System reset RENAULT MEGANE 2005 X84 / 2.G Owners Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2005, Model line: MEGANE, Model: RENAULT MEGANE 2005 X84 / 2.GPages: 250, PDF Size: 5.72 MB
Page 52 of 250
Downloaded from www.Manualslib.com manuals search engine
1
NU761_2_G1-FRA.qxd 10/11/05 15:53 Page 1.42
1.42
The passenger airbag
must only be deactivated
or activated when the
vehicle is stationary.
If the lock is moved when the
vehicle is moving, warning lights
åand come on: the
passenger airbag is deactivated.
Switch the ignition off then on
again to reset the airbag in
accordance with the lock.
CHILD SAFETY (continued)
Activating the front passenger
airbags
You should reactivate the airbag as
soon as you remove the child seat
from the front passenger seat, to
ensure the protection of the front
passenger in the event of an impact. Operating faults
It is forbidden to fit a rear-facing
child seat to the front passenger seat
if the airbag activation/deactivation
system is faulty.
Allowing any other passenger to sit
in that seat is not recommended.
Consult your RENAULT Dealer as
soon as possible.
To reactivate the airbags:
push and
turn lock 1to the ON position.
After switching on the ignition
again, check that the
ãwarning
light is off.
The means of restraint which are
additional to the front passenger
seat belt and anti-slide airbag (for
the three-door version) are
activated.
NU761_2_G1-ENG.qxp 1/6/2006 12:23 PM Page 1.42 (Black plate)
Page 77 of 250
Downloaded from www.Manualslib.com manuals search engine
2
NU761_2_G1-FRA.qxd 10/11/05 15:54 Page 1.67
1.67
TRIP COMPUTER AND WARNING SYSTEM (continued)
Trip mileage recorder reset
button
To reset the trip mileage recorder,
select the Trip mileage recorder
display, then press key 2until the
recorder is reset.
Resetting of the journey
parameters
With one of the trip parameters
selected on the display, press
button 2 until the display is reset.
Interpreting some of the values
displayed after resetting
The values showing average fuel
consumption, range and average
speed will become more stable and
reliable the further you travel since
the last time the reset button was
pressed.
For the first few miles after pressing
the reset button you may notice:
that the range increases as you
travel.
This is normal; average fuel
consumption may decrease when:
- the vehicle stops accelerating,
- the engine reaches its operating temperature (engine cold when
reset button pressed),
- when you drive from a built up area on to the open road. that the average fuel consumption
increases when the vehicle is
stationary with the engine idling.
This is normal since the computer
takes account of fuel used during
idling.
Automatic resetting of the
journey parameters
A reset is automatic when the
maximum value for any of the
parameters is exceeded.
NU761_2_G1-ENG.qxp 1/6/2006 12:23 PM Page 1.67 (Black plate)
Page 78 of 250
Downloaded from www.Manualslib.com manuals search engine
23397
23398
23825
NU761_2_G1-FRA.qxd 10/11/05 15:54 Page 1.68
1.68
TRIP COMPUTER AND WARNING SYSTEM (continued)
Examples of selections Interpreting the display selecteda) Total mileage and trip mileage recorder.
b) Trip parametersFuel consumed since the last reset.
Average fuel consumption since the last reset.
This value is displayed after driving 400 metres and takes into account \
the
distance travelled and the fuel used since the last time the reset butto\
n was
pressed.
NU761_2_G1-ENG.qxp 1/6/2006 12:23 PM Page 1.68 (Black plate)
Page 79 of 250
Downloaded from www.Manualslib.com manuals search engine
23939
23402
23527
23826
NU761_2_G1-FRA.qxd 10/11/05 15:54 Page 1.69
1.69
TRIP COMPUTER AND WARNING SYSTEM (continued)
Examples of selections Interpreting the display selectedCurrent fuel consumption(depending on the vehicle)
This value is displayed after a speed of approximately 18 mph (30 km/h)\
is
reached.
Estimated range with remaining fuel
This range takes into account the average fuel consumption since the las\
t time
the reset button was pressed.
The value is displayed after driving 400 metres.
Distance travelled since last reset.
Average speed since the last reset.
The value is displayed after driving 400 metres.
NU761_2_G1-ENG.qxp 1/6/2006 12:23 PM Page 1.69 (Black plate)
Page 80 of 250
Downloaded from www.Manualslib.com manuals search engine
NU761_2_G1-FRA.qxd 10/11/05 15:54 Page 1.70
1.70
TRIP COMPUTER AND WARNING SYSTEM (continued)
Examples of selections Interpreting the display selectedc) Mileage before oil change/serviceDistance before the next service.
There are several scenarios:
remaining mileage less than 900 miles (1,500 km)or next service due within
two months. The SERVICE DUE message is displayed along with the
Ê
symbol on the trip computer (while Mileage before service is displayed,\
or
for 15 seconds).
mileage before service equal to 0 miles/km or date of service reached.
The message “SERVICE DUE” is displayed when the “mileage before oil
change” display is selected accompanied by the trip computer symbol
Ê
flashing continuously across all of the trip computer pages.
Resetting the display after service in accordance with the maintenance
schedule
The mileage before oil change/service must only be reset after a service\
in
accordance with the recommendations in the Warranty and Services booklet.
If you decide to change the oil more frequently, do not reset this data each
time the oil is changed. This prevents the replacement interval from bei\
ng
exceeded for other parts included in the maintenance schedule.
To reset the service distance display, press the reset button for about
10 seconds until the fixed service distance display appears.
NU761_2_G1-ENG.qxp 1/6/2006 12:23 PM Page 1.70 (Black plate)
Page 88 of 250
Downloaded from www.Manualslib.com manuals search engine
3
1
2
NU761_2_G1-FRA.qxd 10/11/05 15:55 Page 1.78
1.78
Exterior temperature
indicator
As ice formation is related
to exposure, local air
humidity and temperature, the
external temperature alone is not
sufficient to detect ice.
CLOCK AND OUTSIDE TEMPERATURE
Vehicles equipped with a
navigation system, a radio, etc.
For vehicles not equipped with
buttons 2and 3, refer to the specific
equipment manual for details on
these vehicles.
Exterior temperature indicator
Special note:
When the outside temperature is
–3°C to +3°C, the °C characters flash
(signalling a risk of ice on the road).
With the ignition on , the time and,
depending on the vehicle, the
temperature is displayed.
Setting the time 1
For vehicles equipped with these
functions, setting buttons 2and 3
are used to set the clock.
Press button 2to set the hours and
press button 3to set the minutes. If the electrical supply is cut
(battery disconnected, power
supply wire broken, etc.), the
clock will lose its time setting.
The clock must be reset.
We recommend that you do not
adjust these settings while
driving.
NU761_2_G1-ENG.qxp 1/6/2006 12:23 PM Page 1.78 (Black plate)