heating RENAULT SCENIC 2010 J95 / 3.G Engine And Pheripherals DCM 1.2 Injection Owner's Manual

13B-136
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET022LOW-SPEED FAN REQUEST
STATUS DEFINITION"ACTIVE": The low speed fan assembly request is active.
"INACTIVE": The low speed fan assembly request is not active.
Conformity check with engine stopped, ignition on or engine running
ACTIVEThe injection computer requests the activation of the low speed GMV when:
–the engine coolant temperature is above 96˚C,
–the injection computer has system faults that could lead to the engine overheating,
–the air conditioning is switched on by the driver.
When the low-speed fan assembly is supplied:
–status ET022 Low speed fan request becomes ACTIVE.
Fan assembly activation is controlled by the UPC.
INACTIVEThe low-speed fan assembly stops when:
–the engine coolant temperature is below 94˚C,
–no fault which could cause engine overheating is present in the injection
system.
–the air conditioning is not switched on by the driver.
Fan assembly activation is controlled by the UPC.
DCM1.2_V48_ET022/DCM1.2_V4C_ET022/DCM1.2_V50_ET022/DCM1.2_V54_ET022/DCM1.2_V58_ET022/DCM1.2_V5C_ET022

13B-137
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET023FAST IDLE SPEED REQUEST
STATUS DEFINITION"PRESENT": The fast idle speed request is present.
"ABSENT": The fast idle speed request is not present.
NOTESSpecial notes:
The idle speed setpoint is dependent on:
–the coolant temperature,
–the emission control programs,
–air conditioning requirements,
–the electrical consumers,
–the battery voltage,
–the gear engaged.
–use of command SC041 "Changing commercial vehicle idle speed" (Kangoo 2)
Conformity check with engine stopped, ignition on or engine running
PRESENTStatus is "PRESENT" when there is an engine load:
–inconsistency between the positions of the brake and accelerator pedals,
–coolant temperature < 80
°C or > 89 °C,
–heating and air conditioning system deactivated,
–with electrical consumers,
–the battery voltage is incorrect.
–or after running command SC041 "Changing commercial vehicle idle speed"
(Kangoo 2)
ABSENTStatus is "ABSENT" when there is no engine load:
–coolant temperature = 80
°C,
–heating and air conditioning system deactivated,
–without electrical consumers,
–the battery voltage is correct.
DCM1.2_V48_ET023/DCM1.2_V4C_ET023/DCM1.2_V50_ET023/DCM1.2_V54_ET023/DCM1.2_V58_ET023/DCM1.2_V5C_ET023

13B-148
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
ET079AIR CONDITIONING PRESENT
STATUS DEFINITIONYES: This status indicates that air conditioning is present on the vehicle.
NO: This status indicates that air conditioning is not present on the vehicle.
NOTESThe heating and air conditioning system is present depending on the vehicle's
equipment level.
Conformity check: Engine stopped, ignition on or engine running.
YES or NO, depending on the vehicle equipment.
DCM1.2_V48_ET079/DCM1.2_V4C_ET079/DCM1.2_V50_ET079/DCM1.2_V54_ET079/DCM1.2_V58_ET079/DCM1.2_V5C_ET079

13B-150
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
*RCH = Passenger Compartment Heating Resistors
ET111SET NUMBER OF PASSENGER COMPARTMENT HEATING RESISTORS
STATUS DEFINITIONThis status indicates that the injection computer is blocking any change to the number
of passenger compartment air heating resistors active (active ones are not cut off, but
no more can be added). This freeze in the number of heating resistors is in response to
vehicle needs (availability of power, need for torque etc.).
Conformity check: Engine stopped and ignition on, or engine running and engine coolant
temperature > 80
°C
YESDepending on the requirements of the injection system (e.g. torque reduction, power
requirements), the injection computer sets the number of activated passenger
compartment heating resistors (no more or no fewer than required).
Status ET111 becomes YES when the number of activated passenger compartment
heating resistors is set by the injection computer.
NODepending on the requirements of the injection system (e.g. torque reduction, power
requirements), the injection computer sets the number of activated passenger
compartment heating resistors (no more or no fewer than required). Status ET111
becomes NO if the number of passenger compartment heating resistors engaged can
be freely controlled by the UCH.
DCM1.2_V48_ET111/DCM1.2_V4C_ET111/DCM1.2_V50_ET111/DCM1.2_V54_ET111/DCM1.2_V58_ET111/DCM1.2_V5C_ET111

13B-151
AFTER REPAIRDeal with any faults. Clear the faults from the computer memory.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
V10 MR-372-J84-13B100$150.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
*RCH = Passenger Compartment Heating Resistors
ET112PASSENGER COMPARTMENT HEATING RESISTOR CUT-OFF
STATUS DEFINITIONThis status indicates that the injection computer is blocking activation of all passenger
compartment air heating resistors due to vehicle needs (availability of power, need for
torque, injection defect mode or heating and ventilation etc.).
Conformity check: Engine stopped and ignition on, or engine running and engine coolant
temperature > 80
°C
YESDepending on the requirements of the injection system (e.g. torque reduction, power
requirements), the injection computer cuts off the passenger compartment heating
resistors.
Status ET112 becomes YES when the passenger compartment heating resistors are cut
off by the injection computer.
NODepending on the requirements of the injection system (e.g. torque reduction, power
requirements), the injection computer cuts off the passenger compartment heating
resistors.
Status ET112 becomes NO when the passenger compartment heating resistors can be
freely controlled by the UCH.
DCM1.2_V48_ET112/DCM1.2_V4C_ET112/DCM1.2_V50_ET112/DCM1.2_V54_ET112/DCM1.2_V58_ET112/DCM1.2_V5C_ET112

13B-205V10 MR-372-J84-13B100$180.mif
13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
Tool
commandDiagnostic tool titleComments
RZ001 Fault memoryThis command is used for clearing the computer's stored
faults.
RZ002 EGR programming adaptivesUse this command when replacing the EGR valve or after it has
been cleaned.
RZ004Pressure regulation
adaptivesUse this command when replacing all four injectors at once. It
enables you to reset the injector adaptive programs.
RZ005 ProgrammingThis command enables you to reinitialise the entire computer
configuration according to the vehicle.
AC001 Preheating unitActivating this actuates the preheating unit to test the heater
plug supply. In the event of a fault, refer to the interpretation
of DF017 Preheating unit control circuit.
AC002 EGR solenoid valveThis command actuates the EGR valve. In the event of a fault,
refer to the interpretation of faults DF016 "EGR control
circuit" and DF114 "EGR solenoid valve circuit".
AC004Turbocharging solenoid
valveThis command actuates the turbocharging solenoid valve. In
the event of a fault, refer to the interpretation of faults
DF261 "Turbocharger actuator circuit" and DF427 "Turbo
actuator control".
AC005 Cylinder 1 injectorThis activation makes it possible to check injector 1 by
listening. In the event of a fault, refer to the interpretation of
fault DF026 Cylinder 1 injector control circuit.
AC006 Cylinder 2 injectorThis activation makes it possible to check injector 2 by
listening. In the event of a fault, refer to the interpretation of
fault DF027 Cylinder 2 injector control circuit.
AC007 Cylinder 3 injectorThis activation makes it possible to check injector 3 by
listening. In the event of a fault, refer to the interpretation of
fault DF028 Cylinder 3 injector control circuit.
AC008 Cylinder 4 injectorThis activation makes it possible to check injector 4 by
listening. In the event of a fault, refer to the interpretation of
fault DF029 Cylinder 4 injector control circuit.
AC010 High pressure pumpActivating this lets you listen to the operation of the high
pressure pump.
AC028 Static testThis activation allows systems to be detected and starts the
diagnostic check of the EGR and high pressure pump circuits
(Ignition switched on, engine stopped).
AC029High pressure circuit sealing
testThis activation allows the high pressure circuit sealing to be
checked after an operation has been carried out
(Engine running vehicle stopped).
DIESEL INJECTION
Fault finding – Command summary table

13B-206V10 MR-372-J84-13B100$180.mif
DIESEL INJECTION
Fault finding – Command summary table13B
DCM 1.2 Injection
Program No.: 4D
Vdiag No.: 48, 4C, 50,
54, 58, 5C
AC153* High-speed fan assemblyThis command enables the high-speed fan assembly to be
controlled. In the event of a fault, consult the interpretation of
fault DF019 High speed fan assembly control circuit.
Except Vdiag48 and 4C.
AC154* Low-speed fan assemblyThis command enables the low-speed fan assembly to be
controlled. In the event of a fault, consult the interpretation of
fault DF018 Low speed fan assembly control circuit.
Except Vdiag48 and 4C.
AC180*Air conditioning compressor
relay controlThis activation allows the air conditioning compressor clutch
relay to be controlled. In the event of a fault, refer to the
interpretation of DF489 Air conditioning compressor
control.
AC212 New pump chamber fillingActivates New pump chamber filling next time the vehicle is
started.
AC250 Heating resistor 1 relayThis activation enables the heating resistor 1 relay to be
controlled. If there is a fault, refer to the interpretation of fault
DF032 Thermoplunger 1 relay control circuit.
Only for Vdiag 50.
AC251 Heating resistor 2 relayThis activation enables the heating resistor 2 relay to be
controlled. If there is a fault, refer to the interpretation of fault
DF033 Thermoplunger 2 relay control circuit.
Only for Vdiag 50.
SC001 Write saved dataUse this command after replacing or (re)programming the
computer (if the data has been saved using command SC003).
SC002 Enter injector codesThis command enables you to manually write the calibration
code marked on the injectors. Run this command after
replacing the injectors.
SC003 Save computer dataThis command enables the computer operating data
and the engine adaptives to be recorded.
SC040 Speed limiterThis command enables the vehicle speed restriction to be
modified. Run this command after replacing or
(re)programming.
This command applies only on Kangoo 2
SC041Changing commercial
vehicle idle speedThis command enables the idle speed to be modified. Run this
command after replacing or (re)programming.
This command applies only on Kangoo 2
Tool
commandDiagnostic tool titleComments