ignition RENAULT SCENIC 2010 J95 / 3.G Engine And Pheripherals DCM 1.2 Injection Workshop Manual

13B-225V10 MR-372-J84-13B100$190.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
TEST 12 Turbocharger
IMPORTANT
Perform these checks without removing the turbocharger and with the vehicle ignition switched off.
Checking the turbocharger shaft
WARNING
Observe the following safety precautions:
–wear high temperature protective gloves when the engine is hot,
–do not wear oversize or baggy clothing or hanging jewellery,
–watch out for possible triggering of the motor-driven cooling fan unit and the operation of the accessories belt
or belts.
Note:
The turbocharger shaft is the shaft that connects the compressor wheel and the turbine wheel.
Depending on the vehicle type, the best visual access will be either from above or from below.
Disconnect the air pipe located between the turbocharger and the air filter.
Wearing gloves, check the operation of the turbocharger shaft by turning the vanes manually without forcing.
Does the shaft have a kickdown point in rotation?
Does the compressor wheel touch the casing of the turbocharger?
If for these 2
questions the
response is NOIf YES for one of these 2 questions
Replace the turbocharger (see MR 364 (Mégane II), 370 (Scénic II) 392
(Clio III), 385 (Modus), 411 (New Twingo) or 417 (Kangoo II),
Mechanical, 12B, Turbocharging, Turbocharger: Removal -
Refitting and Technical Note 3938A, Broken turbocharger:
Replacement instructions).
A
DCM1.2_V48_TEST12/DCM1.2_V4C_TEST12/DCM1.2_V50_TEST12/DCM1.2_V54_TEST12/DCM1.2_V58_TEST12/DCM1.2_V5C_TEST12

13B-233V10 MR-372-J84-13B100$190.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
TEST 14 Accelerator pedal check
Can the accelerator pedal be fully
depressed and does it return fully?Check that there are no obstructions between the floor
and the accelerator pedal, and check that the latter has no
points of resistance.
Vehicle under + after ignition feed.
Measure the voltage between
connections 3LR and 3LT of
component 921.Check the continuity and insulation of connections 3LR
and 3LT between components 921 and 120.
If the connection is faulty and there is a repair method
(see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring,
otherwise replace it. Expected result:
4.75 V < X < 5.25 V
Vehicle under + after ignition feed.
Fully depress the accelerator pedal
and measure the voltage between
connections 3LS and 3LT of
component 921.Check the continuity and insulation of connection 3LS
between components 921 and 120.
If the connection is faulty and there is a repair method
(see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If these checks are correct, replace the accelerator pedal
sensor (see MR 392 (Clio III), MR 364 (Mégane II), MR 370
(Scénic II), MR 417 (Kangoo 2), Mechanical, 37A,
Mechanical component controls, Accelerator pedal:
Removal – Refitting) or (see MR 385 (Modus), MR 411
(New Twingo), Mechanical, 37A, Mechanical
component controls, Accelerator brake pedal
assembly: Removal – Refitting). Expected result:
3.94 < X < 4.56 V
Vehicle under + after ignition feed.
Accelerator pedal in no load position,
measure the voltage between
connections 3LS and 3LT of
component 921.Replace the accelerator pedal sensor (see MR 392
(Clio III), MR 364 (Mégane II), MR 370 (Scénic II), MR 417
(Kangoo 2), Mechanical, 37A, Mechanical component
controls, Accelerator pedal: Removal – Refitting)
or (see MR 385 (Modus), MR 411 (New Twingo),
Mechanical, 37A, Mechanical component controls,
Accelerator brake pedal assembly: Removal –
Refitting). Expected result:
0.66 V < X < 0.84 VNO
YES
NO
YES
NO
YES
NO
YES
A
DCM1.2_V48_TEST14/DCM1.2_V4C_TEST14/DCM1.2_V50_TEST14/DCM1.2_V54_TEST14/DCM1.2_V58_TEST14/DCM1.2_V5C_TEST14

13B-234V10 MR-372-J84-13B100$190.mif
DIESEL INJECTION
Fault finding – Tests13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
TEST 14
CONTINUED
Vehicle under + after ignition feed.
Measure the voltage between
connections 3LU and 3LV of
component 921.Check the continuity and insulation of connections 3LU
and 3LV between components 921 and 120.
If the connection is faulty and there is a repair method
(see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring,
otherwise replace it. Expected result:
4.75 V < X < 5.25 V
Vehicle under + after ignition feed. Fully
depress the accelerator pedal
and measure the voltage between
connections 3LW and 3LV of
component 921.Check the continuity and insulation of connection 3LW
between components 921 and 120.
If the connection is faulty and there is a repair method
(see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If these checks are correct, replace the accelerator pedal
sensor (see MR 392 (Clio III), MR 364 (Mégane II), MR 370
(Scénic II), MR 417 (Kangoo 2), Mechanical, 37A,
Mechanical component controls, Accelerator pedal:
Removal – Refitting) or (see MR 385 (Modus), MR 411
(New Twingo), Mechanical, 37A, Mechanical component
controls, Accelerator brake pedal assembly: Removal –
Refitting). Expected result:
2.16 < X < 2.38 V
Vehicle under + after ignition feed.
Accelerator pedal in no load position,
measure the voltage between
connections 3LW and 3LV of
component 921.Replace the accelerator pedal sensor (see MR 392
(Clio III), MR 364 (Mégane II), MR 370 (Scénic II), MR 417
(Kangoo 2), Mechanical, 37A, Mechanical component
controls, Accelerator pedal: Removal – Refitting) or
(see MR 385 (Modus), MR 411 (New Twingo),
Mechanical, 37A, Mechanical component controls,
Accelerator brake pedal assembly: Removal –
Refitting). Expected result:
0.32 < X < 0.42 V
Contact the Techline
A
NO
YES
NO
YES
NO
YES

13B-238V10 MR-372-J84-13B100$210.mif
DIESEL INJECTION
Fault finding – Fault finding charts13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ALP2
CONTINUED 1
Does the starter motor operate correctly
(minimum engine speed = 200 rpm)?Carry out the necessary repairs
Is the compression in order? Carry out the necessary repairs
Using the diagnostic tool, check that the injector codes (C2I) are correctly entered on the identification screen.
If not, configure the correct injector codes using command SC002 Enter injector codes.

Is PR038 Rail pressure less than 50 bar under
+ after ignition feed?Apply the fault finding procedure for DF007 Rail
pressure sensor circuit.
Check the low pressure circuit: run TEST 1 Low pressure circuit check.
Check the injectors: run TEST 3 Injector check.
A
NO
YES
NO
YES
YES
NO
B