stop start RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 User Guide

13B-292V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
Only for Laguna II ph2 without a particle filter
ET205
ET206
ET207THERMOPLUNGER 1 RELAY CONTROLTHERMOPLUNGER 2 RELAY CONTROL
THERMOPLUNGER 3 RELAY CONTROL
STATUS
DEFINITIONACTIVE: This status indicates that the thermoplunger is supplied.
INACTIVE: This status indicates that the thermoplunger is not supplied.
NOTESNone.
"INACTIVE"Statuses ET205, ET206, ET207 are INACTIVE when the ignition is switched on
and the engine stopped, or when the engine is warm.
"ACTIVE"Statuses ET205, ET206 and ET207 are ACTIVE when the engine is started, the
engine coolant temperature is low (<15°C) and the air temperature is low (<5°).
This program allows the engine coolant to be heated to enable the passenger
compartment to be heated.
The thermoplungers also act both to load the engine to improve regeneration of
the particle filter.
To control the operation of the thermoplunger relays, run the following commands:
– AC063 Thermoplunger no.1 relay,
– AC064 Thermoplunger no. 2 relay,
– AC031 Thermoplunger no.3 relay.
In the event of a fault, refer to the interpretation of faults:
– DF034 "Thermoplunger 3 relay control circuit",
– DF033 "Heating element 2 relay control circuit",
– DF032 Thermoplunger 1 relay control circuit.
EDC16CP33_V04_ET205 / EDC16CP33_V04_ET206 / EDC16CP33_V04_ET207 / EDC16CP33_V08_ET205 / EDC16CP33_V08_ET206 /
EDC16CP33_V08_ET207 / EDC16CP33_V44_ET205 / EDC16CP33_V44_ET206 / EDC16CP33_V44_ET207 / EDC16CP33_V4C_ET205 /
EDC16CP33_V4C_ET206 / EDC16CP33_V4C_ET207 / EDC16CP33_V34_ET205 / EDC16CP33_V34_ET206 / EDC16CP33_V34_ET207 /
EDC16CP33_V38_ET205 / EDC16CP33_V38_ET206 / EDC16CP33_V38_ET207 / EDC16CP33_V74_ET205 / EDC16CP33_V74_ET206 /
EDC16CP33_V74_ET207
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 34, 38,
44, 4C, 74

13B-293V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET238SYNCHRONISATION
STATUS
DEFINITIONSynchronisation is carried out during the engine starting phase. The camshaft position
sensor and the TDC sensor are synchronised. Once this synchronisation has been
carried out, it enables the computer to identify cylinder n°1 and to ascertain the precise
position of the cylinder's top dead centre.
Synchronisation also allows the computer to determine the injection strategy.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
COMPLETEDStatus ET238 is DONE when the engine is started. The computer has identified
cylinder no. 1 and has identified the exact top dead centre position. Injection
phasing and engine management are now possible, and the engine should be
working properly.
NOT
COMPLETEDStatus ET238 is NOT COMPLETED when the engine has been stopped with the
+ after ignition feed on.
If status ET238 remains NOT COMPLETED after an attempted start, consult the
interpretation of fault DF195 Camshaft sensor/engine speed consistency.
EDC16CP33_V18_ET238 / EDC16CP33_V1C_ET238 / EDC16CP33_V54_ET238 / EDC16CP33_V20_ET238 / EDC16CP33_V58_ET238 /
EDC16CP33_V5C_ET238 / EDC16CP33_V24_ET238 / EDC16CP33_V04_ET238 / EDC16CP33_V08_ET238 / EDC16CP33_V44_ET238 /
EDC16CP33_V4C_ET238 / EDC16CP33_V34_ET238 / EDC16CP33_V38_ET238 / EDC16CP33_V74_ET238 / EDC16CP33_V28_ET238 /
EDC16CP33_V62_ET238 / EDC16CP33_V26_ET238 / EDC16CP33_V60_ET238
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-295V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET341IMMOBILISER CODE PROGRAMMED
STATUS
DEFINITIONYES: This status indicates that the immobiliser code has been programmed.
NO: This status indicates that the immobiliser code has not been programmed.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
"YES"Status ET341 is YES if dialogue is possible between the UCH computer and the
injection computer and the key code is recognised
.
The engine is only authorised to start if the code is correctly recognised by the UCH
computer and statusET003 Engine immobiliser is INACTIVE.
In the event of a fault, (see 87B, Passenger compartment connection unit,
Conformity check).
"NO"Status ET341 is NO if dialogue is not possible between the UCH computer and the
injection computer (status ET003 remains ACTIVE).
This fault may be caused by incorrect key programming or a lack of key programming.
In this case, refer to the UCH fault-finding note (see 87B, Passenger compartment
connection unit) and follow the key programming procedure.
If the key programming is not the cause, run a multiplex network test (see 88B,
Multiplexing) and check that dialogue between the UCH and the injection
computer is possible.
If dialogue is not established, contact Techline.
EDC16CP33_V18_ET341 / EDC16CP33_V1C_ET341 / EDC16CP33_V54_ET341 / EDC16CP33_V20_ET341 / EDC16CP33_V58_ET341 /
EDC16CP33_V5C_ET341 / EDC16CP33_V24_ET341 / EDC16CP33_V04_ET341 / EDC16CP33_V08_ET341 / EDC16CP33_V44_ET341 /
EDC16CP33_V4C_ET341 / EDC16CP33_V34_ET341 / EDC16CP33_V38_ET341 / EDC16CP33_V74_ET341 / EDC16CP33_V28_ET341 /
EDC16CP33_V62_ET341 / EDC16CP33_V26_ET341 / EDC16CP33_V60_ET341
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-308V12 MR-372-J84-13B300$101.mif
DIESEL INJECTION
Fault finding – Interpretation of statuses13B
ET651EGR PROGRAMMING CUT-OFF
STATUS
DEFINITIONThis status indicates the operating mode of the EGR valve and has 25 different
definitions: STATUS 1 to 24 or NONE.
NOTESNone.
NONENo EGR cut-off, the EGR valve is operating correctly in accordance with
the computer programs.
STATUSES
1, 5, 6, 7, 9, 10, 12,
13, 15, 19, 23, 24Switch off the engine and wait for the diagnostic tool message (maximum time
8 minutes) Communication lost with the computer: EDC16CP33, check the
tool connection and computer supply.
Switch the ignition on and check for faults.
Check the battery voltage with the engine switched off and the engine running.
If no faults are present or stored, restart the vehicle and test at idle speed.
Do not accelerate too much or attain an engine speed that is too high.
STATUSES
3, 14, 16Accelerate above idle speed for a few seconds.
STATUS 2Check that the clutch pedal status (ET405 Clutch pedal switch) is not ACTIVE,
and that the vehicle has stopped completely.
EDC16CP33_V18_ET651 / EDC16CP33_V1C_ET651 / EDC16CP33_V54_ET651 / EDC16CP33_V20_ET651 / EDC16CP33_V58_ET651 /
EDC16CP33_V5C_ET651 / EDC16CP33_V24_ET651 / EDC16CP33_V04_ET651 / EDC16CP33_V08_ET651 / EDC16CP33_V44_ET651 /
EDC16CP33_V4C_ET651 / EDC16CP33_V34_ET651 / EDC16CP33_V38_ET651 / EDC16CP33_V74_ET651 / EDC16CP33_V28_ET651 /
EDC16CP33_V62_ET651 / EDC16CP33_V26_ET651 / EDC16CP33_V60_ET651
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-344
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR038RAIL PRESSURE
PARAMETER
DEFINITIONThis parameter indicates the rail pressure in bar.
NOTESThere must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (starting faults, poor performance, stalling etc.),
– after interpretation of command AC225 Rail pressure regulator.
Special notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
Conformity check: Engine stopped and ignition on
The rail pressure value is between:
0 bar < PR038 < 90 bar if the coolant temperature < 30°C.
In the event of a fault, consult the interpretation of fault DF007 Rail pressure sensor circuit.
Conformity check with the engine running and engine coolant temperature > 80°C
The rail pressure value must be between:
250 bar < PR038 < 290 bar (at idle speed),
1680 bar < PR038 < 1720 bar (full load).
In the event of a fault, refer to the interpretation of fault DF007.
EDC16CP33_V18_PR038 / EDC16CP33_V1C_PR038 / EDC16CP33_V54_PR038 / EDC16CP33_V20_PR038 / EDC16CP33_V58_PR038 /
EDC16CP33_V5C_PR038 / EDC16CP33_V24_PR038 / EDC16CP33_V04_PR038 / EDC16CP33_V08_PR038 / EDC16CP33_V44_PR038 /
EDC16CP33_V4C_PR038 / EDC16CP33_V34_PR038 / EDC16CP33_V38_PR038 / EDC16CP33_V74_PR038 / EDC16CP33_V38_PR028 /
EDC16CP33_V62_PR038 / EDC16CP33_V26_PR038 / EDC16CP33_V60_PR038
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-347
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR041
CONTINUED
Sensor electrical conformity
Check the continuity and absence of interference resistance of the following connections:
•3LQ between components 120 and 1071,
•3LP between components 120 and 1071,
•3LN between components 120 and 1071.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Vehicle with the ignition on, and the engine stopped for at least 1 minute:
Compare the values of PR041 Turbocharging pressure and PR035 Atmospheric pressure.
If the difference between PR041 and PR035 is greater than 0.1 bar,
check the value of PR035 by comparing it with the reading on a vehicle in the workshop which is correct.
If the value of PR035 is not correct (difference greater than 0.1 bar between the 2 vehicles), contact the Techline.
Otherwise (when the value of PR035 is correct), replace the turbocharger pressure sensor.
If the difference between PR041 and PR035 is less than 0.1 bar.
Start the engine, with the engine idling:
Compare the values of PR041 and PR035.
If the difference between PR041 and PR035 is greater than 0.2 bar.
Check the air inlet circuit:
Apply Test 4 Turbocharged air inlet circuit check.
Low and high pressure air circuit sealed and not obstructed: ducts, mounting clamps present and tightened,
turbocharging pressure sensor fitted, exchanger, etc.
Check that the damper valve is not jammed closed.
Repair if necessary.
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-375V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR132
CONTINUED
Sensor electrical conformity
Check the air inlet circuit (from the air filter inlet to the inlet manifold,
apply Test 4 Turbocharged air inlet circuit check):
– air filter unit inlet not blocked and filter not clogged,
–visual inspection only, apply Test 4 of ALP 2 Starting fault or starting impossible,
– oil vapour recirculation circuit connection conformity.
–absence of leaks or blockages in the low and high pressure air circuits: pipes, presence and tightness of the
mounting clips, mounting of the turbocharger pressure sensor, intercooler, etc.
– check that the damper valve is not jammed closed.
Carry out the necessary repairs.
Check the electrical conformity of the air flowmeter:
Check the + 5 V supply of the air flowmeter on the following connection:
•3KJ of component 799.
Check the + 12 V after relay supply of the air flowmeter on the following connection:
•3FB of component 799.
Check the continuity and absence of interference resistance of the following connections:
•3DV between components 120 and 799,
•3DW between components120 and 799.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the flowmeter connected, the vehicle ignition on, and the engine stopped:
Check the voltage between connections 3DW and 3DV of component 799.
If the air flow sensor voltage is not between 0.3 V < X < 0.7 V, replace the sensor.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-408V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR816
PR817
PR818
PR819
PR820
PR821
PR822
PR823
PR824
PR825STORED REGENERATION START NO. 1
STORED REGENERATION START NO. 2
STORED REGENERATION START NO. 3
STORED REGENERATION START NO. 4
STORED REGENERATION START NO. 5
STORED REGENERATION START NO. 6
STORED REGENERATION START NO. 7
STORED REGENERATION START NO. 8
STORED REGENERATION START NO. 9
STORED REGENERATION START NO. 10
PARAMETER
DEFINITIONThese parameters are shown in miles (km).
NOTESSpecial notes:
These parameters should only be interpreted for ALP 9 Particle filter warning light
comes on too frequently.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
These parameters are used so that the history of the last ten illuminations of the particle filter warning light are
known.
EDC16CP33_V18_PR816 / EDC16CP33_V18_PR817 / EDC16CP33_V18_PR818 / EDC16CP33_V18_PR819 / EDC16CP33_V18_PR820 /
EDC16CP33_V18_PR821 / EDC16CP33_V18_PR822 / EDC16CP33_V18_PR823 / EDC16CP33_V18_PR824 / EDC16CP33_V18_PR825 /
EDC16CP33_V1C_PR816 / EDC16CP33_V1C_PR817 / EDC16CP33_V1C_PR818 / EDC16CP33_V1C_PR819 / EDC16CP33_V1C_PR820 /
EDC16CP33_V1C_PR821 / EDC16CP33_V1C_PR822 / EDC16CP33_V1C_PR823 / EDC16CP33_V1C_PR824 / EDC16CP33_V1C_PR825 /
EDC16CP33_V54_PR816 / EDC16CP33_V54_PR817 / EDC16CP33_V54_PR818 / EDC16CP33_V54_PR819 / EDC16CP33_V54_PR820 /
EDC16CP33_V54_PR821 / EDC16CP33_V54_PR822 / EDC16CP33_V54_PR823 / EDC16CP33_V54_PR824 / EDC16CP33_V54_PR825 /
EDC16CP33_V20_PR816 / EDC16CP33_V20_PR817 / EDC16CP33_V20_PR818 / EDC16CP33_V20_PR819 / EDC16CP33_V20_PR820 /
EDC16CP33_V20_PR821 / EDC16CP33_V20_PR822 / EDC16CP33_V20_PR823 / EDC16CP33_V20_PR824 / EDC16CP33_V20_PR825 /
EDC16CP33_V58_PR816 / EDC16CP33_V58_PR817 / EDC16CP33_V58_PR818 / EDC16CP33_V58_PR819 / EDC16CP33_V58_PR820 /
EDC16CP33_V58_PR821 / EDC16CP33_V58_PR822 / EDC16CP33_V58_PR823 / EDC16CP33_V58_PR824 / EDC16CP33_V58_PR825 /
EDC16CP33_V5C_PR816 / EDC16CP33_V5C_PR817 / EDC16CP33_V5C_PR818 / EDC16CP33_V5C_PR819 / EDC16CP33_V5C_PR820 /
EDC16CP33_V5C_PR821 / EDC16CP33_V5C_PR822 / EDC16CP33_V5C_PR823 / EDC16CP33_V5C_PR824 / EDC16CP33_V5C_PR825 /
EDC16CP33_V24_PR816 / EDC16CP33_V24_PR817 / EDC16CP33_V24_PR818 / EDC16CP33_V24_PR819 / EDC16CP33_V24_PR820 /
EDC16CP33_V24_PR821 / EDC16CP33_V24_PR822 / EDC16CP33_V24_PR823 / EDC16CP33_V24_PR824 / EDC16CP33_V24_PR825 /
EDC16CP33_V26_PR816 / EDC16CP33_V26_PR817 / EDC16CP33_V26_PR818 / EDC16CP33_V26_PR819 / EDC16CP33_V26_PR820 /
EDC16CP33_V26_PR821 / EDC16CP33_V26_PR822 / EDC16CP33_V26_PR823 / EDC16CP33_V26_PR824 / EDC16CP33_V26_PR825 /
EDC16CP33_V60_PR816 / EDC16CP33_V60_PR817 / EDC16CP33_V60_PR818 / EDC16CP33_V60_PR819 / EDC16CP33_V60_PR820 /
EDC16CP33_V60_PR821 / EDC16CP33_V60_PR822 / EDC16CP33_V60_PR823 / EDC16CP33_V60_PR824 / EDC16CP33_V60_PR825
EDC16CP33
Program No.: C4
Vdiag No.: 18, 1C, 20, 24,
26, 54, 58, 5C, 60
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-427V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
SC017PARTICLE FILTER REGENERATION
NOTESOnly run this command after interpretation of the following faults:
– DF308 Clogged particle filter,
– DF311 Failed regenerations limit exceeded,
– df312: speed request.
WARNING:
– It is essential to observe the health and safety guidelines (see MR364 (Mégane II ph2), MR370 (Scénic II ph2),
MR 395 (Laguna II ph2), 402 (Vel Satis ph2), 405 (Espace IV ph2) Mechanical, 19B, Exhaust, Particle
filter: Cleaning) and follow the procedure below.
SAFETY INSTRUCTIONS TO BE FOLLOWED:
The regeneration causes exhaust fumes and high temperatures.
It is strongly recommended that you put the vehicle outside during regeneration.
If it is not possible to carry out regeneration outside, use an extractor fan that can withstand the very high
regeneration temperatures (400°C at the exhaust outlet).
Perform regeneration on a surface free from fire risks (oil, dry leaves, etc.).
Nothing should be left in the vicinity of the exhaust pipe.
Check that there are no leaks or blockages in the exhaust pipe,
Repair if necessary.
WARNING:
Check the engine oil level before running the command to avoid any engine racing. The oil level must be
between the minimum level and the middle level on the oil dipstick.
Before performing a particle filter regeneration, it is essential to deactivate the air conditioning
compressor (risk of engine damage) and all the electrical consumers.
IF NECESSARY:
Regeneration can be stopped by pressing the engine start button twice briefly (less than 3 seconds).
Switch off the ignition and wait for the diagnostic tool message (maximum time 8 minutes) Communication
lost with computer: EDC16 C33, check the tool connection and the computer power supply before
switching the ignition back on.
EDC16CP33_V1C_SC017 / EDC16CP33_V54_SC017 / EDC16CP33_V20_SC017 / EDC16CP33_V58_SC017 / EDC16CP33_V5C_SC017 /
EDC16CP33_V24_SC017 / EDC16CP33_V28_SC017 / EDC16CP33_V62_SC017/ EDC16CP33_V26_SC017 / EDC16CP33_V60_SC017
EDC16CP33
Program No.: C4
Vdiag No.: 1C, 20, 24, 26,
28, 54, 58, 5C, 60, 62
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-440V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC004
CONTINUED
Run command AC004; if a faint whistling noise is heard along with a clicking from the solenoid valve, go to STEP
2, otherwise check the operation of the computer output stage:
Vehicle under + after ignition feed, clear the faults displayed by the diagnostic tool.
With the voltmeter in the direct current position:
With the turbocharging solenoid valve connected, connect the voltmeter earth lead to connection 3MG of
component 1475 and the positive lead to connection 3FB of component 1475. Run command AC004; the
voltmeter must display four successive voltages between 2.2 V and 2.6 V.
If the measurement is not correct, contact the Techline.
2. turbocharger control circuit check
–Apply Test 7 Variable geometry turbocharger control.
– With the engine stopped, make sure that the control rod is in the resting position.
– Start the engine and make sure that the control rod actuates to the upper stop.
(when the engine stops, the control rod should return to the rest position).
If the control rod does not move correctly, carry out the following checks:
1. Check the control vacuum:
– Disconnect the solenoid valve inlet hose and connect it to a pressure gauge.
– Start the engine and run it at a stable idle speed.
If the vacuum does not reach a value between 0.250 bar and 0.550 bar, check the vacuum circuit from the
vacuum pump.
– Stop the engine, reconnect the inlet hose and move onto step no. 2.
2. Check the solenoid valve actuation:
– Disconnect the solenoid valve outlet hose.
– Start the engine and run it at a stable idle speed.
– Place your hand on the solenoid valve and block the outlet union with your thumb.
– If there is no perceptible vibration of the solenoid valve, contact the Techline.
3. Check the solenoid valve actuation:
– Connect the pressure gauge to the solenoid valve outlet union.
– Start the engine and run it at a stable idle speed.
If the vacuum does not reach a value between 0.250 bar and 0.550 bar, replace the solenoid valve.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.