wheel RENAULT PULSE 2012 1.G Owner's Guide


> (GLW    0RGHO .$2(0 B5HQDXOW @
The Stop/Start System is designed to prevent
unne\fessary fuel \fonsumption, e\bhaust emissions,
and noise during a journey:
.When the vehi\fle \fomes to rest the engine is
automati\fally stopped.
. The engine is then automati\fally restarted before
you are ready to drive away.
CAUTION:
At the end of the journey the engine must be
stopped and ignition switch be turned off. Lock
the vehicle as normal. Turning the ignition OFF
will shut down all electrical systems. Failure to
do this may result in a flat battery.
NORMAL OPERATION
The Stop/Start System stops the engine and will
automati\fally restart the engine. The Stop/Start
indi\fator light is shown in the meter.
The Stop/Start System will automati\fally stop
the engine when all the following \fonditions
are valid.
For MT model
.The shift lever is in Neutral position.
. The \flut\fh pedal is fully released.
. The vehi\fle speed is below about 2 km/h (1
MPH) .
. The driver’s seat belt is fastened.
. The Intelligent Key is in the vehi\fle.
. The driver’s door is \flosed.
For CVT model
. The sele\ftor lever is in the "D" (Drive) or "N"
(Neutral) position. .
The brake pedal is depressed.
. The vehi\fle is stopped.
. The driver’s seat belt is fastened.
. The driver’s door is \flosed.
NOTE:
The following conditions must also be satisfied
before the engine is automatically stopped. If
the engine does not stop this does not indicate a
malfunction in the system:
. The engine coolant temperature is at normal
operating levels.
. The vehicle has driven some distance since
engine start.
. The battery voltage and temperature are
within normal levels.
. The hood is closed.
. The steering wheel is not being turned.
. The system is not in front defogger mode.
(automatic air conditioner)
. The mode dial is not in front defogger mode.
(manual air conditioner)
. The rear window defogger is not operated.
NOTE:
The engine will not restart if the brake pedal is
released while the Stop/Start System is acti-
vated under the following condition:
. The selector lever is in the "P" (Park) position
(for CVT model) .
When the Stop/Start System indi\fator light is
displayed the engine starts running automa-
ti\fally under at least one of the following
\fonditions.
.The \flut\fh pedal is depressed (for MT model) .
. The brake pedal is released with the sele\ftor lever
in the "D"(Drive) or "N"(Neutral) position (for CVT
model) .
. The sele\ftor lever is pla\fed in the "L"(Low) ,
"D"(Drive) or "R"(Reverse) position from the "N"
or "P" position (for CVT model) .
. The driver’s seat belt is unfastened, or the driver’s
door is open (for CVT model) .
. The brake pedal is repeatedly pressed (to maintain
vehi\fle braking performan\fe) .
. The brake pedal is strongly depressed and then
released with the sele\ftor lever in the "P" (Park)
position, resulting in de\freased va\fuum pressure
of the brake booster (for CVT model) .
. The battery voltage be\fomes low (due to ele\ftri\fal
load from other vehi\fle systems like headlights,
heaters, et\f., or au\biliary devi\fes \fonne\fted to the
12 volt so\fket inside the vehi\fle) .
. The vehi\fle speed is above about 2 km/h (1
MPH) .
. The system is in front defogger mode. (automati\f
air \fonditioner)
. The mode dial is in front defogger mode. (manual
air \fonditioner)
. The rear window defogger is operated.
NOTE:
The following conditions will prevent the Stop/
Start System from automatically restarting the
engine. Starting the engine by the ignition
switch is then necessary:
Starting and driving5-21
STOP/START SYSTEM (if equipped
for Europe)
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
5-24Starting and driving
WARNING:
.The VDC system is designed to help improve
driving stability but does not prevent acci-
dents due to abrupt steering operation at
high speeds or due to careless or dangerous
driving techniques. Reduce vehicle speed
and be especially careful when driving and
cornering on slippery surfaces and always
drive carefully.
. Do not modify the vehicle’s suspension. If
suspension parts such as shock absorbers,
struts, springs, stabilizer bars, bushings and
wheels are not RENAULT-approved or are
extremely deteriorated, the VDC system may
not operate properly. This could adversely
affect vehicle handling performance, and the
“VDC OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate.
. If brake related parts such as brake pads,
rotors and calipers are not standard equip-
ment or are extremely deteriorated, the
“VDC OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate.
. If engine related parts such as a muffler are
not standard equipment or are extremely
deteriorated, the “VDC OFF” indicator or
“ SLIP ”indicator or both indicator lights
may illuminate.
. When driving on extremely inclined surfaces
such as higher banked corners, the VDC
system may not operate properly and the
“VDC OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate. Do not
drive on these types of roads. .
When driving on unstable surfaces such as a
turntable, ferry, elevator or ramp, the “VDC
OFF” indicator or “SLIP”indicator or both
indicator lights may illuminate. This is not a
malfunction. Restart the engine after driving
onto a stable surface.
. If wheels or tires other than those recom-
mended are used, the VDC system may not
operate properly and “VDC OFF”indicator or
“SLIP” indicator or both indicator lights may
illuminate.
. The VDC system is not a substitute for winter
tires or tire chains on a snowcovered road.
When accelerating or \friving on slipper\b surfaces, the
tires ma\b spin or sli\fe. With the Vehicle D\bnamic
Control (VDC) s\bstem, sensors \fetect these move-
ments an\f control the braking an\f engine output to
help improve vehicle stabilit\b.
. When the VDC s\bstem is operating, the “SLIP”
in\ficator in the instrument panel blinks.
. If the “SLIP” in\ficator blinks, the roa\f con\fitions
are slipper\b. Be sure to a\fjust \bour spee\f an\f
\friving to these con\fitions. Be sure to \frive
carefull\b. (See “Slip in\ficator light” (P.2-17)
an\f“Vehicle D\bnamic Control (VDC) off in\ficator
light” (P.2-18) .)
. In\ficator light
If a malfunction occurs in the s\bstem, the “SLIP”
an\f “VDC OFF” in\ficator lights illuminate in the
instrument panel. As long as these in\ficators are
illuminate\f, the VDC s\bstem function is cancele\f.
The VDC s\bstem uses a Brake Limite\f Slip Differential
(BLSD) function to improve vehicle traction. The BLSD
s\bstem works when one of the \friving wheels is
spinning on a slipper\b surface. The BLSD s\bstem
brakes the spinning wheel, which \fistributes the \friving power to the other \frive wheel. If the vehicle
is operate\f with the VDC OFF switch pushe\f an\f the
VDC s\bstem turne\f off, all VDC s\bstems will be turne\f
off. The BLSD s\bstem will still operate with the VDC
s\bstem off. If the BLSD s\bstem is activate\f, the “SLIP”
in\ficator light will blink an\f \bou ma\b hear a clunk noise
an\f/or feel a pulsation in the foot brake pe\fal. This is
normal an\f is not an in\fication of a malfunction. While
the VDC s\bstem is operating, \bou ma\b feel a pulsation
in the foot brake pe\fal an\f hear a noise or feel a
vibration from un\fer the hoo\f. This is normal an\f
in\ficates that the VDC s\bstem is working properl\b.
The VDC s\bstem computer has a built-in \fiagnostic
feature that tests the s\bstem each time \bou start the
engine an\f move the vehicle at a low spee\f forwar\f or
backwar\f. When the self-test occurs, \bou ma\b hear a
“clunk” noise an\f/or feel a pulsation in the foot brake
pe\fal. This is normal an\f is not an in\fication of a
malfunction.
VEHICLE DYNAMIC CONTROL (VDC) OFF
SWITCH
SIC1881
The vehicle shoul\f be \friven with the Vehicle D\bnamic
Control (VDC) s\bstem ON for most \friving con\fitions.
When the vehicle is stuck in mu\f or snow, the VDC
VEHICLE DYNAMIC CONTROL (VDC)
SYSTEM (if equipped except for
Europe)
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
system reduces the engine output to reduce wheel
spin. The engine speed will \fe reduced even if the
accelerator is depressed to the floor. \bf maximum
engine power is needed to free a stuck vehicle, turn
the VDC system off.
To turn off the Vehicle Dynamic Control (VDC) system,
push the VDC OFF switch. The
indicator light will
illuminate on.
Push the VDC OFF switch again or restart the engine
to turn ON the system.
WARNING:
. The Electronic Stability Program (ESP) sys-
tem is designed to help improve driving
stability but does not prevent accidents due
to abrupt steering operation at high speeds
or due to careless or dangerous driving
techniques. Reduce vehicle speed and be
especially careful when driving and corner-
ing on slippery surfaces and always drive
carefully.
. If engine related parts such as a muffler are
not standard equipment or the “ESP OFF”
indicator or “SLIP”indicator or both indica-
tor lights may illuminate.
. Do not modify the vehicle’s suspension. If
suspension parts such as shock absorbers,
struts, springs, stabilizer bars and bushings
are not RENAULT approved or are extremely
deteriorated the ESP system may not oper-
ate properly. This could adversely affect
vehicle handling performance, and the
“ESP OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate.
. If brake related parts such as brake pads,
rotors and calipers are not standard equip-
ment or are extremely deteriorated, the “ESP
OFF” indicator or “SLIP”indicator or both
indicator lights may illuminate.
. When driving on extremely inclined surfaces
such as higher banked corners, the ESP
system may not operate properly and the
“ESP OFF” indicator or “SLIP”indicator or
both indicator lights may illuminate. Do not
drive on these types of roads. .
When driving on unstable surfaces such as a
turntable, ferry, elevator or ramp, the “ESP
OFF” indicator or “SLIP”indicator or both
indicator lights may illuminate. This is not a
malfunction. Restart the engine after driving
onto a stable surface.
. If wheels or tires other than those recom-
mended are used, the ESP system may not
operate properly and “SLIP”indicator light
may illuminate.
. The ESP system is not a substitute for winter
tires or tire chains on a snow-covered road.
. When the ESP system is operating, the “SL\bP”
indicator
in the instrument panel \flinks.
. \bf the “SL\bP” indicator \flinks, the road conditions
are slippery. Be sure to adjust your speed and
driving to these conditions. Be sure to drive
carefully. (See “Slip indicator light” (P.2-17) and
“Electronic Sta\fility Program (ESP) off indicator
light” (P.2-16) .)
. \bndicator light
\bf a malfunction occurs in the system, the “SL\bP”
indicator lights illuminate in the instrument
panel. As long as these indicators are illuminated,
the ESP system function is canceled.
The ESP system uses a Brake Limited Slip Differential
(BLSD) function to improve vehicle traction. The BLSD
system works when one of the driving wheels is
spinning on a slippery surface. The BLSD system
\frakes the spinning wheel, which distri\futes the
driving power to the other drive wheel. \bf the vehicle
is operated with the ESP system turned off, all ESP
system functions will \fe turned off.
The BLSD system and ABS will still operate with the
ESP system off. \bf the BLSD system is activated, the
“SL\bP” indicator light will \flink and you may hear a
Starting and driving5-25
ELECTRONIC STABILITY PROGRAM
(ESP) SYSTEM (if equipped for
Europe)
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
5-26Starting and driving
clunk noise and/or feel a pulsa\fion in \fhe brake pedal.
\bhis is normal and is no\f an indica\fion of a malfunc\fion.
While \fhe ESP sys\fem is opera\fing, you may feel a
pulsa\fion in \fhe brake pedal and hear a noise or feel a
vibra\fion from under \fhe hood. \bhis is normal and
indica\fes \fha\f \fhe ESP sys\fem is working properly.
\bhe ESP sys\fem compu\fer has a buil\f-in diagnos\fic
fea\fure \fha\f \fes\fs \fhe sys\fem each \fime you s\far\f \fhe
engine and move \fhe vehicle a\f a low speed forward or
backward. When \fhe self-\fes\f occurs, you may hear a
“clunk” noise and/or feel a pulsa\fion in \fhe foo\f brake
pedal. \bhis is normal and is no\f an indica\fion of a
malfunc\fion.
ELEC\bRONIC S\bABILI\bY PROGRAM (ESP)
OFF SWI\bCH
JVS0022X
\bhe vehicle should be driven wi\fh \fhe Elec\fronic
S\fabili\fy Program (ESP) sys\fem on for mos\f driving
condi\fions.
When \fhe vehicle is s\fuck in mud or snow, \fhe ESP
sys\fem reduces \fhe engine ou\fpu\f \fo reduce wheel
spin. \bhe engine speed will be reduced even if \fhe
accelera\for is depressed \fo \fhe floor. If maximum
engine power is needed \fo free a s\fuck vehicle, \furn
\fhe ESP sys\fem off.\bo \furn off \fhe ESP sys\fem, push \fhe ESP OFF swi\fch
loca\fed on \fhe lower side of \fhe ins\frumen\f panel.
\bhe
indica\for ligh\f will illumina\fe.
Push \fhe ESP OFF swi\fch again or res\far\f \fhe engine
\fo \furn on \fhe sys\fem. \bhe speed limi\fer allows you \fo se\f \fhe desired vehicle
speed limi\f. While \fhe speed limi\fer is ac\fiva\fed, \fhe
driver can perform normal braking and accelera\fion,
bu\f \fhe vehicle will no\f exceed \fhe se\f speed.
WARNING:
.
Always observe posted speed limits. Do not
set the speed over them.
. Always confirm the setting status of the
speed limiter on the vehicle information
display and instrument panel.
When \fhe speed limi\fer is on, \fhe cruise con\frol canno\f
be opera\fed.
SPEED LIMI\bER OPERA\bIONS
Excep\f for HR12DDR engine model: \bhe speed limi\fer
can be se\f be\fween 30 km/h and 170 km/h or 20 MPH
and 105 MPH.
For HR12DDR engine model (for M\b model): \bhe
speed limi\fer can be se\f be\fween 30 km/h and 180
km/h or 20 MPH and 112 MPH.
For HR12DDR engine model (for CV\b model): \bhe
speed limi\fer can be se\f be\fween 30 km/h and 170
km/h or 20 MPH and 105 MPH.
\bhe speed limi\fer se\f swi\fches are loca\fed on \fhe
s\feering wheel.
SPEED LIMITER (if equipped for
Europe)
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
quickly become high enough to cause se-
vere or possibly fatal illness to people and
animals.
SSD0488
Left-Hand Drive (LHD) model
SSD0489
Right-Hand Drive (RHD) model1. Firmly apply the par\fing bra\fe.
\b. Automatic Transmission (AT)/Continuously Vari-able Transmission (CVT) model: Move the selector
lever to the “P” (Par\f) position.
Manual Transmission (MT) model: Move the shift
lever to the “R” (Reverse) position. When par\fing
on an uphill grade, move the shift lever to the “1”
(1st) position. 3. To help prevent the vehicle from moving into traffic
when par\fed on an incline, it is a good practice to
turn the wheels as illustrated.
HEADED DOWNHILL WITH CURB
*1
Turn the wheels into the curb and move the vehicle
forward until the curb side wheel gently touches
the curb. Then apply the par\fing bra\fe. HEADED UPHILL WITH CURB
*2
Turn the wheels away from the curb and allow the
vehicle to move bac\f until the curb side wheel
gently touches the curb. Then apply the par\fing
bra\fe.
HEADED UPHILL OR DOWNHILL, WITHOUT
CURB
*3
Turn the wheels toward the side of the road so the
vehicle will move away from the center of the road
if the vehicle moves. Then apply the par\fing bra\fe.
4. Model with Intelligent Key system:
Place the ignition switch in the “OFF” position.
Model without Intelligent Key system:
Place the ignition switch in the “LOCK” position
and remove the \fey.
NOTE:
For Model with Stop/Start (Idling Stop) System:
Use this system when the vehicle is stopped for
a period of time, for example waiting at stop-
lights.
Stop the engine with the ignition switch when
parking, etc. for an extended period of time.
Starting and driving5-31
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
System malfunction
JVS0032\f
If the “S\bSTEM ERROR” display appears and/or the
ON indicator light on the parking space measurement
switch blinks, have the system checked by a RENAULT
dealer.\bour vehicle was designed to be used to carry
passengers and luggage. RENAULT does not recom-
mend trailer towing, because it places additional loads
on your vehicle’s engine, drivetrain, steering, braking,
and other systems.
CAUTION:
Vehicle damage resulting from towing a trailer is
not covered by the warranty.
WARNING:
.
If the engine is not running or is turned off
while driving, the power assist for the
steering will not work. The steering will be
harder to operate.
. When the electric power steering warning
light illuminates with the engine running, the
power assist for the steering will cease
operation. You will still have control of the
vehicle but the steering will be harder to
operate.
The electric power steering system is designed to
provide power assist while driving to operate the
steering wheel with light force.
When the steering wheel is operated repeatedly or
continuously while parking or driving at a very low
speed, the power assist for the steering wheel will be
reduced. This is to prevent overheating of the electric
power steering system and protect it from getting
damaged. While the power assist is reduced, steering
wheel operation will become heavy. When the
temperature of the electric power steering system
goes down, the power assist level will return to normal.
Avoid repeating such steering wheel operations that
could cause the electric power steering system to
overheat.
\bou may hear a fricative sound when the steering
wheel is operated quickly. However, this is not a
malfunction.
If the electric power steering warning light
illuminates while the engine is running, it may indicate
the electric power steering system is not functioning
properly and may need servicing. Have the electric
power steering system checked by a RENAULT dealer.
(See “Electric power steering warning light” (P.2-14) .)
Starting and driving5-35
TRAILER TOWING
ELECTRIC POWER STEERING
SYSTEM
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
5-36Starting and driving
When the electric power steering warning light
ill\fminates with the engine r\fnning, the power assist
for the steering will cease operation\b Yo\f will still have
control of the vehicle\b However, greater steering effort
is needed, especially in sharp t\frns and at low speeds\bThe brake system has two separate hydra\flic circ\fits\b If
one circ\fit malf\fnctions, yo\f will still have braking
ability at two wheels\b
BRAKE PRECAUTIONS
Vac\f\fm assisted brakes
The brake booster aids braking by \fsing engine
vac\f\fm\b If the engine stops, yo\f can stop the vehicle
by depressing the foot brake pedal\b However, greater
foot press\fre on the foot brake pedal will be req\fired
to stop the vehicle\b The stopping distance will be
longer\b
If the engine is not r\fnning or is t\frned off while driving,
the power assisted brakes will not f\fnction\b Braking
will be harder\b
WARNING:
Do not coast with the engine stopped.
When the brake pedal is depressed slowly and firmly,
yo\f may hear a clicking noise and feel a slight
p\flsation\b This is normal and indicates that the Brake
Assist System is operating\b
Using brakes
Avoid resting yo\fr foot on the foot brake pedal while
driving\b This will overheat the brakes, wear o\ft the
brake linings/pads faster, and increase f\fel cons\fmp-
tion\b
To help red\fce brake wear and to prevent the brakes
from overheating, red\fce speed and downshift to a
lower gear before going down a slope or long grade\b
Overheated brakes may red\fce braking performance
and co\fld res\flt in loss of vehicle control\b
While driving on a slippery s\frface, be caref\fl when
braking, accelerating or downshifting\b Abr\fpt brakingor acceleration co\fld ca\fse the wheels to skid and
res\flt in an accident\b
Wet brakes
When the vehicle is washed or driven thro\fgh water,
the brakes may get wet\b As a res\flt, yo\fr braking
distance will be longer and the vehicle may p\fll to one
side d\fring braking\b
To dry the brakes, drive the vehicle at a safe speed
while lightly depressing the foot brake pedal to heat \fp
the brakes\b Do this \fntil the brakes ret\frn to normal\b
Avoid driving the vehicle at high speeds \fntil the
brakes f\fnction correctly\b
Driving \fphill
When starting on a steep grade, it is sometimes
diffic\flt to operate both the brake and cl\ftch (for
Man\fal Transmission model) \b Apply the parking brake
to hold the vehicle\b Do not slip the cl\ftch\b When ready
to start, slowly release the parking brake while
depressing the accelerator pedal and releasing the
cl\ftch pedal\b
Driving downhill
The engine braking action is effective for controlling
the vehicle while descending hills\b For Man\fal Trans-
mission (MT) model, the shift lever sho\fld be placed in
the lower speed position prior to descending\b For
A\ftomatic Transmission (AT) model, the “1” or “2”
position sho\fld be selected\b For Contin\fo\fsly Variable
Transmission (CVT) model, the “L” position sho\fld be
selected\b
BRAKE SYSTEM
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
BRAKE ASSIST (if equipped)
Whe\f the for\be applied to the brake pedal ex\beeds a
\bertai\f level, the Brake Assist is a\btivated, ge\ferati\fg
greater braki\fg for\be tha\f a \bo\fve\ftio\fal brake
booster eve\f with light pedal for\be.
WARNING:
The Brake Assist is only an aid to assist braking
operation and is not a collision warning or
avoidance device. It is the driver’s responsibility
to stay alert, drive safely and be in control of the
vehicle at all times.
WARNING:
.The Anti-lock Braking System (ABS) is a
sophisticated device, but it cannot prevent
accidents resulting from careless or danger-
ous driving techniques. It can help maintain
vehicle control during braking on slippery
surfaces. Remember that stopping distances
on slippery surfaces will be longer than on
normal surfaces even with ABS. Stopping
distances may also be longer on rough,
gravel or snow covered roads, or if you are
using tire chains. Always maintain a safe
distance from the vehicle in front of you.
Ultimately, the driver is responsible for
safety.
. Tire type and condition may also affect
braking effectiveness.
— When replacing tires, install the speci-
fied size of tires on all four wheels.
— When installing a spare tire, make sure that it is the proper size and type as
specified on the tire placard. (See “Tire
placard” (P.9-8) .)
— For detailed information, see “Tires and
wheels” (P.8-34) .
The A\fti-lo\bk Braki\fg System (ABS) \bo\ftrols the
brakes so the wheels do \fot lo\bk duri\fg hard braki\fg
or whe\f braki\fg o\f slippery surfa\bes. The system
dete\bts the rotatio\f speed at ea\bh wheel a\fd varies
the brake fluid pressure to preve\ft ea\bh wheel from
lo\bki\fg a\fd slidi\fg. By preve\fti\fg ea\bh wheel from
lo\bki\fg, the system helps the driver mai\ftai\f steeri\fg
\bo\ftrol a\fd helps to mi\fimize swervi\fg a\fd spi\f\fi\fg
o\f slippery surfa\bes.
USING SYSTEM
Depress the brake pedal a\fd hold it dow\f. Depress
the brake pedal with firm steady pressure, but do \fot
pump the brakes. The ABS will operate to preve\ft the
wheels from lo\bki\fg up. Steer the vehi\ble to avoid
obsta\bles.
WARNING:
Do not pump the brake pedal. Doing so may
result in increased stopping distances.
SELF-TEST FEATURE
The ABS i\f\bludes ele\btro\fi\b se\fsors, ele\btri\b pumps,
hydrauli\b sole\foids a\fd a \bomputer. The \bomputer has
a built-i\f diag\fosti\b feature that tests the system ea\bh
time you start the e\fgi\fe a\fd move the vehi\ble at a low
speed i\f forward or reverse. Whe\f the self-test
o\b\burs, you may hear a “\blu\fk” \foise a\fd/or feel a
pulsatio\f i\f the brake pedal. This is \formal a\fd does
\fot i\fdi\bate a malfu\f\btio\f. If the \bomputer se\fses a
malfu\f\btio\f, it swit\bhes the ABS off a\fd illumi\fates the
ABS war\fi\fg light o\f the i\fstrume\ft pa\fel. The brake
system the\f operates \formally, but without a\fti-lo\bk
assista\f\be.
If the ABS war\fi\fg light illumi\fates duri\fg the self-test
or while drivi\fg, have the vehi\ble \bhe\bked by a
RENAULT dealer.
Starting and driving5-37
ANTI-LOCK BRAKING SYSTEM
(ABS) (if equipped)
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
5-38Starting and driving
NORMAL OPERATION
The ABS o\ferate\b at \b\feed\b above 5 to 10 km/h (3 to
6 MPH) . The \b\feed varie\b according to road condi-
tion\b.
When the ABS \ben\be\b that one or more wheel\b are
clo\be to locking u\f, the actuator ra\fidly a\f\flie\b and
relea\be\b hydraulic \fre\b\bure. Thi\b action i\b \bimilar to
\fum\fing the brake\b very quickly. You may feel a
\ful\bation in the brake \fedal and hear a noi\be from
under the hood or feel a vibration from the actuator
when it i\b o\ferating. Thi\b i\b normal and indicate\b that
the ABS i\b o\ferating \fro\ferly. However, the \ful\bation
may indicate that road condition\b are hazardou\b and
extra care i\b required while driving.When leaving your vehicle unoccu\fied:
.
Alway\b take the key with you - even when leaving
the vehicle in your own garage.
. Clo\be all window\b com\fletely and lock all door\b.
. Alway\b \fark your vehicle where it can be \been.
Park in a well lit area during the night.
. If the \becurity \by\btem i\b equi\f\fed, u\be it - even for
a \bhort \feriod.
. Never leave children or \fet\b in the vehicle
unattended.
. Never leave valuable\b in\bide the vehicle. Alway\b
take valuable\b with you.
. Never leave the vehicle document\b in the vehicle.
. Never leave article\b on a roof rack. Remove them
from the rack and kee\f and lock them in a \bafe
\flace \buch a\b in\bide the back door.
. Never leave the \b\fare key in the vehicle.WARNING:
.Whatever the condition, drive with caution.
Accelerate and decelerate with great care. If
accelerating or decelerating too fast, the
drive wheels will lose even more traction.
. Allow more stopping distance in cold weath-
er driving. Braking should be started sooner
than on dry pavement.
. Keep at a greater distance from the vehicle
in front of you on slippery roads.
. Wet ice (08C, 328F and freezing rain) , very
cold snow and ice can be slick and very
difficult to drive on. The vehicle will have a
lot less traction or grip under these condi-
tions. Try to avoid driving on wet ice until the
road is salted or sanded.
. Watch for slippery spots (glaring ice) . These
may appear on an otherwise clear road in
shaded areas. If a patch of ice is seen ahead,
brake before reaching it. Try not to brake
while actually on the ice, and avoid any
sudden steering maneuvers.
. Do not use cruise control on slippery roads.
. Snow can trap dangerous exhaust gas under
your vehicle. Keep snow clear of the exhaust
pipe and from around your vehicle.
VEHICLE SECURITY COLD WEATHER DRIVING
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
BATTERY
If the battery is not f\flly charge\b \b\fring extremely col\b
weather con\bitions, the battery fl\fi\b may freeze an\b
\bamage the battery. To maintain maxim\fm efficiency,
the battery sho\fl\b be checke\b reg\flarly. For \betails,
see “Battery” (P.8-23) of this man\fal.
ENGINE COOLANT
If the vehicle is to be left o\ftsi\be witho\ft anti-freeze,
\brain the cooling system, incl\f\bing the engine block.
Refill before operating the vehicle. For \betails, see
“Changing engine coolant” (P.8-9) of this man\fal.
TIRE EQUIPMENT
1. If yo\f have snow tires installe\b on the front/rearwheels of yo\fr vehicle, they sho\fl\b be of the same
size, loa\bing range, constr\fction an\b type (bias,
bias-belte\b or ra\bial) as the rear/front tires.
2. If the vehicle is to be operate\b in severe winter con\bitions, snow tires sho\fl\b be installe\b on all
fo\fr wheels.
3. For a\b\bitional traction on icy roa\bs, st\f\b\be\b tires may be \fse\b. However, some co\fntries, provinces
an\b states prohibit their \fse. Check local, state
an\b provincial laws before installing st\f\b\be\b tires.
Skid and traction capabilities of studded
snow tires, on wet or dry surfaces, may be
poorer than that of non-studded snow tires.
4. Snow chains may be \fse\b if \besire\b. Make s\fre they are the proper size for the tires on yo\fr
vehicle an\b are installe\b accor\bing to the chain
man\ffact\frer’s instr\fctions. (See “Tire chains”
(P.8-34) .)
SPECIAL WINTER EQUIPMENT
It is recommen\be\b that the following items be carrie\b
in the vehicle \b\fring the winter:
.A scraper an\b stiff-bristle\b br\fsh to remove ice
an\b snow from the win\bows.
. A st\fr\by, flat boar\b to be place\b \fn\ber the jack to
give it firm s\fpport.
. A shovel to \big the vehicle o\ft of snow\brifts.
PARKING BRAKE
When parking in the area where the o\ftsi\be tempera-
t\fre is below 08C (328F) , \bo not apply the parking
brake to prevent it from freezing. For safe parking:
.Place the selector lever in the “P” (Park) position
(A\ftomatic Transmission (AT)/Contin\fo\fsly Vari-
able Transmission (CVT) mo\bel) .
. Place the shift lever in the “1” (1st) or “R”
(Reverse) position (Man\fal Transmission (MT)
mo\bel) .
. Sec\frely block the wheels.
CORROSION PROTECTION
Chemicals \fse\b for roa\b s\frface \beicing are extremely
corrosive an\b will accelerate corrosion an\b the
\beterioration of \fn\berbo\by components s\fch as the
exha\fst system, f\fel an\b brake lines, brake cables,
floor pan an\b fen\bers.
In the winter, the underbody must be cleaned
periodically. For additional information, see
“Corrosion protection” (P.7-5) of this manual.
For a\b\bitional protection against r\fst an\b corrosion,
which may be req\fire\b in some areas, cons\flt a
RENAULT \bealer.
Starting and driving5-39
&RQGLWLRQ