torque RENAULT PULSE 2012 1.G Owners Manual


> (GLW    0RGHO .$2(0 B5HQDXOW @
WARNING:
.Never use wheel nuts which are not provided
with your vehicle. Incorrect wheel nuts or
improperly tightened wheel nuts may cause
the wheel to become loose or come off. This
could cause an accident.
. Never use oil or grease on the wheel studs
or nuts. This may cause the wheel nuts to
become loose.
. The T-type spare tire is designed for emer-
gency use only.
1. Clean any mud or dirt from the surface \fetween the wheel and hu\f.
2. Carefully put the spare tire on and ti\bhten the wheel nuts with your fin\bers. Check that all the
wheel nuts contact the wheel surface horizontally.
3. Ti\bhten the wheel nuts alternately and evenly, more than 2 times in the sequence illustrated (
*1-*4) , with the wheel nut wrench, until they are
ti\bht.
4. Lower the vehicle slowly until the tire touches the \bround.
5. Ti\bhten the wheel nuts securely, with the wheel nut wrench, in the sequence illustrated.
6. Lower the vehicle completely.
Tighten the wheel nuts to the specified torque
with a torque wrench as soon as possible. Wheel nut tightening torque:108 N·m (11 kg-m, 80 ft-lb)
The wheel nuts must be kept tightened to
specification at all times. It is recommended
that the wheel nuts be tightened to specification
at each lubrication interval.
WARNING:
Retighten the wheel nuts when the vehicle has
been driven for 1,000 km (600 miles) . (also in
cases of a flat tire, etc.)
Stowin\b dama\bed tire and tools
WARNING:
. Be sure that the tire, jack and tools used are
properly stored after use. Such items can
become dangerous projectiles in an accident
or sudden stop.
. The T-type spare tire is designed for emer-
gency use only.
1. Securely store the dama\bed tire, jack and tools used in the stora\be area.
2. Replace the spare tire cover and the floor cover.
3. Close the \fack door.
REPAIRING FLAT TIRE (for model with
emer\bency tire puncture repair kit)
The emer\bency tire puncture repair kit is supplied with
the vehicle instead of a spare tire. This repair kit must
\fe used for temporarily fixin\b a minor tire puncture.
After usin\b the repair kit, see a RENAULT dealer as
soon as possi\fle for tire inspection and repair/
replacement.
CAUTION:
. RENAULT recommends using only Genuine
RENAULT Emergency Tire Sealant provided
with your vehicle. Other tire sealants may
damage the valve stem seal which can cause
the tire to lose air pressure. .
Do not use the emergency tire puncture
repair kit provided with your vehicle on other
vehicles.
. Do not use the emergency tire puncture kit
for a purpose other than to inflate and check
the tire pressure for the vehicle.
. Use the emergency tire puncture kit only on
DC12V.
. Keep water and dust off the emergency tire
puncture kit.
. Do not disassemble or modify the emer-
gency tire puncture kit.
. Do not galvanize the emergency tire punc-
ture kit.
. Do not use the emergency tire puncture
repair kit under the following conditions.
Contact a RENAULT dealer or professional
road assistance.
— when the sealant has passed its expira-
tion date (shown on the label attached
to the bottle)
— when the cut or the puncture is approxi- mately 6 mm (0.25 in) or longer
— when the side of the tire is damaged
— when the vehicle has been driven with a considerable loss of air from the tire
— when the tire is completely displaced inside or outside the rim
— when the tire rim is damaged
— when two or more tires are flat
In case of emergency6-5
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
8-12Maintenance and do-it-yourself
JVM0001XHR15DE engine model1. Oil filler cap
2. Oil \frain plug
\b. Oil filter
1. Park the vehicle on a level surface an\f apply the parking brake.
2. Start the engine an\f warm it up until the engine temperature reaches the normal operating tem-
perature (approximately 5 minutes) .
\b. Stop the engine.
4. Wait at least 10 minutes for the engine oil to \frain back to the oil pan. 5. Place a large \frain pan un\fer the \frain plug.
6. Remove the \frain plug with a wrench.
7. Remove the oil filler cap an\f completely \frain the
oil.
If the oil filter is to be change\f, remove an\f
replace it at this time. (See “Engine oil filter
replacement (HR12DDR, HR12DE an\f HR15DE
engine mo\fels)” (P.8-12) .)
8. Clean an\f reinstall the \frain plug an\f new washer. Securely tighten the \frain plug with a wrench. Do
not use excessive force.
Drain plug tightening torque:29 to 39 N·m
(3.0 to 4.0 kg-m, 22 to 29 ft-lb)
9. Refill the recommen\fe\f engine oil an\f quantity. (See “Recommen\fe\f fuel/lubricants an\f capaci-
ties” (P.9-2) .)
When filling the engine oil, do not remove
the dipstick.
10. Securely install the oil filler cap.
11. Start the engine.
12. Check the \frain plug for any sign of leakage.
1\b. Check the engine oil level accor\fing to the proper proce\fure. (See “Checking engine oil level” (P.8-
10) .)
Engine oil filter replacement (HR12DDR,
HR12DE an\f HR15DE engine mo\fels)
JVM0059XHR12DDR engine model
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
SDI2578HR12DE engine modelJVM0001XHR15DE engine model1. Oil fille\f cap
2. Oil \b\fain plug
3. Oil filte\f
1. Pa\fk the vehicle on a level su\fface an\b apply the pa\fking b\fake.
2. Tu\fn the engine off.
3. D\fain the engine oil acco\f\bing to the p\fope\f p\foce\bu\fe. (See “Engine oil \feplacement
(HR12DDR, HR12DE an\b HR15DE engine mo\b-
els)” (P.8-11) .) 4. Loosen the oil filte\f with an oil filte\f w\fench.
Depen\bing on the engine mo\bel, a special cap
type w\fench may be \fequi\fe\b. See a RENAULT
\beale\f fo\f mo\fe info\fmation.
5. Remove the oil filte\f by tu\fning it by han\b.
6. Wipe the engine oil filte\f mounting su\fface with a clean cloth.
Be su\fe to \femove any ol\b gasket \femaining on the
mounting su\fface.
7. Apply the new engine oil to the gasket of the new oil filte\f.
8. Sc\few in the oil filte\f until a slight \fesistance is felt, an\b then tighten an a\b\bitional 2/3 of tu\fn to
secu\fe the oil filte\f.
Oil filter tightening torque:15 to 20 N·m (11 to 14 ft-lb)
9. Refill the engine oil. (See “Engine oil \feplacement (HR12DDR, HR12DE an\b HR15DE engine mo\b-
els)” (P.8-11) .)
10. Sta\ft the engine an\b check fo\f leakage a\foun\b the oil filte\f. Co\f\fect as \fequi\fe\b.
11. Tu\fn the engine off an\b wait seve\fal minutes.
12. Check the engine oil level acco\f\bing to the p\fope\f p\foce\bu\fe. (See “Checking engine oil level” (P.8-
10) .)
Maintenance and do-it-yourself8-13
&RQGLWLRQ


> (GLW    0RGHO .$2(0 B5HQDXOW @
8-14Maintenance and do-it-yourself
Engine oil and filter replacement \fK9K engine
model)
\bDI2472
1. Oil drain plug
2. Oil filter
1. Place a large drain pan under the drain plug.
2. Remove the drain plug with a wrench.
3. Remove the oil filler cap and completely drain the oil.
If the oil filter is to be changed, remove and
replace it at this time.
CAUTION:
Waste oil must be disposed of properly. Check
your local regulations.
4. Loosen the oil filter with an oil filter wrench.
5. Remove the oil filter by turning it by hand.
6. Wipe the entire oil filter mounting surface with aclean cloth.
Be sure to remove any old gasket remaining on the
mounting surface. 7. Apply new engine oil to the gasket on the new oil
filter.
8. \bcrew in the oil filter until a slight resistance is felt, and then tighten an additional 3/4 of a turn to
secure the filter.
Oil filter tightening torque:16 to 20 N·m (1.6 to 2.0 kg-m, 12 to 15 ft-lb)
9. Clean and reinstall the drain plug and new washer. \becurely tighten the drain plug with a wrench. Do
not use excessive force.
Drain plug tightening torque:16 to 24 N·m (1.6 to 2.4 kg-m, 12 to 18 ft-lb)
10. Refill the recommended engine oil and quantity. \f\bee “Recommended fuel/lubricants and capaci-
ties” \fP.9-2) .)
11. \becurely install the oil filler cap.
12. \btart the engine.
13. Check the drain plug and the oil filter for any sign of leakage.
14. Dispose of the used oil in the proper manner. Check your local regulations.
15. Check the engine oil level according to the proper procedure. \f\bee “Checking engine oil level” \fP.8-
10) .)
After operation
1. Install the engine undercover \fif removed) intoposition as the following steps.
a. Pull the center of each plastic clip out.
b. Hold the engine undercover into position.
c. Insert the clips through the undercover into thehole in the frame, then push the center of the
clips in to lock the clips in place. d. \bcrew in the bolts, then tighten them.
2. Lower the vehicle carefully to the ground.
PROTECT ENVIRONMENT
It is illegal to pollute drains, watercourses and soil. Use
authorized waste collection facilities, including civil
amenity sites and garages providing facilities for
disposal of used oil and used oil filters. If in doubt,
contact your local authority for advice on disposal.
The regulations concerning the pollution of the
environment will vary from country to country.
&RQGLWLRQ