
light.
Check the connection and condition of the connector for the overheating warning light sensor, component code
247.
Check the connection and condition of the injection computer connector, component code 120.
If the connectors are faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the connector, otherwise
replace the wiring.
Check the insulation and continuity of the following connection:
•31A between components 247 and 120
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
If the fault is still present, replace the instrument panel, component code 247 (see MR 388, (Logan/Sandero), MR
423 (Thalia 2/Symbol 2), MR 451 (Duster) or MR 374 (Kangoo VLL), Mechanical, 83A, Instrument panel,
Instrument panel: Removal - Refitting).
If the fault persists, contact your Techline.
DCM1.2_V08_DF162

13B-103
AFTER
REPAIRDeal with any faults declared by the diagnostic tool.
Clear the computer memory.
Carry out a road test followed by another check with the diagnostic tool.
V1 MR-376-X76-13B000$072.mif
DIESEL INJECTION
Fault finding – Interpretation of faults13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
DF195
CONTINUED
Measure the resistance of the camshaft sensor, component code 746 between connections 3PL (or 3DRC) and
3CQ (or 3DRB).
If the resistance of the camshaft sensor is not between 9737.5  < X < 10,762.5 , replace the sensor (see MR
388 (Logan/Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2) or MR 374 (Kangoo VLL), Mechanical,
13B, Diesel injection, Camshaft position sensor: Removal – Refitting).
Check that the engine earthing is in order (oxidation, tightness, etc.).
Check the mounting, the air gap and the condition of the engine speed sensor (heating).
Check the timing adjustment (see MR 388 (Logan/Sandero), MR 451 (Duster), MR 423 (Thalia 2/Symbol 2) or
MR 374 (Kangoo VLL), Mechanical, 11A, Top and front of engine, Timing belt: Removal - Refitting).
If the fault is still present, contact the Techline.

13B-120V1 MR-376-X76-13B000$080.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
STATUS CHECK (CONTINUED 1)
NOTESOnly perform this conformity check after a thorough check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine stopped, ignition on.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Air
conditioningET116:Climate control
authorisationNO
YES: The UCH should send an
activation request to the injection.
The coolant pressure sensor must
not be defective. Satisfactory engine
operating conditions (coolant
temperature, engine load etc.).
NO: One of the above conditions has
not been fulfilled.NONE
EGRET008:EGR solenoid
valve controlINACTIVE
Shows the condition of the EGR
valve control.
INACTIVE: The valve is not
controlled by the computer.
ACTIVE: The valve is controlled by
the computer.NONE
PreheatingET007:Pre-
postheating
controlACTIVE/INACTIVE
Shows the status of the preheating
unit control.In the event of a fault,
consult the interpretation
of fault DF017 Preheating
unit control circuit.

13B-128V1 MR-376-X76-13B000$080.mif
DIESEL INJECTION
Fault finding – Conformity check13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
STATUS CHECK (CONTINUED 1)
NOTESOnly perform this conformity check after a complete check using the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine idling, warm engine, coolant temperature > 80°C.
FunctionParameter or status
checked or actionDisplay and notes Fault finding
Air
conditioningET116:Climate control
authorisationNO
YES: The UCH should send an
activation request to the injection.
The coolant pressure sensor must
not be defective. Satisfactory engine
operating conditions (coolant
temperature, engine load etc.).
NO: One of the above conditions has
not been fulfilled.NONE
EGRET008:EGR solenoid
valve controlINACTIVE
Shows the condition of the EGR
valve control.
INACTIVE: The valve is not
controlled by the computer.
ACTIVE: The valve is controlled by
the computer.In the event of a fault,
apply the interpretation of
faults DF016 EGR control
circuit and DF114 EGR
solenoid valve circuit
(not applicable to K9K796
Euro 2).
PreheatingET007:Pre-
postheating
controlACTIVE/INACTIVE
Shows the status of the preheating
unit control.In the event of a fault,
consult the interpretation
of fault DF017 Preheating
unit control circuit.

13B-135V1 MR-376-X76-13B000$090.mif
13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
Tool Status Diagnostic tool title
ET003Engine immobiliser
ET007Pre-postheating control
ET008EGR solenoid valve control (not applicable to K9K796 Euro 2)
ET023Fast idle speed request
ET038Engine
ET039Brake pedal
ET116Climate control authorisation
ET122Brake switch no. 1 signal
ET123Brake switch no. 2 signal
ET164Configuration with air conditioning
ET200Fuel flow controller
ET227Key
ET233Clutch pedal
ET432Wastegate regulation
ET563Flow capacity function
ET637New pump chamber filling
DIESEL INJECTION
Fault finding – Status summary table

13B-145V1 MR-376-X76-13B000$130.mif
13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
Tool command Diagnostic tool title Comments
RZ001Fault memoryThis command is used for clearing the computer's stored
faults
RZ002EGR programming adaptivesUse this command when replacing the EGR valve (not
applicable to K9K796 Euro 2).
RZ004Pressure regulation adaptivesUse this command when simultaneously replacing the four
injectors and after replacing/retightening the accelerometer.
It enables you to reset the injector adaptives.
RZ005ProgrammingThis command enables you to reinitialise the entire computer
configuration.
AC001Preheating unitActivating this controls the preheating unit to test the heater
plug supply.
AC002EGR solenoid valveActivating this enables an audible check of the mechanical
operation of the EGR valve (not applicable to K9K796
Euro 2).
AC004Turbocharging solenoid valveActivating this enables an audible check of the operation of
the turbocharging solenoid valve.
AC005Cylinder 1 injectorActivating this enables an audible check of the injector on
cylinder 1.
AC006Cylinder 2 injectorRunning this allows you to you listen to the injector on
cylinder 2 when operating.
AC007Cylinder 3 injectorActivating this enables an audible check of the injector on
cylinder 3.
AC008Cylinder 4 injectorActivating this enables an audible check of the injector on
cylinder 4.
AC010High pressure pumpActivating this lets you listen to the operation of the high-
pressure pump.
AC028Static testActivating this enables fault finding to be run on the EGR,
high pressure pump and water in fuel warning light circuits
DIESEL INJECTION
Fault finding – Command summary table

13B-146V1 MR-376-X76-13B000$130.mif
DIESEL INJECTION
Fault finding – Command summary table13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
Tool
commandDiagnostic tool title Comments
AC029 High pressure circuit sealing testActivating this will request the injection system to detect a
leak on the high pressure circuit after a procedure has been
carried out. This is activated with the engine warm and
running and consists of unladen acceleration repeated 4
times.
AC056 Power-assisted steering
assembly relayActivating this actuates the power assisted steering pump.
AC060 Preheating warning lightActivating this actuates the preheating warning light on the
instrument panel.
AC061 Overheating warning light.Activating this actuates the engine overheating warning light
on the instrument panel.
AC068Injection fault warning light.Activating this actuates the injection fault warning light on
the instrument panel.
AC099Deactivation of electrical
consumersThis activation only deactivates the preheating function.
AC100End deactivation of electrical
consumersActivating this enables preheating to be authorised after the
injection computer has been programmed or reprogrammed
(see Replacement of components).
AC153 High-speed fan assemblyActivating this actuates the high speed fan relay to test the
supply to the high speed fan.
AC154 Fan low speed.Activating this actuates the low speed fan relay to test the
supply to the low speed fan.
AC155MIL warning lightThis activation controls the malfunction indicator light on the
instrument panel (emission control/EOBD warning light).
AC180 Air conditioning compressor
relay control.Activating this enables you to listen to the operation of the
air conditioning compressor.
AC212 New pump chamber fillingThis must only be activated after the high pressure pump
has been replaced (see Replacement of components).
This command is used to activate the pump repriming
sequence.
AC250 Heating resistor 1 relay.Activating this controls the heating resistor no. 1 relay to test
the heating resistor supply.

13B-147V1 MR-376-X76-13B000$130.mif
DIESEL INJECTION
Fault finding – Command summary table13B
DCM 1.2 Injection
Program no.: 4C
Vdiag No.: 08
Tool
commandDiagnostic tool title Comments
AC251 Heating resistor 2 relay.Activating this controls the heating resistor no. 2 relay to test
the heating resistor supply.
AC252 Heating resistor 3 relay.Activating this controls the heating resistor no. 3 relay to test
the heating resistor supply.
AC261 Water in fuel warning lightActivating this actuates the water present in fuel warning
light; this warning light is located on the instrument panel, if
fitted to the vehicle.
SC001 Write saved dataUse this command after replacing or (re)programming the
computer (if the data were saved using command SC003
Save computer data).
SC002 Enter injector codesThis command enables you to manually write the calibration
code marked on the injectors. Run this command after
replacing the injectors.
SC003 Save computer dataThis command saves the computer operating data, C2I
(individual injector correction) parameters and engine
programming adapters. Run this command before replacing
or (re)programming the computer.