windscreen RENAULT SCENIC 2010 J95 / 3.G Engine Compartment Connection Unit Workshop Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2010, Model line: SCENIC, Model: RENAULT SCENIC 2010 J95 / 3.GPages: 56
Page 8 of 56
87G - 8
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - System operation
87G
V6 MR-372-J84-87G000$132_eng.mif
UPC
Vdiag No.: 44
Front wipers
The UPC receives the wiping requests from the UCH via the multiplex network.
The computer then controls the following requests:
–low or high speed windscreen wiper,
–windscreen wiper park position.
Lights
The UPC receives the lighting requests from the UCH via the multiplex network.
The computer then controls the following requests:
–side lights,
–dipped beam headlights,
–main beam headlights,
–front fog light.
Detecting the oil pressure
The UPC receives the signal from the oil pressure sensor and makes it available on the multiplex network.
2. UPC LEVELS
3 UPC levels can be fitted on vehicles:
–Entry level UPC,
–Top of the range UPC N2,
–Top of the range UPC N3.
Only the top of the range N2 and N3 UPCs are available as spare parts.
The N2 and N3 versions can be distinguished in the extent to which they control the high speed blower:
–on the N2, the UPC controls an external relay,
–on N3, the relay is integrated into the UPC.
Page 18 of 56
87G - 18
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87G
V6 MR-372-J84-87G000$528_eng.mif
UPC
Vdiag No.: 44
AIR CONDITIONING: Heating
AIR CONDITIONING: Cold loop
NOTESOnly check conformity after a complete check using the diagnostic tool.
Test conditions: Engine stopped, ignition on.
Order FunctionParameter or Status
checked or Action Display and notes Fault finding
1StartingPR010:AlternatorIn %
The value must be
fixed and greater than
98%
Refer to the relevant fault
finding procedure in the
event of a fault.
AC011:Rear
windscreen
de-icingThe rear window
heating resistors and
the door mirrors (if the
vehicle is fitted with
heated door mirrors)
must be supplied with
power and heated.
Order FunctionParameter or Status
checked or Action Display and notes Fault finding
1Fan assemblyAC009:Low speed fan
unitIt must be possible to
hear the fan running at
low speed.
Refer to the relevant fault
finding procedure in the
event of a fault. AC010:High speed fan
unitIt must be possible to
hear the fan running at
high speed
This command cannot
be used on vehicles
not fitted with climate
control
2Air conditioningAC008:Compressor
commandThe compressor clutch
must be heard (the
compressor command
is not permitted when
the engine is running)
Page 19 of 56
87G - 19
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87G
V6 MR-372-J84-87G000$528_eng.mif
UPC
Vdiag No.: 44
WIPERS: Wiper power
NOTESOnly check conformity after a complete check using the diagnostic tool.
Test conditions: Engine stopped, ignition on.
Order FunctionParameter or Status
checked or Action Display and notes Fault finding
1Park positionAC012:Windscreen
wiper park
position testThe front windscreen
wiper must run for a
single sweep and
return to its initial
position.
Refer to the relevant fault
finding procedure in the
event of a fault. 2Wiper protectionET002:Front
windscreen
wiper protectionINACTIVE
3WipersAC005:Low-speed
windscreen
wiperThe windscreen wiper
must work at low
speed.
AC006:High-speed
windscreen
wiperThe windscreen wiper
must work at high
speed.
Page 23 of 56
87G - 23
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87G
V6 MR-372-J84-87G000$528_eng.mif
UPC
Vdiag No.: 44
AIR CONDITIONING: Heating
AIR CONDITIONING: Cold loop
NOTESOnly check conformity after a complete check using the diagnostic tool.
Condition for carrying out the operation: the engine must be running.
Order FunctionParameter or Status
checked or Action Display and notes Fault finding
1StartingPR010:AlternatorIn %
The value varies
according to electricity
consumption.
Refer to the relevant fault
finding method in the event
of a fault.
AC011:Rear
windscreen de-
icingThe heating resistance
for the rear window
and the door mirrors
(if the vehicle is fitted
with door mirrors) must
be supplied with power
and supply heat
Order FunctionParameter or Status
checked or Action Display and notes Fault finding
1Fan assemblyAC009:Low speed fan
unitThe fan must be heard
running at low speed
Refer to the relevant fault
finding procedure in the
event of a fault. AC010:High speed fan
unitThe fan must be heard
running at a high
speed
This command cannot
be used on vehicles
which are not fitted
with climate control
2Air conditioningAC008:Compressor
control(this command is not
permitted when the
engine is running)
Page 24 of 56
87G - 24
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87G
V6 MR-372-J84-87G000$528_eng.mif
UPC
Vdiag No.: 44
WIPERS: Wiper power
NOTESOnly check conformity after a complete check using the diagnostic tool.
Condition for carrying out this operation: the engine is running.
Order FunctionParameter or Status
checked or Action Display and notes Fault finding
1Park positionAC012:Windscreen
wiper park
position testThe windscreen wiper
must perform a single
sweep and stop at its
initial position
Refer to the relevant fault
finding procedure in the
event of a fault. Wiper protectionET002:Windscreen
wiper protectionINACTIVE
WipersAC005:Low-speed
windscreen
wiperThe windscreen wiper
must function at low
speed
AC006:Front high-
speed
windscreen
wiperThe front windscreen
wiper must function at
high speed
Page 26 of 56
87G - 26
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Status and parameter summary table87G
V6 MR-372-J84-87G000$594_eng.mif
UPC
Vdiag No.: 44ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Status and parameter summary table
Tool status Diagnostic tool title
ET001 BATTERY WARNING LIGHT
ET002 WINDSCREEN WIPER PROTECTION
ET004 REVERSE GEAR ENGAGED
ET005 MANUAL GEARBOX GEAR LEVER POSITION
ET010 START CONDITIONS SATISFIED
ET013 HIGH SPEED FAN ASSEMBLY RELAY CONTROL
ET026 + AFTER IGNITION FEED
ET027 OIL PRESSURE CONTACT
Tool parameter Diagnostic tool title
PR010 ALTERNATOR
MR-372-J84-87G000$594_eng.mif
Page 28 of 56
87G - 28
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87G
V6 MR-372-J84-87G000$660_eng.mif
UPC
Vdiag No.: 44
ET002
WINDSCREEN WIPER PROTECTION
NOTESBefore starting, check the operation of the windscreen wiper motor by running
commands AC005 Windscreen wiper at low speed and AC006 Windscreen wiper
at high speedand then check the park position using command AC012 Windscreen
wiper park position.
These statuses are listed in the order of severity or persistance of incorrect wiper
operation.
–if the status is INACTIVE, the wiper function is normal.
–If the status is LOW SPEED, the UPC has detected an abnormal wiper operation on
the higher speed setting for more than 6 seconds (the wiper has stuck or is blocked);
windscreen wiping is therefore forced to operate on the lower speed setting when
the higher speed setting is requested,
–If the status is INTERMITTENT, the wiper function is stopped for 10 seconds
following the detection and persistence of the fault (restrained or blocked),
–If the status is BLOCKED, wiping stops 30 seconds after the malfunction has lasted
for more than 2 minutes.
The status returns to INACTIVE, once the UCH requests a new wiping instruction (by
following the movement of the wiper stalk or by request from the rain sensor).
Make sure that nothing is mechanically blocking movement of the wiper blades (blades stuck, condition and
assembly of the wiper mechanism linkage and no object interfering with the motion of the device).
Check that the wiper mechanism is not seized.
Repair if necessary.
Check the status and the connection of connectors PPH2 and PEH on the UPC and of the windscreen wiper
motor.
Repair if necessary.
Page 29 of 56
87G - 29
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses
87G
V6 MR-372-J84-87G000$660_eng.mif
UPC
Vdiag No.: 44
ET002
(continued)
Check the insulation against earth and the continuity of the connections:
UPC connector PEH track 6 Track 2 of the windscreen wiper motor connector
UPC PPH2 connector track 1 Track 5 of the windscreen wiper motor connector
UPC connector PPH2 track 2 Track 4 of the windscreen wiper motor connector
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
Page 43 of 56
87G - 43
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44
AC005
LOW-SPEED WINDSCREEN WIPER
NOTESCheck:
–the condition and connection of fuse 9.
Replace it if necessary.
Check the condition and connection of connector PPH2 on the UPC.
Repair if necessary.
Check the condition and connection of the front windscreen wiper motor.
Repair if necessary.
Check for the presence of earth on track 1 of the windscreen wiper motor.
Repair if necessary.
Check for the presence of a +12 V supply on track 4 of the windscreen wiper motor while controlled by
command AC005.
If correct, replace the motor.
Check the insulation and continuity of the connection between:
UPC connector PPH2 track 2 Track 4 of the windscreen wiper motor
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.
Page 44 of 56
87G - 44
ENGINE COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of commands
87G
V6 MR-372-J84-87G000$792_eng.mif
UPC
Vdiag No.: 44
AC006
HIGH-SPEED WINDSCREEN WIPER
NOTESCheck:
–the condition and connection of fuse 9
Replace it if necessary.
Check the condition and connection of connector PPH2 on the UPC.
Repair if necessary.
Check the condition and connection of the windscreen wiper motor.
Repair if necessary.
Check for the presence of earth on track 1 of the windscreen wiper motor.
Repair if necessary.
Check for the presence of a +12 V supply on track 5 of the windscreen wiper motor while controlled by AC006.
If correct, replace the motor.
Check the insulation and continuity of the connection between:
UPC connector PPH2 track 1 Track 5 of the windscreen wiper motor
Repair if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRDeal with any other possible faults.
Switch off the ignition and carry out a road test followed by a test with the diagnostic
tool.