coolant level RENAULT PULSE 2012 1.G Owners Manual


> (GLW    0RGHO .$2(0 B5HQDXOW @
2-14Instruments and controls
CAUTION:
Do not continue driving if the alternator belt is
loose, broken or missing.
Door open warning light (if e\fuipped)
\bhen the ignition switch is in the “ON” position, the
door open warning light illuminates if any of the doors
are open or not closed securely.
Electric power steering warning light
\bhen the ignition switch is in the “ON” position, the
electric power steering warning light illuminates. After
starting the engine, the electric power steering warning
light turns off. This indicates the electric power
steering system is operational.
If the electric power steering warning light illuminates
while the engine is running, it may indicate the electric
power steering system is not functioning properly and
may need servicing. Have the electric power steering
system checked by a RENAULT dealer.
\bhen the electric power steering warning light
illuminates with the engine running, the power assist
to the steering will cease operation but you will still
have control of the vehicle. At this time, greater
steering efforts are re\fuired to operate the steering
wheel, especially in sharp turns and at low speeds.
(See “Electric power steering system” (P.5-35) .)
Engine oil pressure warning light
\bhen the ignition switch is in the “ON” position, the
engine oil pressure warning light illuminates. After
starting the engine, the engine oil pressure warning
light turns off. This indicates that the oil pressure
sensors in the engine are operational.
If the engine oil pressure warning light illuminates or
blinks while the engine is running, it may indicate that
the engine oil pressure is low.
Stop the vehicle safely as soon as possible. Stop the
engine immediately and call a RENAULT dealer.
CAUTION:
.Running the engine with the engine oil
pressure warning light illuminated could
cause serious damage to the engine.
. The engine oil pressure warning light is not
designed to indicate a low oil level. The oil
level should be checked using the dipstick.
(See “Engine oil” (P.8-10) .)
High temperature warning light (red)
\bhen the ignition switch is in the “ON” position, the
high temperature warning light illuminates and then
turns off. This indicates that the high temperature
sensor in the engine coolant system is operational.
CAUTION:
If the high temperature warning light illuminates
while the engine is running, it may indicate the
engine temperature is extremely high.
Stop the vehicle safely as soon as possible. If the vehicle is overheated, continuing vehicle
operation may seriously damage the engine.
(See “If your vehicle overheats” (P.6-10) for the
immediate action required.)
Intelligent Key system warning light (if
e\fuipped)
After the ignition switch is placed in the “ON” position,
this light comes on for about 2 seconds and then turns
off.
This light illuminates or blinks as follows:
. The light blinks in yellow when the door is closed
with the Intelligent Key left outside the vehicle and
the ignition switch in the “ACC” or “ON” position.
Make sure that the Intelligent Key is inside the
vehicle (for model without vehicle information
display) .
. The light blinks in green when the Intelligent Key
battery is running out of power. Replace the
battery with a new one (for model without vehicle
information display) . See “Battery” (P.8-23) .
. The light illuminates in yellow when it warns of a
malfunction with the electrical steering lock
system or the Intelligent Key system.
If the warning light illuminates in yellow while the
engine is stopped, it may be impossible to free the
steering lock or to start the engine. If the light comes
on while the engine is running, you can drive the
vehicle. However in these cases, contact a RENAULT
dealer for repair as soon as possible.
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
The Stop/Start System is designed to prevent
unne\fessary fuel \fonsumption, e\bhaust emissions,
and noise during a journey:
.When the vehi\fle \fomes to rest the engine is
automati\fally stopped.
. The engine is then automati\fally restarted before
you are ready to drive away.
CAUTION:
At the end of the journey the engine must be
stopped and ignition switch be turned off. Lock
the vehicle as normal. Turning the ignition OFF
will shut down all electrical systems. Failure to
do this may result in a flat battery.
NORMAL OPERATION
The Stop/Start System stops the engine and will
automati\fally restart the engine. The Stop/Start
indi\fator light is shown in the meter.
The Stop/Start System will automati\fally stop
the engine when all the following \fonditions
are valid.
For MT model
.The shift lever is in Neutral position.
. The \flut\fh pedal is fully released.
. The vehi\fle speed is below about 2 km/h (1
MPH) .
. The driver’s seat belt is fastened.
. The Intelligent Key is in the vehi\fle.
. The driver’s door is \flosed.
For CVT model
. The sele\ftor lever is in the "D" (Drive) or "N"
(Neutral) position. .
The brake pedal is depressed.
. The vehi\fle is stopped.
. The driver’s seat belt is fastened.
. The driver’s door is \flosed.
NOTE:
The following conditions must also be satisfied
before the engine is automatically stopped. If
the engine does not stop this does not indicate a
malfunction in the system:
. The engine coolant temperature is at normal
operating levels.
. The vehicle has driven some distance since
engine start.
. The battery voltage and temperature are
within normal levels.
. The hood is closed.
. The steering wheel is not being turned.
. The system is not in front defogger mode.
(automatic air conditioner)
. The mode dial is not in front defogger mode.
(manual air conditioner)
. The rear window defogger is not operated.
NOTE:
The engine will not restart if the brake pedal is
released while the Stop/Start System is acti-
vated under the following condition:
. The selector lever is in the "P" (Park) position
(for CVT model) .
When the Stop/Start System indi\fator light is
displayed the engine starts running automa-
ti\fally under at least one of the following
\fonditions.
.The \flut\fh pedal is depressed (for MT model) .
. The brake pedal is released with the sele\ftor lever
in the "D"(Drive) or "N"(Neutral) position (for CVT
model) .
. The sele\ftor lever is pla\fed in the "L"(Low) ,
"D"(Drive) or "R"(Reverse) position from the "N"
or "P" position (for CVT model) .
. The driver’s seat belt is unfastened, or the driver’s
door is open (for CVT model) .
. The brake pedal is repeatedly pressed (to maintain
vehi\fle braking performan\fe) .
. The brake pedal is strongly depressed and then
released with the sele\ftor lever in the "P" (Park)
position, resulting in de\freased va\fuum pressure
of the brake booster (for CVT model) .
. The battery voltage be\fomes low (due to ele\ftri\fal
load from other vehi\fle systems like headlights,
heaters, et\f., or au\biliary devi\fes \fonne\fted to the
12 volt so\fket inside the vehi\fle) .
. The vehi\fle speed is above about 2 km/h (1
MPH) .
. The system is in front defogger mode. (automati\f
air \fonditioner)
. The mode dial is in front defogger mode. (manual
air \fonditioner)
. The rear window defogger is operated.
NOTE:
The following conditions will prevent the Stop/
Start System from automatically restarting the
engine. Starting the engine by the ignition
switch is then necessary:
Starting and driving5-21
STOP/START SYSTEM (if equipped
for Europe)
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
6-10In case of emergency
Do not attempt to start the engine by p\fshing the
vehicle\b
CAUTION:
.Automatic Transmission (AT)/Continuously
Variable Transmission (CVT) model cannot
be started by pushing. Attempting to do so
may cause damage to the transmission.
. Three-way catalyst equipped model should
not be started by pushing. Attempting to do
so may cause damage to the catalyst.
. Never try to start the engine by towing.
When the engine starts, the forward surge
could cause the vehicle to collide with the
towing vehicle.
. Stop/Start (Idling Stop) System equipped
model cannot be started by pushing the
vehicle.
WARNING:
.Never continue driving if your vehicle over-
heats. Doing so could cause a vehicle fire.
. Never open the hood if steam is coming out.
. Never remove the radiator cap while the
engine is hot. If the radiator cap is removed
when the engine is hot, pressurized hot
water will spurt out and possibly cause
burning, scalding or serious injury.
. If steam or coolant is coming from the
engine, stand clear of the vehicle to prevent
getting burned.
. Be careful not to allow your hands, hair,
jewelry or clothing to come into contact with,
or to get caught in the cooling fan or drive
belts. The engine cooling fan will start at any
time.
If yo\fr vehicle is overheating (indicated by the high
temperat\fre indicator) , or if yo\f feel a lack of engine
power, detect \fn\fs\fal noise, etc\b, take the following
steps:
1\b Safely move the vehicle off the road away from traffic\b
2\b T\frn on the hazard indicator flasher lights\b
3\b Apply the parking brake\b
4\b A\ftomatic Transmission (AT)/Contin\fo\fsly Vari- able Transmission (CVT) model: Move the selector
lever to the “P” (Park) position\b
Man\fal Transmission (MT) model: Move the shift
lever to the “N” (Ne\ftral) position\b
DO NOT STOP THE ENGINE . 5\b Open all windows\b
6\b T\frn off the air conditioner\b Set the temperat\fre
control to maxim\fm hot and fan control to
maxim\fm speed\b
7\b Get o\ft from the vehicle\b
8\b Vis\fally inspect and listen for steam or coolant escaping from the radiator before opening the
hood\b Wait \fntil no steam or coolant can be seen
before proceeding\b
9\b Open the engine hood\b
10\b Vis\fally inspect if the cooling fan is r\fnning\b
11\b Vis\fally inspect the radiator and radiator hoses for leakage\b
If the cooling fan is not r\fnning or the coolant is
leaking, stop the engine\b
12\b After the engine cools down, check the coolant level in the reservoir with the engine r\fnning\b Do
not open the radiator cap.
13\b Add coolant to the reservoir if necessary\b
Have yo\fr vehicle inspected/repaired at a RENAULT
dealer\b
PUSH STARTING IF YOUR VEHICLE OVERHEATS
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
Tires*:
Check the pressure with a gauge often and alwa\fs
prior to long distance trips. If necessar\f, ad\bust the
pressure in all tires, including the spare, to the
pressure specified. Check carefull\f for damage, cuts
or excessive wear.
Tire rotation*:
Tires should be rotated ever\f 10,000 km (6,000
miles) . However, the timing for tire rotation ma\f var\f
according to \four driving habits and the road surface
conditions.
Wheel alignment and balance (for Europe):
If the vehicle should pull to either side while driving on
a straight and level road, or if \fou detect uneven or
abnormal tire wear, there ma\f be a need for wheel
alignment.
If the steering wheel or seat vibrates at normal highwa\f
speeds, wheel balancing ma\f be needed.
Windshield:
Clean the windshield on a regular basis. Check the
windshield at least ever\f six months for cracks or other
damage. Have a damaged windshield repaired b\f a
qualified repair facilit\f.
Wiper blades*:
Check for cracks or wear if the\f do not wipe properl\f.
Inside vehicle
The maintenance items listed here should be checked
on a regular basis, such as when performing periodic
maintenance, cleaning the vehicle, etc.Accelerator pedal:
Check the pedal for smooth operation and make sure
that the pedal does not catch or require uneven effort.
Keep the floor mats awa\f from the pedal.
Brake pedal*:
Check the pedal for smooth operation and make sure
that it has the proper distance under it when
depressed full\f. Check the brake booster function.
Keep the floor mats awa\f from the pedal.
Parking brake*:
Check that the pedal/lever has the proper distance of
travel.
Seat belts:
Check that all parts of the seat belt s\fstem (for
example, buckles, anchors, ad\busters and retractors)
operate properl\f and smoothl\f, and that the\f are
installed securel\f. Check the belt webbing for cuts,
fra\fing, wear or damage.
Steering wheel:
Check for changes in the steering conditions, such as
excessive free pla\f, hard steering or strange noises.
Warning lights and chimes:
Make sure that all warning lights and chimes are
operating properl\f.
Windshield defogger:
Check that the air comes out of the defogger outlets
properl\f and in good quantit\f when operating the
heater or air conditioner.
Windshield wiper and washer*:
Check that the wipers and washer operate properl\f
and that the wipers do not streak.
Under hood and vehicle
The maintenance items listed here should be checked
periodicall\f (for example, each time \fou check the
engine oil or refuel) .
Battery*:
Check the fluid level in each cell. It should be between
the UPPER and LOWER levels. Vehicles operated in
high temperatures or under severe conditions require
frequent checks of the batter\f fluid level.
Brake and clutch fluid level*:
Make sure that the brake and clutch fluid level is
between the MAX and MIN lines on the reservoir.
Engine coolant level*:
Check the coolant level when the engine is cold.
Engine drive belts*:
Make sure the drive belts are not fra\fed, worn, cracked
or oil\f.
Engine oil level*:
Check the level on the dipstick after parking the vehicle
on a level surface and turning off the engine.
Fluid leaks:
Check under the vehicle for fuel, oil, water or other fluid
leaks after the vehicle has been parked for a while.
Water dripping from the air conditioner after use is
normal. If \fou should notice an\f leaks or if fuel fumes
are evident, check for the cause and have it corrected
immediatel\f.
Maintenance and do-it-yourself8-3
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
8-4Maintenance and do-it-yourself
Window washer fluid*:
Check that there is adequate fluid in the reser\foir.
M\bINTEN\bNCE PREC\bUTIONS
When performing any inspection or maintenance work
on your \fehicle, always take care to pre\fent serious
accidental injury to yourself or damage to the \fehicle.
The following are general precautions which should be
closely obser\fed.
WARNING:
.Park the vehicle on a level surface, apply the
parking brake securely and block the wheels
to prevent the vehicle from moving. Move
the selector lever to the “P”(Park) position
or the shift lever to the “N”(Neutral) position.
. Be sure the ignition switch is in the “OFF”or
“LOCK” position when performing any parts
replacement or repairs.
. Do not work under the hood while the
engine is hot. Always turn off the engine
and wait until it cools down.
. If you must work with the engine running,
keep your hands, clothing, hair and tools
away from moving fans, belts and any other
moving parts.
. It is advisable to secure or remove any loose
clothing and any jewelry, such as rings,
watches, etc. before working on your vehi-
cle.
. If you must run the engine in an enclosed
space such as a garage, be sure there is
proper ventilation for exhaust gases to
escape. .
Never get under the vehicle while it is
supported by a jack.
. Keep smoking materials, flame and sparks
away from fuel and the battery.
. Never connect or disconnect either the
battery or any transistorized component
connector while the ignition switch is in the
“ON” position.
. On gasoline engine models with the Multi-
port Fuel Injection (MFI) system, the fuel
filter and fuel lines should be serviced by a
RENAULT dealer because the fuel lines are
under high pressure even when the engine is
turned off.
. Your vehicle is equipped with an automatic
engine cooling fan. It may come on at any
time without warning, even if the ignition
switch is in the “OFF” position and the
engine is not running. To avoid injury, always
disconnect the negative battery cable before
working near the fan.
. Always wear eye protection whenever you
work on your vehicle.
. Never leave the engine or the transmission
related component harness connector dis-
connected while the ignition switch is in the
“ON” position.
. Avoid direct contact with used engine oil and
coolant. Improperly disposed engine oil,
engine coolant, and/or other vehicle fluids
can hurt the environment. Always conform to
local regulations for disposal of vehicle
fluids.
This “8. Maintenance and do-it-yourself” section
pro\fides instructions regarding only those items which are relati\fely easy for an owner to perform.
You should be aware that incomplete or improper
ser\ficing may result in operating difficulties or ex-
cessi\fe emissions, and could affect your warranty
co\ferage.
If in doubt about any servicing, have it
done by a RENAULT dealer.
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
Outside temperaturedown to Composition
8C 8FEngine
coo\fant
(concentra- ted) \beminera-
\fized or dis- ti\f\fed water
í15 5 30% 70%
í35 í30 50% 50%
The use of other types of coo\fant so\futions may
damage the engine coo\fing system.
The radiator is equipped with a pressure cap. To
prevent engine damage, use on\fy a Genuine RENAULT
radiator cap or its equiva\fent when rep\facement is
required.CHECKING ENGINE COOLANT LEVEL
HR12\b\bR, HR12\bE and HR15\bE engine
mode\f
S\bI2571HR12DDR, HR12DE and HR15DE engineCheck the coo\fant \feve\f in the reservoir when the
engine is co\fd. If the coo\fant \feve\f is be\fow the MIN
\feve\f
*2, add coo\fant up to the MAX \feve\f*1. If the
reservoir is empty, check the coo\fant \feve\f in the
radiator when the engine is cold. If there is
insufficient coo\fant in the radiator, fi\f\f the radiator with
coo\fant up to the fi\f\fer opening and a\fso add it to the
reservoir up to the MAX \feve\f
*1.
If the cooling system frequently requires cool-
ant, have it checked by a RENAULT dealer.
K9K engine mode\f
S\bI2712K9K engineCheck the coo\fant \feve\f in the reservoir when the
engine is co\fd. If the coo\fant \feve\f is be\fow the MIN
\feve\f
*2, add coo\fant up to the MAX \feve\f*1.
If the cooling system frequently requires cool-
ant, have it checked by a RENAULT dealer.
CHANGING ENGINE COOLANT
Contact a RENAULT dea\fer if rep\facement is required.
Major engine coo\fing system repair shou\fd be per-
formed by a RENAULT dea\fer. The service procedures
can be found in the appropriate RENAULT Service
Manua\f.
Improper servicing can resu\ft in reduced heater
performance and engine overheating.
WARNING:
. To avoid being scalded, never change the
coolant when the engine is hot.
. Never remove the radiator cap when the
engine is hot. Serious burns could be caused
by high pressure fluid escaping from the
radiator.
Maintenance and do-it-yourself8-9
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
8-10Maintenance and do-it-yourself
.Avoid direct skin contact with used coolant.
If skin contact is made, wash thoroughly
with soap or hand cleaner as soon as
possible.
. Keep coolant out of reach of children and
pets.
Engine coolant must be dis\fosed of \fro\ferly\b Check
your local regulations\bCHECKING ENGINE OIL LEVEL
SDI2572HR12DDR, HR12DE and HR15DE engine
SDI2713K9K engine1\b Park the vehicle on a level surface and a\f\fly the \farking brake\b
2\b Start the engine and warm it u\f until the engine tem\ferature reaches the normal o\ferating tem-
\ferature (a\f\froximately 5 minutes) \b
3\b Sto\f the engine\b
4\b Wait at least 10 minutes for the engine oil to drain back to the oil \fan\b
5\b Remove the di\fstick and wi\fe it clean\b 6\b Reinsert the di\fstick all the way\b
7\b Remove the di\fstick and check the oil level\b It
should be within the range
*C\b
8\b If the oil level is below
*A, remove the oil filler ca\f
and \four the recommended oil into the o\fening\b
Do not overfill
*B\b
When filling the engine oil, do not remove
the dipstick.
9\b Recheck the oil level with the di\fstick\b
It is normal to add some oil between oil
maintenance intervals or during the break-in
period, depending on the severity of operat-
ing conditions.
CAUTION:
The oil level should be checked regularly.
Operating your vehicle with an insufficient
amount of oil can damage the engine, and such
damage is not covered by warranty.
CHANGING ENGINE OIL AND OIL FILTER
WARNING:
.Used oil must be disposed of properly. Never
pour or dump oil into the ground, canals,
rivers, etc. It should be disposed of at proper
waste facilities. RENAULT recommends hav-
ing your oil changed by a RENAULT dealer.
. Be careful not to burn yourself, as the
engine oil may be hot.
. Prolonged and repeated contact with used
engine oil may cause skin cancer.
. Avoid direct skin contact with used oil. If
contacted, wash thoroughly with soap or
ENGINE OIL
&RQGLWLRQ