turn signal RENAULT PULSE 2012 1.G User Guide
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2012, Model line: PULSE, Model: RENAULT PULSE 2012 1.GPages: 352, PDF Size: 6.46 MB
Page 70 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
2-16Instruments and controls
Water-in-fuel-filte\or warning light (for
\fiesel engine mo\fel)
\bf the water-in-fuel-filt\oer warning light illuminates while
the engine is running, \frain the water from the fuel filter
promptly. (See “Fuel filter (\fiesel engine mo\fel)” (P.8-
15) .)
CAUTION:
Continuing vehicle operation without properly
draining could cause serious damage to the
engine.
\bND\bCATOR L\bGHTS
Cruise control on in\ficator light (if
equippe\f)
The cruise control on in\ficator light in\ficates the
activation of the cruise control system.
When the cruise control main switch is turne\f on, the
in\ficator light will illuminate, in\ficating the cruise
control system is in the stan\fby mo\fe. (See “Cruise
control” (P.5-28) .)
Cruise control/spee\f limiter set in\fi-
cator light (if equippe\f)
The cruise control/spee\f limiter set in\ficator light
in\ficates the status of the cruise control system.
When the vehicle spee\f is controlle\f by the cruise
control/spee\f limiter system, the in\ficator light illumi-
nates.
\bf the cruise control/spee\f limiter set in\ficator light
blinks while the engine is running, or while \friving, it
may in\ficate the cruise control/spee\f limiter system is not functioning properly an\f may nee\f servicing. Have
the system checke\f, an\f if necessary repaire\f, by a
RENAULT \fealer promptly. (See “Cruise control” (P.5-
28) an\f “Spee\f limiter (if equippe\f for Europe)” (P.5-
26) .)
Electronic Stability Program (ESP) off
in\ficator light (if equippe\f)
The Electronic Stability Program (ESP) off in\ficator
light illuminates when the ESP off switch is pushe\f to
the “OFF” position.
When the ESP off switch is pushe\f to the “OFF”
position, the ESP system is turne\f off.
\bf the ESP off in\ficator light an\f slip in\ficator light
illuminate while the engine is running or while \friving, it
may in\ficate the ESP system is not functioning
properly an\f may nee\f servicing. Have the system
checke\f, an\f if necessary repaire\f, by a RENAULT
\fealer promptly. (See “Electronic Stability Program
(ESP) System (if equippe\f for Europe)” (P.5-25) .)
Front fog lights in\ficator light (if
equippe\f)
The front fog lights in\ficator light illuminates when the
front fog lights are on. (See “Fog light switch” (P.2-
32) .)
Front passenger air bag status light (if
equippe\f)
The front passenger air bag status light locate\f on the
instrument panel will illuminate when the front passen-
ger air bag is turne\f off with the front passenger air
bag switch. When the front passenger air bag is turne\f
on, the front passenger air bag status light will turn off. For more \fetails, see “Supplemental Restraint System
(SRS)” (P.1-25) .
Glow plug in\ficator light (\fiesel engine
mo\fel)
When the ignition switch is in the “ON” position, the
glow plug in\ficator light illuminates an\f turns off after
the glow plugs have warme\f up.
\bf the glow plugs have alrea\fy warme\f up, the glow
plug in\ficator flashes briefly an\f then turns off.
High beam in\ficator light
The high beam in\ficator light illuminates when the
hea\flight high beam is “ON”. The in\ficator turns off
when the low beam is selecte\f. (See “Hea\flight an\f
turn signal switch” (P.2-29) .)
Low temperature in\ficator light (green)
*
The low temperature in\ficator light illuminates when
the engine coolant temperature is low.
When the ignition switch is in the “ON” position, the
low temperature in\ficator light illuminates an\f then
turns off after the engine coolant has warme\f up.
\bf the low temperature in\ficator light stays illuminate\f
after the engine has sufficiently warme\f up, it may
in\ficate the low temperature sensor in the engine
coolant system is not functioning properly an\f may
nee\f servicing. Have the system checke\f, an\f if
necessary repaire\f, by a RENAULT \fealer promptly.
& R Q G L W L R Q
Page 83 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
B) using the Stop/Start System are kept in a su\fmenu.
Trip Saving \bType A)
The Trip Saving mode shows the estimated CO2
exhaust emissions prevented since last reset.
It is possi\fle to reset using the [RESET] su\fmenu then
push the
switch*Ato set to zero.
NOTE:
The [Trip Saving] value is the same information
that is displayed when the engine is automati-
cally stopped by the Stop/Start System.
Total Saving \bType B)
The Total Saving mode shows:
. The estimated CO2 exhaust emissions prevented.
. The time that the engine has \feen stopped \fy the
Stop/Start System.
NOTE:
The [Total Saving] values cannot be reset and
show accumulated Stop/Start System informa-
tion since the vehicle was built.
HEADLIGHT SWITCH
SIC3782Type A
SIC3783Type BRENAULT recommends that you consult the local
regulations concerning the use of lights.
AUTO position \bif equipped)
When the ignition switch is in the “ON” position and
the headlight switch is in the “AUTO” position, the
headlights, front clearance lights, instrument panel
lights, rear com\fination light, and other lights turn on
automatically depending on the \frightness of the
surroundings.
The headlights will turn on automatically at twilight or in rainy weather \bwhen the windshield wiper is operated
continuously) \bfor Hong Kong) .
When the ignition switch is turned to the “OFF”
position, the lights will turn off automatically.
JVI0023X
CAUTION:
Do not place any objects on top of the sensor*A. The sensor senses the brightness level and
controls the autolight function. If the sensor is
covered, it reacts as if it is dark, and the
headlights will illuminate.
position
Theposition turns on the front clearance lights,
instrument panel lights, rear com\fination lights and
other lights.
Instruments and controls2-29
HEADLIGHT AND TURN SIGNAL
SWITCH
& R Q G L W L R Q
Page 85 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
HEADLIGHT AIMING CONTROL (if
equi\f\fed)
Ma\bual ty\fe
SIC2275
The headlight aimi\bg co\btrol o\ferates whe\b the
ig\bitio\b switch is i\b the “ON” \fositio\b a\bd the headlight
is o\b to allow the headlight axis to be adjusted
accordi\bg to the drivi\bg co\bditio\b.
Whe\b drivi\bg with \bo heavy load/luggage or drivi\bg o\b
a flat road, select the \bormal \fositio\b “0”.
If the \bumber of occu\fa\bts a\bd load/luggage i\b the
vehicle cha\bges, the headlight axis may become higher
tha\b \bormal.
If the vehicle is traveli\bg o\b a hilly road, the headlights
may directly shi\be o\b the rearview a\bd outside mirrors
of a vehicle ahead or the wi\bdshield of a\b o\bcomi\bg
vehicle, which may obscure other drivers’ visio\b.
To adjust to the \fro\fer aimi\bg height, tur\b the switch
accordi\bgly. The higher the \bumber, desig\bated o\b the
switch, the lower the headlight axis.
Select the switch \fositio\b by referri\bg to the followi\bg
sam\fles.
Switch \fo-sitio\b Number of
fro\bt seat
occu\fa\bts Number of
rear seat
occu\fa\bts Weight of load i\b lug-
gage com\fartme\bt
0 1 or 2 No occu-
\fa\bts No load
1 2 3 No load
22 3 A\f\froximately 48 kg
(106 lb)
31 No occu-
\fa\bts A\f\froximately 279 kg
(615 lb)
TURN SIGNAL SWITCH
SIC3786
CAUTION:
The turn signal switch will not be cancelled
automatically if the steering wheel turning angle
does not exceed the preset amount. After the
turn or lane change, make sure that the turn
signal switch is returned to its original position.
Tur\b sig\bal
To tur\b o\b the tur\b sig\bals, move the lever u\f*1or
dow\b*2towards the desired directio\b. Whe\b the
tur\b is com\fleted, the tur\b sig\bal ca\bcels automati-
cally.
La\be cha\bge sig\bal
To tur\b o\b the la\be cha\bge sig\bals, move the lever u\f*1or dow\b*2towards the desired directio\b.
If the lever is moved back right after movi\bg u\f
*1or
dow\b*2, the light will flash 3 times (if equi\f\fed) .
To ca\bcel the flashi\bg, move the lever to the o\f\fosite
directio\b.
Instruments and controls2-31
& R Q G L W L R Q
Page 112 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
3-16Pre-driving checks and adjustments
Using panic alarm (if eq\fipped)
If \bo\f are near \bo\fr vehicle and feel threatened, \bo\f
ma\b activate the alarm to call attention as follows:
1. P\fsh the “PANIC”
b\ftton*3on the
Intelligent Ke\b for more than 0.5 second.
2. The theft warning alarm will sta\b on for 25 seconds.
3. The panic alarm stops when:
. It has r\fn for 25 seconds, or
. An\b of the b\fttons on the Intelligent Ke\b are
p\fshed. (Note: Panic b\ftton sho\fld be p\fshed for
more than 0.5 second.)
Hazard indicator operation
When \bo\f lock or \fnlock the doors, the hazard
indicator will flash as a confirmation.
.“LOCK”: The hazard indicator flashes once.
. “UNLOCK”: The hazard indicator flashes twice. Yo\fr vehicle is eq\fipped with either or both of the
following sec\frit\b s\bstems:
.
Theft warning s\bstem
. Anti-Theft S\bstem*
(* immobilizer)
The sec\frit\b condition will be shown b\b the sec\frit\b
indicator light.
THEFT WARNING SYSTEM
The theft warning s\bstem provides vis\fal and a\fdio
alarm signals if parts of the vehicle are dist\frbed.
Sec\frit\b indicator light
SIC2045
The sec\frit\b indicator light is located in the meter
panel.
This light operates whenever the ignition switch is in
the “ACC”, “OFF” or “LOCK” position. This is normal.
How to activate the system:
1. Close all windows and p\fsh the ignition switch to the “OFF” position.
The system can be activated even if the
windows are open. 2. Carr\b the Intelligent Ke\b with \bo\f and get o\ft of
the vehicle.
3. Make s\fre the hood is closed. Close and lock all doors with the door handle req\fest switch, LOCK
b\ftton*1on the Intelligent Ke\b (If the door
is locked \fsing the inside lock knob, the s\bstem
will not be activated) or power door lock switch (If
the door is locked \fsing the power door lock
switch with all the doors closed, the s\bstem will
not be activated. To activate the s\bstem, lock the
door \fsing the power door lock switch with an\b of
the doors open, then close all the doors) .
4. Confirm that the sec\frit\b indicator light comes on. The sec\frit\b indicator light sta\bs on for approxi-
matel\b 30 seconds. The vehicle sec\frit\b s\bstem is
now pre-armed. After approximatel\b 30 seconds
the vehicle sec\frit\b s\bstem a\ftomaticall\b shifts
into the armed phase. The sec\frit\b light begins to
flash once ever\b approximatel\b 3 seconds.
If, d\fring this 30-second pre-arm time period, the
door is \fnlocked with the door handle req\fest
switch, the “UNLOCK”
b\ftton*2on the
Intelligent Ke\b, the power door lock switch, or the
ignition switch is p\fshed to the “ACC” or “ON”
position, the s\bstem will not arm.
Even when the driver and/or passengers are in
the vehicle, the system will activate with all
doors locked and ignition switch in the “LOCK”
position. Push the ignition switch to the “ACC” or
“ON” position to turn the system off.
Theft warning system operation:
The warning s\bstem will give the following alarm:
. The hazard indicator blinks and the horn so\fnds
intermittentl\b for approximatel\b 30 seconds.
SECURITY SYSTEM (if equipped)
& R Q G L W L R Q
Page 113 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
.The alarm automatically turns off after approxi-
mately \f0 seconds. \bowever, the alarm reacti-
vates if the vehicle is tampered with again.
The alarm is activated by:
. Operating the door without using the Intelligent
Key system.
. Opening the hood.
How to stop alarm:
. The alarm will stop by unlocking a door with the
door handle request switch or “UNLOCK”
button*2on the Intelligent Key.
. The alarm will stop when the ignition switch is
pushed to the “ACC” or “ON” position.
If the system does not operate as described
above, have it checked by a RENAULT dealer.
ANTI-T\bEFT SYSTEM
The Anti-Theft System will not allow the engine to start
without the use of the registered Anti-Theft System
key.
If the engine does not start using the registered Anti-
Theft System key, it may be due to interference caused
by:
. Another Anti-Theft System key.
. Automated toll road device.
. Automated payment device.
. Other devices that transmit similar signals.
Start the engine using the following procedure:
1. Remove any items that may be causing the interference away from the Anti-Theft System key.
2. Leave the ignition switch in the “ON” position for approximately 5 seconds.
\f. Turn the ignition switch to the “OFF” or “LOCK” position, and wait approximately 10 seconds. 4. Repeat steps 2 and \f again.
5. Start the engine.
6. Repeat the steps above until all possible inter-
ferences are eliminated.
If this procedure allows the engine to start, RENAULT
recommends placing the registered Anti-Theft System
key separate from other devices to avoid interference.
FCC WARNING:
Changes or modifications not expressly ap-
proved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions; (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interference
that may cause undesired operation of the
device.
Security indicator light
SIC2045
The security indicator light is located on the meter
panel. It indicates the status of Anti-Theft System.
The light operates whenever the ignition switch is in the “LOCK”, “OFF” or “ACC” position. The security
indicator light indicates that the security systems on
the vehicle are operational.
If Anti-Theft System is malfunctioning, this light will
remain on while the ignition switch is in the “ON”
position.
If the light remains on and/or the engine does
not start, contact a RENAULT dealer for Anti-
Theft System service as soon as possible. Be
sure to bring all Anti-Theft System keys that you
have when visiting a RENAULT dealer for service.
For Right-Hand Drive (RHD) model (for Europe):
If Anti-Theft System is malfunctioning, the security
indicator light will illuminate when the ignition switch is
in the “ON” position. \bowever, if the security indicator
light turns off after 15 minutes, you can start the engine
once. See a RENAULT dealer for Anti-Theft System
service as soon as possible.
Pre-driving checks and adjustments\f-17
& R Q G L W L R Q
Page 139 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
not taken out from the loading slot, the CD \fill
automatically be reloaded to the slot to \brotect the CD
(12 cm discs only) .
AUX button:
The AUX IN jack is located on the audio unit. The AUX
IN audio in\but jack acce\bts any standard analog audio
in\but such as from a \bortable cassette ta\be, CD \blayer,
MP3 \blayer or la\bto\b com\buters.
Push the AUX button to \blay a com\batible device \fhen
it is \blugged into the AUX IN jack.
CAUTION:
. Do not allow the cable or an external device
connected to the AUX terminal to affect your
driving.
. Connect a stereo mini-plug (3.5 mm in
diameter) cable to the AUX IN jack. If a
monaural mini-plug cable is used, the audio
will not output correctly.
WARNING:
.Depending on the external device, please
note that the volume may be louder or
quieter than that of the external device.
. When the AUX contacts with the plug of the
connector cable, noise may be heard.
. The connected exterior device cannot be
operated with the main audio system. The
volume and sound quality can be adjusted.
. The song title in the external device cannot
be displayed on the audio display. .
For the power source of the external device,
use the special battery. The external device
cannot be charged with the AUX terminal.
Noise may be heard if the CD, radio etc. is
operated while charging the battery with the
power socket of the vehicle.
FM-AM radio o\beration
SAA3123
The audio system o\berates \fhen the ignition s\fitch is
in the “ACC” or “ON” \bosition.
/button:
When the
/button is \bushed \fhile the audio
system is off, the audio system \fill turn on and the
radio \fill turn on.
When the
/button is \bushed \fhile another
audio source is \blaying, the another audio source \fill
turn off and the radio \fill turn on.
To change the radio bands, \bush the
/button
until the desired band (FM1, FM2, AM) is dis\blayed.
The FM stereo indicator, “ST” \fill dis\blay during FM
stereo rece\btion. When the stereo broadcast signal is
\feak, the radio \fill automatically change from stereo
to monaural rece\btion.
TUNE/FF·REW/FOLDER button:
When adjusting the broadcasting station frequency
manually, \bush the
orbutton until the desired
frequency is achieved.
When adjusting the broadcasting station frequency
automatically, \bush the
orbutton. When the
system detects a broadcasting station, it \fill sto\b at
the station.
SEEK UP/DOWN button:
When adjusting the broadcasting station frequency
automatically, \bush the
button. When the
system detects a broadcasting station, it \fill sto\b at
the station.
button:
When the
button is \bushed, the system \fill seek
and sto\b at the detected broadcasting station for 5
seconds, and then it \fill start to seek for the next
broadcasting station.
Push the
button in this 5-second \beriod to sto\b
seeking.
Radio memory button:
The audio system can store u\b to 12 FM station
frequencies (for FM1 and FM2) and 6 AM station
frequencies.
To store the station frequency:
1. Tune to the desired broadcasting station fre- quency by using the
orbutton.
2. Push and hold a memory button (1 - 6) until a bee\b sounds.
Heater and air conditioner, and audio system4-19
& R Q G L W L R Q
Page 143 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
WARNING:
.Depending on the external device, please
note that the volume may be louder or
quieter than that of the external device.
. When the AUX contacts with the plug of the
connector cable, noise may be heard.
. The connected exterior device cannot be
operated with the main audio system. The
volume and sound quality can be adjusted.
. The song title in the external device cannot
be displayed on the audio display.
. For the power source of the external device,
use the special battery. The external device
cannot be charged with the AUX terminal.
Noise may be heard if the CD, radio etc. is
operated while charging the battery with the
power socket of the vehicle.
FM-AM radio operation
JVH0002X
\fhe audio s\bstem operates when the ignition switch is
in the “ACC” or “ON” position.
/button:
When the
/button is pushed while the audio
s\bstem is off, the audio s\bstem will turn on and the
radio will turn on.
When the
/button is pushed while another
audio source is pla\bing, the another audio source will
turn off and the radio will turn on.
\fo change the radio bands, push the
/button
until the desired band (FM1, FM2, or AM) is displa\bed.
\fhe FM stereo indicator, “S\f” will displa\b during FM
stereo reception. When the stereo broadcast signal is
weak, the radio will automaticall\b change from stereo
to monaural reception.
TUNE/FF·REW/FOLDER button:
When adjusting the broadcasting station frequenc\b
manuall\b, push the
orbutton until the desired
frequenc\b is achieved.
When adjusting the broadcasting station frequenc\b
automaticall\b, push the
orbutton. When the
s\bstem detects a broadcasting station, it will stop at
the station.
SEEK UP/DOWN button:
When adjusting the broadcasting station frequenc\b
automaticall\b, push the
button. When the
s\bstem detects a broadcasting station, it will stop at
the station.
button:
When the
button is pushed, the s\bstem will seek
and stop at the detected broadcasting station for 5
seconds, and then it will start to seek for the next
broadcasting station.
Push the
button in this 5-second period to stop
seeking.
Radio memory button:
\fhe audio s\bstem can store up to 12 FM station
frequencies (for FM1 and FM2) and 6 AM station
frequencies.
\fo store the station frequenc\b:
1. \fune to the desired broadcasting station fre- quenc\b b\b using the
orbutton.
2. Push and hold a memor\b button (1 - 6) until a beep sounds.
3. \fhe switch number and frequenc\b will appear on the displa\b when the memor\b is stored properl\b.
4. Perform steps 1 - 3 for all other memor\b buttons.
Push a memor\b button (1 - 6) to select a desired
memor\b.
If the batter\b cable is disconnected, or if the audio fuse
blows, the radio memor\b will be erased. In such a case,
reset the desired stations.
(Automatic Preset) button:
\fhe audio s\bstem can store up to 6 FM station
frequencies and 6 AM station frequencies.
\fo store the station frequenc\b automaticall\b, push and
hold the
button until a beep sounds. \fhe station
will be automaticall\b stored in the “AU\fO.P” memor\b.
\fhe displa\b indicates “AP-**”.
Heater and air conditioner, and audio system4-23
& R Q G L W L R Q
Page 145 of 352
![RENAULT PULSE 2012 1.G User Guide
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
16. Radio memory buttons
17. RP\f (Repeat)\bMIX (Mix play) button
Anti-theft system (if equipped)
\](/img/7/1587/w960_1587-144.png "RENAULT PULSE 2012 1.G User Guide
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
16. Radio memory buttons
17. RP\f (Repeat)\bMIX (Mix play) button
Anti-theft system (if equipped)
\")
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
16. Radio memory buttons
17. RP\f (Repeat)\bMIX (Mix play) button
Anti-theft system (if equipped)
\fhis unit can only be activated when the ignition switch
for Anti-\fheft System is in the “ACC” or “ON” position.
Each radio is uniquely matched to the vehicle’s
immobilizer and therefore cannot be transferred to
any other vehicle.
Audio main operation
\fhe audio system operates when the ignition switch is
in the “ACC” or “ON” position.
POWER ON/OFF button:
\fo turn on the audio system, push the POWER ON\b
OFF button.
.\fhe system will turn on in the mode, (radio or CD)
which was used immediately before the system
was turned off.
. If there is no CD loaded, the radio will be turned
on.
\fo turn off the audio system, push the POWER ON\b
OFF button.
Volume control:
\fo control the volume, turn the VOLUME control dial.
\furn the VOLUME control dial clockwise to make the
sound louder.
\furn the VOLUME control dial counterclockwise to
make the sound quieter.
Sound preference button:
\fo enter the audio mode (radio or CD) , push the
button. When no CD is loaded, the audio system will
automatically switch to the radio mode. \fo change the audio settings (BASS, \fREBLE,
FADER, BALANCE, EQ) , push the
button or
EN\fER button to select the mode.
BASS ?\fREBLE ?BALANCE ?FADER ?EQ ?
BASS
\fo adjust each audio setting, turn the VOL control dial
clockwise or counterclockwise.
BASS: ( í) to decrease \b (+) to increase
\fREB(LE): ( í) to decrease \b (+) to increase
BAL(ANCE): (R) to right balance \b (L) to left balance
FADE(R): (F) to front fade \b (R) to rear fade
EQ (Equalizer): Use this control to change the preset
sound mode for CD play.
\furn the MENU\bVOL dial clockwise or counterclock-
wise. \fhe mode will change as follows:
OFF ⇔ENHANCE
If the audio settings mode is unchanged for approxi-
mately 8 seconds, the audio settings mode will
automatically return to the normal mode.
MENU button:
\fo configure the SPEED volume and BEEP settings,
perform the following procedure:
1. Push the MENU button.
2. \furn the VOLUME dial clockwise or counter- clockwise. \fhe display message will change as
follows:
PHONE SE\fUP ⇔SPEED VOL⇔CLOCK ⇔
BEEP ⇔PHONE SE\fUP
. When SPEED VOL appears on the display, briefly
push on the EN\fER button then turn the VOLUME
dial clockwise or counterclockwise to adjust the
level of the volume. Adjusting the setting to 0 (zero) turns off the
speed volume feature. Increasing the speed
volume setting results in the audio volume
increasing more rapidly with vehicle speed. Push
the EN\fER button again to save the setting.
. When BEEP appears on the display, briefly push
the EN\fER button and then turn the VOLUME dial
clockwise or counterclockwise to switch the beep
sound on or off. Push the EN\fER button again to
save the setting.
\fo configure Alternative Frequency, Regional and
Language settings, perform the following procedure:
1. Push and hold the MENU button for at least 1.5 seconds.
2. \furn the VOLUME dial clockwise or counter- clockwise. \fhe display message will change as
follows:
AF⇔REG ⇔LANGUAGE ⇔AF
. \fo activate or deactivate the AF and REG mode,
briefly push on the EN\fER button when AF or
REG appears on the display and turn the
VOLUME dial clockwise or counterclockwise to
switch between the off or on position. After
selection, push the EN\fER button to confirm the
settings.
— When the AF mode is enabled, the audio unit
will automatically re-tune to a stronger fre-
quency if the radio signal becomes weak.
— When the REG mode is enabled, the audio unit will maintain and hold the station which is
broadcasting local (regional) programmes.
. \fo change the display language, briefly push the
EN\fER button when LANGUAGE appears on the
display then turn the VOLUME dial clockwise or
counterclockwise to select the appropriate lan-
guage setting.
Heater and air conditioner, and audio system4-25
& R Q G L W L R Q
Page 148 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
4-28Heater and air conditioner, and audio system
*1*2*3*4*5*6Radio memory buttons:
The audio system can store u\f to 18 FM station
\brequencies (six in each o\b FM 1, FM 2 and FM T) , 6
MW and 6 LW station \brequencies.
To store the station \brequency manually:
1. Tune to the desired broadcasting station \bre- quency by using the
orbutton.
2. Push and hold a radio memory button
*1-*6until a bee\f sounds. (The radio mutes when the
memory button is \fushed.)
3. The channel indicator will dis\flay and the radio mute disengages, indicating that the memory is
stored \fro\ferly.
4. Per\borm ste\fs 1 - 3 \bor all other memory buttons.
I\b the battery cable is disconnected, or i\b the audio \buse
blows, the radio memory will be erased. In such a case,
reset the desired stations.
Radio data system (RDS)
Alternative Frequency (AF):
. The AF \bunction o\ferates in the FM (radio) and CD
modes.
. When the AF mode is set to “ON” in the user
setu\f menu mode, the AF indicator illuminates.
For activation or deactivation details, see “Audio main
o\feration” (P.4-25) .
. Automatic switching function
This \bunction com\fares the strengths o\b the
signals o\b all the stations on the AF list and
selects the station with the o\ftimum rece\ftion
conditions.
. Program Information (PI) search
Program In\bormation (PI) search begins automati- cally i\b no suitable station is \bound with the above
automatic switching \bunction. The PI search
\bunction checks each RDS station with the same
PI code. During this time the sound is muted and
“PI SEARCH” is dis\flayed. The PI search o\fera-
tion sto\fs when a suitable station is \bound. I\b no
station is \bound once all the \brequencies have been
searched, the radio returns to the \frevious
\brequency.
. Enhanced Other Network (EON) data update
(This function also operates when the AF
mode is off.)
When EON data is being received, this enables
automatic retuning o\b other \freset stations on the
same network. Also, network linked services can
be used. The EON indicator turns on during the
rece\ftion o\b RDS EON stations in the FM mode.
RDS functions:
. Programme Service (PS) function (station
name display function)
When an RDS station is tuned in with seek or
manual tuning, the RDS data is received and the
Program Service (PS) name is dis\flayed.
. Emergency broadcast interrupt function
(ALARM INTERRUPTION —EBU SPEC FOR
INFO)
When the radio receives PTY code 31 (an
emergency broadcast code) , the sound is inter-
ru\fted, the emergency broadcast is heard, and
“PTY31 ALARM” is dis\flayed. The volume level at
this time is the same as that \bor tra\b\bic announce-
ments. Once the emergency broadcast is \binished,
the unit immediately returns to the \frevious
source.
. REG (Regional) mode
Some local radio stations are linked together according to their region because they only o\b\ber
limited coverage due to their limited number o\b
transmitters. I\b the signal \brom one station be-
comes weak while you are driving around, RDS
mode will switch to another local station in the
region with a stronger signal.
When the REG mode is activated in the FM band
and the radio receiver is tuned to a local radio
station, it will kee\f receiving this radio station
without switching to another local station. For
activation or deactivation details, see “Audio main
o\feration” (P.4-25) .
Traffic Announcement (TA):
. The TA \bunction o\ferates in the FM and CD
modes.
. The TA mode is turned on or o\b\b when the TA/
NEWS button is \fushed \bor less than 2 seconds.
. The TA mode o\ferates regardless o\b whether the
AF mode is on or o\b\b.
. “TA ON” is dis\flayed when the TA mode is turned
on, and the TA indicator turns on. “TA OFF” is
dis\flayed when the TA mode is turned o\b\b, and the
TA indicator turns o\b\b.
The \bollowing \bunctions o\ferate when the TA mode is
on:
. Traffic announcement interrupt function
When a tra\b\bic announcement is received, the
announcement is tuned in and the volume
increases to the set level.
Once the tra\b\bic announcement is \binished, the unit
returns to the source which was set be\bore the
tra\b\bic announcement started, and the volume
returns to the \frevious level. For EON stations,
the radio is interru\fted by another EON station
with tra\b\bic announcements.
The tra\b\bic announcement interru\ft mode is
& R Q G L W L R Q
Page 159 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
according to their region because they only offer
limited coverage due to their limited number of
transmitters\f If the signal from one station be-
comes wea\b while you are driving around, RDS
mode will switch to another local station in the
region with a stronger signal\f
When the REG mode is activated in the FM band
and the radio receiver is tuned to a local radio
station, it will \beep receiving this radio station
without switching to another local station\f For
activation or deactivation, use the MENU button\f
(Details are explained later in this section\f)
Traffic Announcement (TA):
. The TA function operates in the FM and CD
modes\f
. The TA mode is turned on or off when the TA
button is pushed for less than 2 seconds\f
. The TA mode operates regardless of whether the
AF mode is on or off\f
. “TA ON” is displayed when the TA mode is turned
on, and the TA indicator turns on\f “TA OFF” is
displayed when the TA mode is turned off, and the
TA indicator turns off\f
The following functions operate when the TA mode is
on:
. Traffic announcement interrupt function
When a traffic announcement is received, the
announcement is tuned in and the volume
increases to the set level\f
Once the traffic announcement is finished, the unit
returns to the source which was set before the
traffic announcement started, and the volume
returns to the previous level\f For EON stations,
the radio is interrupted by another EON station
with traffic announcements\f
The traffic announcement interrupt mode is cancelled if the TA button is pushed during a
traffic announcement\f The TA mode returns to the
standby mode and the audio unit returns to the
previous source\f
News mode
When the NEWS button is pushed for longer than 2
seconds in the FM mode, the news function is
activated\f “NEWS” is displayed for 3 seconds and
the NEWS indicator appears on the display\f
When the news function is activated, the radio
receives a news code from the FM broadcasting news
station and the actual playing mode will be interrupted\f
Once the news broadcast is finished, the unit returns
to the previous mode\f
In some countries or regions, this service is not
available or the signal is too wea\b to be received\f
1\f News standby mode
.The news standby mode can be activated in
the FM or CD mode\f
.A news interruption will be announced and
“NEWS” will be displayed when the radio
detects the news code from the tuned station
or EON stations\f The display will then change
to the PS name of the interrupting station\f
.When pushing the NEWS button for longerthan 2 seconds, the news standby mode is
turned off and the indicator disappears from
the display\f
2\f News interruption mode
.When the NEWS button is pushed during the
news interruption mode, the radio returns to the
previous source\f However, the news standby
mode is maintained\f
.When thebutton is pushed during the
news interruption mode, the radio changes to the CD mode\f However, the news standby
mode is maintained\f
If the radio band is changed to the MW or LW,
the news standby mode will be turned off\f
MENU button:
To configure Alternative Frequency, Regional and
Language settings, perform the following procedure:
1\f Push and hold the MENU button for at least 1\f5 seconds\f
2\f Turn the VOLUME control dial cloc\bwise or countercloc\bwise\f The display message will
change as follows:
AF⇔REG ⇔LANGUAGE ⇔AF
. To activate or deactivate the AF and REG mode,
briefly push the ENTER button when AF or REG
appears on the display and turn the VOLUME
control dial cloc\bwise or countercloc\bwise to
switch between the off or on position\f After
selection, push the ENTER button to confirm the
settings\f
— When the AF mode is enabled, the audio unit
will automatically re-tune to a stronger fre-
quency if the radio signal becomes wea\b\f
— When the REG mode is enabled, the audio unit will maintain and maintain the station which is
broadcasting local (regional) programmes\f
. To change the display language, briefly push the
ENTER button when LANGUAGE appears on the
display then turn the MENU/VOL dial cloc\bwise or
countercloc\bwise to select the appropriate lan-
guage setting\f
ENGLISH ⇔DUTCH ⇔FRENCH ⇔SPANISH
⇔ GERMAN ⇔ITALIAN ⇔PORTUGUESE ⇔
ENGLISH
Heater and air conditioner, and audio system4-39
& R Q G L W L R Q