maintenance RENAULT PULSE 2012 1.G Owner's Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2012, Model line: PULSE, Model: RENAULT PULSE 2012 1.GPages: 352, PDF Size: 6.46 MB
Page 259 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
SDI2578HR12DE engine modelJVM0001XHR15DE engine model1. Oil fille\f cap
2. Oil \b\fain plug
3. Oil filte\f
1. Pa\fk the vehicle on a level su\fface an\b apply the pa\fking b\fake.
2. Tu\fn the engine off.
3. D\fain the engine oil acco\f\bing to the p\fope\f p\foce\bu\fe. (See “Engine oil \feplacement
(HR12DDR, HR12DE an\b HR15DE engine mo\b-
els)” (P.8-11) .) 4. Loosen the oil filte\f with an oil filte\f w\fench.
Depen\bing on the engine mo\bel, a special cap
type w\fench may be \fequi\fe\b. See a RENAULT
\beale\f fo\f mo\fe info\fmation.
5. Remove the oil filte\f by tu\fning it by han\b.
6. Wipe the engine oil filte\f mounting su\fface with a clean cloth.
Be su\fe to \femove any ol\b gasket \femaining on the
mounting su\fface.
7. Apply the new engine oil to the gasket of the new oil filte\f.
8. Sc\few in the oil filte\f until a slight \fesistance is felt, an\b then tighten an a\b\bitional 2/3 of tu\fn to
secu\fe the oil filte\f.
Oil filter tightening torque:15 to 20 N·m (11 to 14 ft-lb)
9. Refill the engine oil. (See “Engine oil \feplacement (HR12DDR, HR12DE an\b HR15DE engine mo\b-
els)” (P.8-11) .)
10. Sta\ft the engine an\b check fo\f leakage a\foun\b the oil filte\f. Co\f\fect as \fequi\fe\b.
11. Tu\fn the engine off an\b wait seve\fal minutes.
12. Check the engine oil level acco\f\bing to the p\fope\f p\foce\bu\fe. (See “Checking engine oil level” (P.8-
10) .)
Maintenance and do-it-yourself8-13
& R Q G L W L R Q
Page 260 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
8-14Maintenance and do-it-yourself
Engine oil and filter replacement \fK9K engine
model)
\bDI2472
1. Oil drain plug
2. Oil filter
1. Place a large drain pan under the drain plug.
2. Remove the drain plug with a wrench.
3. Remove the oil filler cap and completely drain the oil.
If the oil filter is to be changed, remove and
replace it at this time.
CAUTION:
Waste oil must be disposed of properly. Check
your local regulations.
4. Loosen the oil filter with an oil filter wrench.
5. Remove the oil filter by turning it by hand.
6. Wipe the entire oil filter mounting surface with aclean cloth.
Be sure to remove any old gasket remaining on the
mounting surface. 7. Apply new engine oil to the gasket on the new oil
filter.
8. \bcrew in the oil filter until a slight resistance is felt, and then tighten an additional 3/4 of a turn to
secure the filter.
Oil filter tightening torque:16 to 20 N·m (1.6 to 2.0 kg-m, 12 to 15 ft-lb)
9. Clean and reinstall the drain plug and new washer. \becurely tighten the drain plug with a wrench. Do
not use excessive force.
Drain plug tightening torque:16 to 24 N·m (1.6 to 2.4 kg-m, 12 to 18 ft-lb)
10. Refill the recommended engine oil and quantity. \f\bee “Recommended fuel/lubricants and capaci-
ties” \fP.9-2) .)
11. \becurely install the oil filler cap.
12. \btart the engine.
13. Check the drain plug and the oil filter for any sign of leakage.
14. Dispose of the used oil in the proper manner. Check your local regulations.
15. Check the engine oil level according to the proper procedure. \f\bee “Checking engine oil level” \fP.8-
10) .)
After operation
1. Install the engine undercover \fif removed) intoposition as the following steps.
a. Pull the center of each plastic clip out.
b. Hold the engine undercover into position.
c. Insert the clips through the undercover into thehole in the frame, then push the center of the
clips in to lock the clips in place. d. \bcrew in the bolts, then tighten them.
2. Lower the vehicle carefully to the ground.
PROTECT ENVIRONMENT
It is illegal to pollute drains, watercourses and soil. Use
authorized waste collection facilities, including civil
amenity sites and garages providing facilities for
disposal of used oil and used oil filters. If in doubt,
contact your local authority for advice on disposal.
The regulations concerning the pollution of the
environment will vary from country to country.
& R Q G L W L R Q
Page 261 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
DRAINING WATER
Drain water in the fue\f fi\fter accordin\b to the
maintenance \fo\b shown in a separate maintenance
book\fet.
If the water-in-fue\f-fi\fter\u warnin\b \fi\bht
i\f\fuminates
whi\fe the en\bine is runnin\b, there mi\bht be water in the
fue\f fi\fter.
The fue\f fi\fter can be accessed after removin\b the fuse
box and the battery from the vehic\fe. Therefore,
RENAULT recommends that you contact a RENAULT
dea\fer for servicin\b.
BLEEDING FUEL SYSTEM
SDI2714
B\feed air out of the fue\f system after refi\f\fin\b an empty
fue\f tank by the fo\f\fowin\b action:
1. Squeeze the primin\b pump
*1\focated in the
en\bine compartment severa\f times unti\f there is a
sudden resistance fe\ft in the pressure, then stop.
2. Crank the en\bine unti\f it starts. Do not crank the en\bine for more than 30 seconds.
3. If the en\bine does not start, stop crankin\b and repeat step 1 above. 4. If the en\bine does not operate smooth\fy after it has
started, race it two or three times.
JVM0061XHR12DDR engine1. Superchar\ber
2. Water pump
3. A\fternator
4. E\fectroma\bnetic c\futch
5. Crankshaft pu\f\fey
6. Drive be\ft auto-tensioner
7. Air conditioner compressor
Maintenance and do-it-yourself8-15
FUEL FILTER (diesel engine model)
DRIVE BELTS
& R Q G L W L R Q
Page 262 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
8-16Maintenance and do-it-yourself
SDI2573HR 12DE engine or HR 15DE engine1. Water pu\fp
2. Alternat\br
3. Crankshaft pulley
4. Air c\bnditi\bner c\b\fpress\br (with air c\b\fpres-s\br)
Idler pulley (with\but air c\b\fpress\br)
!: Tensi\bn checking p\bint
SDI2484K9K engine1. Crankshaft pulley
2. Drive belt aut\b-tensi\bner
3. Alternat\br
4. Air c\bnditi\bner c\b\fpress\br
Be sure the igniti\bn switch is in the “OFF” p\bsiti\bn. Visually inspect each belt f\br signs \bf unusual wear,
cuts, fraying \br l\b\bseness. Check regularly f\br c\bndi-
ti\bn and tensi\bn. If the belt is in p\b\br c\bnditi\bn \br l\b\bse,
have it replaced \br adjusted by a RENAULT dealer.
WARNING:
Be sure the engine and ignition switch are off
and that the parking brake is applied.
Replace the spark plugs acc\brding t\b the \faintenance
l\bg sh\bwn in a separate \faintenance b\b\bklet.
If replace\fent is required, c\bntact a RENAULT dealer.
SDI1895
IRIDIUM-TIPPED SPARK PLUGS (if
equipped)
It is n\bt necessary t\b replace the iridiu\f-tipped*Aspark plugs as frequently as the c\bnventi\bnal type \bf
spark plugs. These spark plugs are designed t\b last
\fuch l\bnger than the c\bnventi\bnal type \bf spark plug.
CAUTION:
.
Do not reuse the iridium-tipped spark plugs
by cleaning or re-gapping.
. Always replace with the recommended ir-
idium-tipped spark plugs.
SPARK PLUGS (gasoline engine
model)
& R Q G L W L R Q
Page 263 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
NICKEL-TIPPED SPARK PLUGS (if
e\fuipped\b
It is not necessary to replace the nickel-tipped*Aspark plugs as fre\fuently as the conventional type of
spark plugs. These spark plugs are designed to last
much longer than the conventional type of spark plug.
CAUTION:
.Do not reuse the nickel-tipped spark plugs
by cleaning or re-gapping.
. Always replace with the recommended nick-
el-tipped spark plugs.
CHECKING PARKING BRAKE
Lever type
SDI1447A
From the released position, pull the parking brake lever
up slowly and firmly. If the number of clicks is out of the
range listed, see a RENAULT dealer.
For Thailand, Indonesia, Singapore, China, Hong
Kong, Brunei and Pakistan:
9 to 10 clicksPulling force 196 N (20 kg, 44 lb)
For India: 8 to 9 clicks (for model with ABS or K9K
engine model)
9 to 10 clicks (for model without ABS)Pulling force 196 N (20 kg, 44 lb)
For Australia and New Zealand: 11 to 12 clicksPulling force 196 N (20 kg, 44 lb) Except for Thailand, Indonesia, Singapore, Chi-
na, Hong Kong, Brunei, India, Australia, New
Zealand and Pakistan:
8 to 9 clicksPulling force 196 N (20 kg, 44 lb)
CHECKING FOOT BRAKE PEDAL
DI1020MR
WARNING:
See a RENAULT dealer for a brake system check
if the foot brake pedal height does not return to
normal.
With the engine running, check the distance
*Abetween the upper surface of the pedal and the metal
floor. If it is out the range listed, see a RENAULT
dealer.
*A: Depressing force
490 N (50 kg, 110 lb)
— 80 mm (3.15 in) or more
Maintenance and do-it-yourself8-17
BRAKES
& R Q G L W L R Q
Page 264 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
8-18Maintenance and do-it-yourself
Self-adjusting brakes
\four vehi\ble is equipped with self-adjusting brakes.
The brakes are adjusted by the foot brake pedal
operation.
Brake pad wear indi\bator
The dis\b brake pads on your vehi\ble have audible wear
indi\bators. When a brake pad requires repla\bement, it
will make a high pit\bhed s\braping or s\bree\bhing sound
when the vehi\ble is in motion. The noise will be heard
whether or not the foot brake pedal is depressed. Have
the brakes \bhe\bked as soon as possible if the wear
indi\bator sound is heard.
Under some driving or \blimate \bonditions, o\b\basional
brake squeaks, squeals or other noises may be heard.
O\b\basional brake noise during light to moderate stops
is normal and does not affe\bt the fun\btion or
performan\be of the brake system.
The rear drum brakes do not have audible wear
indi\bators. Should you ever hear an unusually loud
noise from the rear drum brakes, have them \bhe\bked
as soon as possible by a RENAULT dealer.
Proper brake inspe\btion intervals should be followed.
For additional information, see a separate maintenan\be
booklet.
BRAKE BOOSTER
Che\bk the brake booster fun\btion as follows:
1. With the engine off, depress and release the footbrake pedal several times. When the foot brake
pedal movement (distan\be of travel) remains the
same from one pedal appli\bation to the next,
\bontinue on to the next step.
2. While depressing the foot brake pedal, start the engine. The pedal height should drop a little. 3. With the foot brake pedal depressed, stop the
engine. Keep the pedal depressed for about 30
se\bonds. The pedal height should not \bhange.
4. Run the engine for 1 minute without depressing the foot brake pedal, then turn it off. Depress the
foot brake pedal several times. The pedal travel
distan\be will de\brease gradually with ea\bh de-
pression as the va\buum is released from the
booster.
If the brakes do not operate properly, have the brakes
\bhe\bked by a RENAULT dealer.
WARNING:
. Use only new fluid from a sealed container.
Old, inferior, or contaminated fluid may
damage the brake system. The use of
improper fluids can damage the brake
system and affect the vehicle’ s stopping
ability.
. Clean the filler cap before removing.
. Brake fluid is poisonous and should be
stored carefully in marked containers out
of the reach of children.
CAUTION:
Do not spill the fluid on painted surfaces. This
will damage the paint. If fluid is spilled, wash it
off with plenty of water immediately.
SDI0890
Che\bk the fluid level in the reservoir. If the brake fluid is
below the MIN line, the brake warning light will
illuminate. Add brake fluid up to the MAX line. (See
“Re\bommended fuel/lubri\bants and \bapa\bities” (P.9-2)
for re\bommended types of brake fluid.)
If the brake fluid must be added frequently, the brake
BRAKE FLUID
& R Q G L W L R Q
Page 265 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
system should be thoroughly checked by a REN\fULT
dealer\bWARNING:
.Use only new fluid from a sealed container.
Old, inferior, or contaminated fluid may
damage the clutch system.
. Clean the filler cap before removing.
. Clutch fluid is poisonous and should be
stored carefully in marked containers out of
the reach of children.
CAUTION:
Do not spill the clutch fluid on painted surfaces.
This will damage the paint. If clutch fluid is
spilled, wash it off with plenty of water immedi-
ately.
SDI0890
Check the fluid level in the reservoir\b If the fluid is
below the MIN line, add fluid up to the M\fX line\b (See
“Recommended fuel/lubricants and capacities” (P\b9-2)
for the recommended types of fluid\b)
If the fluid must be added frequently, the clutch system
should be thoroughly checked by a REN\fULT dealer\b Contact a REN\fULT dealer if checking or replacement
is required\b
CAUTION:
.
Use only fluids approved by our technical
department. Do not mix with other fluids.
. Using automatic transmission fluid other
than fluids approved by our technical de-
partment will cause deterioration in drive-
ability and transmission durability, and may
damage the transmission, which is not
covered by the warranty.
Maintenance and do-it-yourself8-19
CLUTCH FLUID (if equipped)
AUTOMATIC TRANSMISSION FLUID
(ATF) (if equipped)
& R Q G L W L R Q
Page 266 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
8-20Maintenance and do-it-yourself
Contact a RENAULT dea\fer if c\becking or rep\facement
is required.
CAUTION:
.Use only fluids approved by our technical
department. Do not mix with other fluids.
. Using transmission fluid other than fluids
approved by our technical department will
damage the CVT, which is not covered by the
warranty. T\be viscous paper type fi\fter e\fement s\bou\fd not be
c\feaned and reused.
T\be dry paper type fi\fter e\fement may be c\feaned and
reused.
Rep\face t\be air c\feaner fi\fter according to t\be main-
tenance \fog s\bown in a separate maintenance book\fet.
Contact a RENAULT dea\fer if maintenance or rep\face-
ment is required.
WARNING:
Operating the engine with the air cleaner filter
off can cause you or others to be burned. The air
cleaner filter not only cleans the intake air, it
also stops flame if the engine backfires. If the air
cleaner filter is not installed and the engine
backfires, you could be burned. Never drive with
the air cleaner filter off. Be cautious working on
the engine when the air cleaner filter is off.
WINDSHIELD WIPER BLADES
C\feaning
If t\be winds\bie\fd does not become c\fear after using t\be
winds\bie\fd was\ber or if t\be wiper b\fades c\batter w\ben
operating t\be winds\bie\fd wipers, wax or ot\ber materia\fs
may be on t\be winds\bie\fd and/or wiper b\fades.
C\fean t\be outside of t\be winds\bie\fd surface wit\b a
was\ber so\fution or mi\fd detergent. Your winds\bie\fd is
c\fean if beads do not form w\ben rinsing wit\b water.
C\fean t\be b\fade by wiping it wit\b a c\fot\b soaked in a
was\ber so\fution or a mi\fd detergent. Rinse t\be b\fade
wit\b water. If your winds\bie\fd is sti\f\f not c\fear after
c\feaning t\be b\fades and using t\be wipers, rep\face t\be
b\fades.
CONTINUOUSLY VARIABLE
TRANSMISSION (CVT) FLUID (if
equipped)
AIR CLEANER FILTER
WIPER BLADES
& R Q G L W L R Q
Page 267 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
SDI1865
Be careful not to clog t\fe was\fer nozzle*A\b T\fis may
cause improper winds\field was\fer operation\b If t\fe
nozzle is clogged, remove any objects wit\f a needle or
small pin
*B\b Be careful not to damage t\fe nozzle\b
Replacing
SDI1803
1\b Lift t\fe wiper arm away from t\fe winds\field\b
2\b Pus\f and \fold t\fe release tab
*A, and t\fen move
t\fe wiper blade down t\fe wiper arm to remove
*1\b
3\b Remove t\fe wiper blade\b
4\b Insert t\fe new wiper blade onto t\fe wiper arm until it clicks into place\b
CAUTION:
.After wiper blade replacement, return the
wiper arm to its original position. Otherwise
the wiper arm or the engine hood may be
scratched and may cause damage.
. Worn windshield wiper blades can damage
the windshield and impair driver vision.
REAR WINDOW WIPER BLADE (if
equipped)
Contact a RENAULT dealer if c\fecking or replacement
is required\b
Maintenance and do-it-yourself8-21
& R Q G L W L R Q
Page 268 of 352
> ( G L W 0 R G H O . $ 2 ( 0 B 5 H Q D X O W @
8-22Maintenance and do-it-yourself
SDI2574Type A
JVM0023XType B
WARNING:
Anti-freeze is poisonous and should be stored
carefully in marked containers out of the reach
of children.
Type \f: Che\bk the fluid level in the window washer
reservoir. If the fluid level is low, add window washer
fluid up to the M\fX level.
Type B: To \bhe\bk the fluid level, use your finger to plug
the \benter hole
*1of the \bap/tube assembly, then
remove it from the reservoir. If there is no fluid in the
tube, add fluid. \fdd a washer solvent to the water for better \bleaning.
In the winter season, add a windshield washer anti-
freeze. Follow the manufa\bturer’s instru\btions for the
mixture ratio.
WINDOW WASHER FLUID
& R Q G L W L R Q