ABS RENAULT SCENIC 2012 J95 / 3.G Engine And Peripherals EDC16CP33 Manual Online

13B-350
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR051EGR VALVE POSITION FEEDBACK
PARAMETER
DEFINITIONThis parameter indicates the opening ratio of the EGR valve in %.
NOTESThere must be no present or stored faults.
Perform this fault finding procedure:
– after finding an inconsistency in the parameter,
– after a customer complaint (loss of power, smoke etc.).
– after interpretation of command AC103 EGR by-pass.
Use the Technical Note Wiring Diagram, Laguna II ph2, Vel Satis ph2, Mégane ll
ph2, Scénic ll ph2, Espace IV ph2.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
In the event of a fault, see the interpretation of faults DF209 EGR valve position sensor circuit and DF647 EGR
valve position regulation.
Sensor electrical conformity
Check the continuity and absence of interference resistance of the following connections:
•3JM between components 120 and 1460 or 169,
•3EL between components 120 and 1460 or 169,
•3GC between components 120 and 1460 or 169.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
EDC16CP33_V18_PR051 / EDC16CP33_V1C_PR051 / EDC16CP33_V54_PR051 / EDC16CP33_V20_PR051 / EDC16CP33_V58_PR051 /
EDC16CP33_V5C_PR051 / EDC16CP33_V24_PR051 / EDC16CP33_V04_PR051 / EDC16CP33_V08_PR051 / EDC16CP33_V44_PR051 /
EDC16CP33_V4C_PR051 / EDC16CP33_V34_PR051 / EDC16CP33_V38_PR051 / EDC16CP33_V74_PR051 / EDC16CP33_V28_PR051 /
EDC16CP33_V62_PR051 / EDC16CP33_V26_PR051 / EDC16CP33_V60_PR051
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-357
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR063
CONTINUED
Sensor electrical conformity
Check the continuity and absence of interference resistance of the following connections:
•3FAB between components 120 and 1066,
•3LD between components 120 and 1066.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance between the following connections:
•3FAB and 3LD of component 1066.
If the fuel temperature sensor resistances are not between:
3538 Ω < X < 4502 Ω (at + 10°C),
1950 Ω < X < 2150 Ω (at + 25°C),
763 Ω < X < 857 Ω (at +50°C),
replace the sensor.
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-359
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR064
CONTINUED
Sensor electrical conformity
Check the continuity and absence of interference resistance of the following connections:
•3C between components 120 and 244,
•3JK between components 120 and 244,
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Measure the resistance between the following connections:
•3C and 3JK of component 244.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the temperature sensor resistances are not between:
11332 Ω < X < 13588 Ω (at - 10°C),
2140 Ω < X < 2364 Ω (at + 25°C),
772 Ω < X < 850 Ω (at + 50°C),
275 Ω < X < 291 Ω (at + 80°C),
112 Ω < X < 118 Ω (at + 110°C),
replace the sensor.
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-369
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.
V12 MR-372-J84-13B300$121.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR089VEHICLE SPEED
PARAMETER
DEFINITIONGives the vehicle speed in km/h.
NOTESSpecial notes:
Only perform these tests if the parameters do not correspond with the system
operation programming.
This parameter is transmitted by the ABS computer. This signal is transmitted to the
injection on the multiplex network.
Conformity check: Engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
In the event of a fault, test the multiplex network (see 88B, Multiplex).
And then complete fault finding on the ABS computer (see 38C, Anti-lock braking system).
EDC16CP33_V18_PR089 / EDC16CP33_V1C_PR089 / EDC16CP33_V54_PR089 / EDC16CP33_V20_PR089 / EDC16CP33_V58_PR089 /
EDC16CP33_V5C_PR089 / EDC16CP33_V24_PR089 / EDC16CP33_V04_PR089 / EDC16CP33_V08_PR089 / EDC16CP33_V44_PR089 /
EDC16CP33_V4C_PR089 / EDC16CP33_V34_PR089 / EDC16CP33_V38_PR089 / EDC16CP33_V74_PR089 / EDC16CP33_V28_PR089 /
EDC16CP33_V62_PR089 / EDC16CP33_V26_PR089 / EDC16CP33_V60_PR089
EDC16CP33
Program No.: C4
VDiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74

13B-375V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR132
CONTINUED
Sensor electrical conformity
Check the air inlet circuit (from the air filter inlet to the inlet manifold,
apply Test 4 Turbocharged air inlet circuit check):
– air filter unit inlet not blocked and filter not clogged,
–visual inspection only, apply Test 4 of ALP 2 Starting fault or starting impossible,
– oil vapour recirculation circuit connection conformity.
–absence of leaks or blockages in the low and high pressure air circuits: pipes, presence and tightness of the
mounting clips, mounting of the turbocharger pressure sensor, intercooler, etc.
– check that the damper valve is not jammed closed.
Carry out the necessary repairs.
Check the electrical conformity of the air flowmeter:
Check the + 5 V supply of the air flowmeter on the following connection:
•3KJ of component 799.
Check the + 12 V after relay supply of the air flowmeter on the following connection:
•3FB of component 799.
Check the continuity and absence of interference resistance of the following connections:
•3DV between components 120 and 799,
•3DW between components120 and 799.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the flowmeter connected, the vehicle ignition on, and the engine stopped:
Check the voltage between connections 3DW and 3DV of component 799.
If the air flow sensor voltage is not between 0.3 V < X < 0.7 V, replace the sensor.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-401V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
PR739FUEL FLOW SOLENOID VALVE CURRENT
PARAMETER
DEFINITIONThis parameter indicates the current absorbed by the fuel flow solenoid valve inmA.
Conformity check with engine stopped and ignition on.
The value of the current absorbed by the fuel flow solenoid valve must be:
PR739 ≈ 200 mA.
In the event of a fault, consult the interpretation of DF897 Pump pressure regulator circuit.
Conformity check with the engine running and engine coolant temperature > 80°C
The value of the current absorbed by the fuel flow solenoid valve must be:
PR739 ≈ 300 mA.
In the event of a fault, refer to the interpretation of fault DF897.
EDC16CP33_V18_PR739 / EDC16CP33_V1C_PR739 / EDC16CP33_V54_PR739 / EDC16CP33_V20_PR739 / EDC16CP33_V58_PR739 /
EDC16CP33_V5C_PR739 / EDC16CP33_V24_PR739 / EDC16CP33_V04_PR739 / EDC16CP33_V08_PR739 / EDC16CP33_V44_PR739 /
EDC16CP33_V4C_PR739 / EDC16CP33_V34_PR739 / EDC16CP33_V38_PR739 / EDC16CP33_V74_PR739 / EDC16CP33_V28_PR739 /
EDC16CP33_V62_PR739 / EDC16CP33_V26_PR739 / EDC16CP33_V60_PR739
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-412V12 MR-372-J84-13B300$122.mif
DIESEL INJECTION
Fault finding – Interpretation of parameters13B
SOLEN.*: Solenoid valve
PR850FUEL FLOW SOLEN.* CURRENT SETPOINT
PARAMETER
DEFINITIONThis parameter indicates the setpoint for the current absorbed by the fuel flow solenoid
valve in mA.
NOTESNone.
Conformity check with engine stopped and ignition on, or engine running, and engine coolant
temperature > 80°C
This parameter indicates the setpoint for the current absorbed by the fuel flow solenoid valve.
EDC16CP33_V18_PR850 / EDC16CP33_V1C_PR850 / EDC16CP33_V54_PR850 / EDC16CP33_V20_PR850 / EDC16CP33_V58_PR850 /
EDC16CP33_V5C_PR850 / EDC16CP33_V24_PR850 / EDC16CP33_V04_PR850 / EDC16CP33_V08_PR850 / EDC16CP33_V44_PR850 /
EDC16CP33_V4C_PR850 / EDC16CP33_V34_PR850 / EDC16CP33_V38_PR850 / EDC16CP33_V74_PR850 / EDC16CP33_V28_PR850 /
EDC16CP33_V62_PR850 / EDC16CP33_V26_PR850 / EDC16CP33_V60_PR850
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-441V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC012DAMPER VALVE
NOTESCarry out this interpretation:
– after DF645 Damper valve position regulation, DF646 Damper valve position
sensor,
– or after a customer complaint (starting faults, poor performance).
Use the Wiring Diagram Technical Note, Laguna II ph2, Mégane ll, Scénic ll,
Espace IV ph2, Vel Satis ph2.
Measure the resistance between connections 38KQ and 38KP of component 1461.
If the resistance is not between 875 Ω and 1625 Ω replace the damper valve.
Check the continuity and absence of interference resistance of the following connections:
•38KQ between components 120 and 1461,
•38KP between components 120 and 1461.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
With the vehicle ignition on, and the engine stopped:
Make sure the damper flap is open,
If not, clean or replace the damper valve.
Actuate the valve using command AC012 and check the damper valve travel and rest position of the valve.
Check the operation of the computer output stage with a voltmeter in the alternating current position:
Actuate the valve with command AC012.
Connect the voltmeter earth lead to connection 38KS of component 1461 and the positive lead to connection
38KQ of component 1461.
The voltmeter should display three cycles of ON-OFF (12.5 V then return to 0V).
If the measurement is correct, replace the damper valve
If the measurement does not show any operation, contact the Techline.
EDC16CP33_V18_AC012 / EDC16CP33_V1C_AC012 / EDC16CP33_V54_AC012 / EDC16CP33_V20_AC012 / EDC16CP33_V58_AC012 /
EDC16CP33_V5C_AC012 / EDC16CP33_V24_AC012 / EDC16CP33_V04_AC012 / EDC16CP33_V08_AC012 / EDC16CP33_V44_AC012 /
EDC16CP33_V4C_AC012 / EDC16CP33_V34_AC012 / EDC16CP33_V38_AC012 / EDC16CP33_V74_AC012 / EDC16CP33_V28_AC012 /
EDC16CP33_V62_AC012 / EDC16CP33_V26_AC012 / EDC16CP33_V60_AC012
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-445V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC037
CONTINUED
STEP 2:
Check the connections of the preheating unit, component code 257, the heater plugs, component codes 680, 681,
682 and 683 and the injection computer, component code 120.
Measure the resistance of the heater plugs. If the resistance value is > 2 Ω, replace the faulty plug or plugs,
making sure that the correct plug type, slow or fast, is fitted on the vehicle.
Check the continuity and absence of interference resistance of the following connections:
•37AB between components 257 and 683,
•37AA between components 257 and 680,
•37Z between components 257 and 681,
•37AC between components 257 and 682.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the condition of the preheating unit supply fuse (70 A) (see MR 364 (Mégane II ph2), MR 370 (Scénic II
ph2), MR 395 (Laguna II ph2), 402 (Vel Satis ph2), 405 (Espace IV ph2) Mechanical, 81C, Fuses, Fuses: List
and location of components).
Check the + 12 V battery supply to the preheating unit on the following connection:
•BP35 of component 257.
Check the continuity and absence of interference resistance of the following connections:
•3FY between components120 and 257,
•3FF between components120 and 257.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, replace the preheating unit.
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.

13B-450V12 MR-372-J84-13B300$150.mif
DIESEL INJECTION
Fault finding – Interpretation of commands13B
AC103EGR BY-PASS
NOTESCarry out this fault finding procedure when the interpretation of fault DF304 EGR
bypass circuit has not been resolved.
Use the Wiring Diagram Technical Note, Laguna II ph2, Vel Satis ph2, Espace IV
ph2, Mégane II ph2, Scénic II ph2.
Measure the resistance between connections 3FB and 3TP of component 1301.
If the resistance of the solenoid valve is not between:
•43 Ω and 49 Ω at + 25 °C,
•32 Ω and 37 Ω at - 40 °C, replace the EGR bypass solenoid valve.
Check the continuity and the absence of interference resistance on the following connection:
•3TP between components 120 and 1301.
Check the + 12 V after relay supply to the EGR bypass solenoid valve of the following connection:
•3FB of component 1301.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If you notice no valve movement when running command AC103, ensure that the computer output stage is
functioning:
Vehicle under + after ignition feed, clear the faults displayed by the diagnostic tool.
EDC16CP33_V18_AC103 / EDC16CP33_V1C_AC103 / EDC16CP33_V54_AC103 / EDC16CP33_V20_AC103 / EDC16CP33_V58_AC103 /
EDC16CP33_V5C_AC103 / EDC16CP33_V24_AC103 / EDC16CP33_V04_AC103 / EDC16CP33_V08_AC103 / EDC16CP33_V44_AC103 /
EDC16CP33_V4C_AC103 / EDC16CP33_V34_AC103 / EDC16CP33_V38_AC103 / EDC16CP33_V74_AC103 / EDC16CP33_V28_AC103 /
EDC16CP33_V62_AC103 / EDC16CP33_V26_AC103 / EDC16CP33_V60_AC103
EDC16CP33
Program No.: C4
Vdiag No.: 04, 08, 18, 1C,
20, 24, 26, 28, 34, 38, 44,
4C, 54, 58, 5C, 60, 62, 74
AFTER REPAIRCarry out a road test, then check with the diagnostic tool.